Toyota Camry (2020 year). Manual in english — part 8
456
6-3. Do-it-yourself maintenance
CAMRY_U
■
When registering ID codes (vehicles with a tire inflation pressure dis-
play function)
●
Before performing ID code registration, make sure that no wheels with
tire pressure warning valve and transmitters installed are near the vehi-
cle.
●
Make sure to initialize the tire pressure warning system after registering
the ID codes. If the system is initialized before registering the ID codes,
the initialized values will be invalid.
●
As the tires will be warm when registration is completed, make sure to
allow the tires to cool before performing initialization.
■
Canceling ID code registration (vehicles with a tire inflation pressure
display function)
●
To cancel ID code registration after it has been started, turn the engine
switch off before driving the vehicle.
If the vehicle is driven after ID code registration is started, to cancel reg-
istration, perform the ID code registration start procedure again and turn
the engine switch off before driving.
●
If ID code registration has been canceled, the tire pressure warning light
will blink for approximately 1 minute when the engine switch is turned to
the “ON” position (vehicles without a smart key system) or IGNITION
ON mode (vehicles with a smart key system) and then illuminate. The
tire pressure warning system will be operational when the tire pressure
warning light turns off.
●
If the warning light does not turn off even after several minutes have
elapsed, ID code registration may not have been cancelled correctly. To
cancel registration, perform the ID code registration start procedure
again and then turn the engine switch off before driving.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
457
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
■
If ID codes are not registered properly (vehicles with a tire inflation
pressure display function)
●
In the following situations, ID code registration may take longer than
usual to be completed or may not be possible. (Usually, the vehicle will
need to be driven for approximately 10 to 30 minutes to complete ID
code registration.)
If ID code registration is not complete after driving for approximately 30
minutes, continue driving for a while.
• If the vehicle is driven on an unpaved road, it may take longer than
normal to complete registration.
• If the vehicle is backed up while performing registration, data col-
lected during registration will be cleared, and it will take longer than
normal to complete.
• If the vehicle is driven in heavy traffic or another situation where other
vehicles are driven close by, it may take time for the system to recog-
nize the tire pressure warning valve and transmitters of your vehicle
over those of other vehicles.
• If a wheel with a tire pressure warning valve and transmitter installed
is inside or near the vehicle, registration of the ID codes for the
installed wheels may not be possible.
If ID registration is not complete after driving for approximately 1 hour,
park the vehicle in a safe place for approximately 20 minutes and then
perform the ID code registration procedure again.
●
In the following situations, ID code registration will not be started or was
not completed properly and the system will not operate properly. Per-
form the ID code registration procedure again.
• If, when attempting to start ID code registration, the tire pressure
warning light does not blink slowly 3 times.
• If, when the vehicle has been driven for about 20 minutes after per-
forming ID code registration, the tire pressure warning light blinks for
approximately 1 minute and then illuminates.
●
If ID code registration cannot be completed after performing the above
procedure, contact your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
458
6-3. Do-it-yourself maintenance
CAMRY_U
■
Tire pressure warning system certification
For vehicles sold in the U.S.A.
For vehicles sold in Canada
Model: PMV-E000
-------------------------------------------------------------------------------------------------------------------------------------------------------------
459
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
WARNING
■
When inspecting or replacing tires
Observe the following precautions to prevent accidents.
Failure to do so may cause damage to parts of the drive train as well as
dangerous handling characteristics, which may lead to an accident
resulting in death or serious injury.
●
Do not mix tires of different makes, models or tread patterns.
Also, do not mix tires of remarkably different treadwear.
●
Do not use tire sizes other than those recommended by Toyota.
●
Do not mix differently constructed tires (radial, bias-belted or bias-ply
tires).
●
Do not mix summer, all season and snow tires.
●
Do not use tires that have been used on another vehicle.
Do not use tires if you do not know how they were used previously.
■
When initializing the tire pressure warning system
Do not initialize the tire pressure warning system without first adjusting
the tire inflation pressure to the specified level. Otherwise, the tire pres-
sure warning light may not come on even if the tire inflation pressure is
low, or it may come on when the tire inflation pressure is actually nor-
mal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
460
6-3. Do-it-yourself maintenance
CAMRY_U
NOTICE
■
Repairing or replacing tires, wheels, tire pressure warning valve
and transmitters and tire valve caps
●
When removing or fitting the wheels, tires or the tire pressure warning
valve and transmitters, contact your Toyota dealer as the tire pressure
warning valve and transmitters may be damaged if not handled cor-
rectly.
●
Make sure to install the tire valve caps. If the tire valve caps are not
installed, water may enter the valves of the tire pressure warning valve
and transmitters and the valves may become stuck.
●
When replacing tire valve caps, do not replace them with metal caps or
any tire valve caps other than specified, as they may become stuck.
■
To avoid damage to the tire pressure warning valve and transmit-
ters
When a tire is repaired with liquid sealants, the tire pressure warning
valve and transmitter may not operate properly. If a liquid sealant is
used, contact your Toyota dealer or other qualified service shop as soon
as possible. Make sure to replace the tire pressure warning valve and
transmitter when replacing the tire. (
■
Driving on rough roads
Take particular care when driving on roads with loose surfaces or pot-
holes.
These conditions may cause losses in tire inflation pressure, reducing
the cushioning ability of the tires. In addition, driving on rough roads
may cause damage to the tires themselves, as well as the vehicle’s
wheels and body.
■
Low profile tires (vehicles with 18 or 19-inch wheels)
Low profile tires may cause greater damage than usual to the tire wheel
when sustaining impact from the road surface. Therefore, pay attention
to the following:
●
Be sure to use proper tire inflation pressure. If tires are under-inflated,
they may be damaged more severely.
●
Avoid potholes, uneven pavement, curbs and other road hazards. Fail-
ure to do so may lead to severe tire and wheel damage.
■
If tire inflation pressure of each tire becomes low while driving
Do not continue driving, or your tires and/or wheels may be ruined.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
461
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
The recommended cold tire inflation pressure and tire size are dis-
played on the tire and loading information label. (
Tire inflation pressure
Tire inflation pressure
Type A
Type B
-------------------------------------------------------------------------------------------------------------------------------------------------------------
462
6-3. Do-it-yourself maintenance
CAMRY_U
Tire valve
Tire pressure gauge
Remove the tire valve cap.
Press the tip of the tire pressure gauge onto the tire valve.
Read the pressure using the gauge gradations.
If the tire inflation pressure is not at the recommended level, adjust
the pressure.
If you add too much air, press the center of the valve to deflate.
After completing the tire inflation pressure measurement and
adjustment, apply soapy water to the valve and check for leakage.
Put the tire valve cap back on.
■
Tire inflation pressure check interval
You should check tire inflation pressure every two weeks, or at least once
a month.
Do not forget to check the spare.
■
Effects of incorrect tire inflation pressure
Driving with incorrect tire inflation pressure may result in the following:
●
Reduced fuel economy
●
Reduced driving comfort and poor handling
●
Reduced tire life due to wear
●
Reduced safety
●
Damage to the drivetrain
If a tire needs frequent inflating, have it checked by your Toyota dealer.
Inspection and adjustment procedure
1
2
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
463
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
■
Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following:
●
Check only when the tires are cold.
If your vehicle has been parked for at least 3 hours or has not been
driven for more than 1 mile or 1.5 km, you will get an accurate cold tire
inflation pressure reading.
●
Always use a tire pressure gauge.
It is difficult to judge if a tire is properly inflated based only on its appear-
ance.
●
It is normal for the tire inflation pressure to be higher after driving as
heat is generated in the tire. Do not reduce tire inflation pressure after
driving.
●
Never exceed the vehicle capacity weight.
Passengers and luggage weight should be placed so that the vehicle is
balanced.
WARNING
■
Proper inflation is critical to save tire performance
Keep your tires properly inflated.
If the tires are not properly inflated, the following conditions may occur
which could lead to an accident resulting in death or serious injury:
●
Excessive wear
●
Uneven wear
●
Poor handling
●
Possibility of blowouts resulting from overheated tires
●
Air leaking from between tire and wheel
●
Wheel deformation and/or tire damage
●
Greater possibility of tire damage while driving (due to road hazards,
expansion joints, sharp edges on the road, etc.)
NOTICE
■
When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on.
If a valve cap is not installed, dirt or moisture may get into the valve and
cause an air leak, resulting in decreased tire inflation pressure.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
464
6-3. Do-it-yourself maintenance
CAMRY_U
When replacing wheels, care should be taken to ensure that they are
equivalent to those removed in load capacity, diameter, rim width and
inset
*
.
Replacement wheels are available at your Toyota dealer.
*
: Conventionally referred to as “offset”.
Toyota does not recommend using the following:
●
Wheels of different sizes or types
●
Used wheels
●
Bent wheels that have been straightened
●
Use only Toyota wheel nuts and wrenches designed for use with
your aluminum wheels.
●
When rotating, repairing or changing your tires, check that the
wheel nuts are still tight after driving 1000 miles (1600 km).
●
Be careful not to damage the aluminum wheels when using tire
chains.
●
Use only Toyota genuine balance weights or equivalent and a plas-
tic or rubber hammer when balancing your wheels.
■
When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning valve
and transmitters that allow the tire pressure warning system to provide
advance warning in the event of a loss in tire inflation pressure. When-
ever wheels are replaced, tire pressure warning valve and transmitters
must be installed. (
Wheels
If a wheel is bent, cracked or heavily corroded, it should be
replaced. Otherwise, the tire may separate from the wheel or
cause a loss of handling control.
Wheel selection
Aluminum wheel precautions (if equipped)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
465
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
WARNING
■
When replacing wheels
●
Do not use wheels that are a different size from those recommended in
the Owner’s Manual, as this may result in a loss of handling control.
●
Never use an inner tube in a leaking wheel which is designed for a
tubeless tire. Doing so may result in an accident, causing death or seri-
ous injury.
■
When installing the wheel nuts
●
Be sure to install the wheel nuts with the tapered ends facing inward.
(
P. 524) Installing the nuts with the tapered ends facing outward can
cause the wheel to break and eventually cause the wheel to come off
while driving, which could lead to an accident resulting in death or seri-
ous injury.
●
Never use oil or grease on the wheel bolts or wheel nuts.
Oil and grease may cause the wheel nuts to be excessively tightened,
leading to bolt or disc wheel damage. In addition, the oil or grease can
cause the wheel nuts to loosen and the wheel may fall off, causing an
accident and resulting in death or serious injury. Remove any oil or
grease from the wheel bolts or wheel nuts.
NOTICE
■
Replacing tire pressure warning valve and transmitters
●
Because tire repair or replacement may affect the tire pressure warn-
ing valve and transmitters, make sure to have tires serviced by your
Toyota dealer or other qualified service shop. In addition, make sure to
purchase your tire pressure warning valve and transmitters at your
Toyota dealer.
●
Ensure that only genuine Toyota wheels are used on your vehicle.
Tire pressure warning valve and transmitters may not work properly
with non-genuine wheels.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
466
6-3. Do-it-yourself maintenance
CAMRY_U
Turn the engine switch off.
Open the glove box and
remove the glove box cover
inside the glove box.
Remove the filter cover.
Unlock the filter cover.
Move the filter cover in the
direction of the arrow, and
then pull it out of the claws.
Remove the filter case.
There may be foreign objects on
top of the air conditioning filter.
Air conditioning filter
The air conditioning filter must be changed regularly to maintain
air conditioning efficiency.
Removal method
1
2
3
1
2
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
467
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Remove the air conditioning fil-
ter from the filter case and
replace it with a new one.
The “
UP” marks shown on the fil-
ter and the filter case should be
pointing up.
■
Checking interval
Inspect and replace the air conditioning filter according to the maintenance
schedule. In dusty areas or areas with heavy traffic flow, early replacement
may be required. (For scheduled maintenance information, please refer to the
“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)
■
If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace if necessary.
■
Air conditioning filter with deodorizing function
When fragrances are placed in your vehicle, the deodorizing effect may
become significantly weakened in a short period.
When an air conditioning odor comes out continuously, replace the air condi-
tioning filter.
5
NOTICE
■
When using the air conditioning system
Make sure that a filter is always installed.
Using the air conditioning system without a filter may cause damage to the
system.
■
To prevent damage to the filter cover
When moving the filter cover in the direc-
tion of arrow to release the fitting, pay
attention not to apply excessive force to
the claws. Otherwise, the claws may be
damaged.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
468
6-3. Do-it-yourself maintenance
CAMRY_U
●
Flathead screwdriver
●
Small flathead screwdriver
●
Lithium battery CR2032
Vehicles without a smart key system
Remove the key cover.
To prevent damage to the key,
cover the tip of the flathead screw-
driver with a rag.
Remove the battery cover.
If the battery cover is difficult to
remove, lift the edge to remove it.
Remove the depleted battery
using a small flathead screw-
driver.
Insert a new battery with the “+”
terminal facing up.
Wireless remote control/electronic key
battery
Replace the battery with a new one if it is depleted.
You will need the following items:
Replacing the battery
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
469
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Install the battery cover with the
tab facing up.
Push the entire edge of the battery
cover into the key.
Install the key cover.
Align the key cover with the key
and then press it straight into the
key.
Make sure that the key cover is
securely installed without any gaps
between it and the key.
Operate the
or
switch and check that the doors can
be locked/unlocked.
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
470
6-3. Do-it-yourself maintenance
CAMRY_U
Vehicles with a smart key system
Release the lock and remove
the mechanical key.
Remove the key cover.
To prevent damage to the key,
cover the tip of the flathead screw-
driver with a rag.
Remove the depleted battery
using a small flathead screw-
driver.
When removing the cover, the
electronic key module may stick to
the cover and the battery may not
be visible. In this case, remove the
electronic key module in order to
remove the battery.
Insert a new battery with the “+” terminal facing up.
When installing the key cover and mechanical key, install by con-
ducting
and
with the directions reversed.
Operate the
or
switch and check that the doors can
be locked/unlocked.
1
2
3
4
2
1
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
471
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
■
When replacing the key battery
Be careful not to lose the battery or any other small parts.
■
Use a CR2032 lithium battery
●
Batteries can be purchased at your Toyota dealer, local electrical appliance
shops or camera stores.
●
Replace only with the same or equivalent type recommended by the manu-
facturer.
●
Dispose of used batteries according to local laws.
■
If the key battery is depleted
The following symptoms may occur:
●
The smart key system (if equipped) and wireless remote control will not
function properly.
●
The operational range will be reduced.
WARNING
■
Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking.
Keep away from children. Failure to do so could result in death or serious
injury.
NOTICE
■
For normal operation after replacing the battery
Observe the following precautions to prevent accidents:
●
Always work with dry hands.
Moisture may cause the battery to rust.
●
Do not touch or move any other component inside the remote control.
●
Do not bend either of the battery terminals.
■
When removing the battery cover (vehicles without a smart key sys-
tem)
Do not forcibly remove the battery cover, otherwise it may be damaged.
If the battery cover is difficult to remove, lift the edge to remove it.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
472
6-3. Do-it-yourself maintenance
CAMRY_U
Turn the engine switch off.
Open the fuse box cover.
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as nec-
essary.
1
2
Engine compartment (type A)
Engine compartment (type B)
(if equipped)
Push the tabs in and lift the lid off.
Push the tabs in and lift the lid
off.
Under the driver’s side instru-
ment panel
Remove the lid.
Make sure to push the claw when
removing/installing the lid.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
473
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Remove the fuse with the pull-
out tool.
Only type A fuses can be removed
using the pullout tool.
Check if the fuse is blown.
Normal fuse
Blown fuse
Replace the blown fuse with a new fuse of an appropriate amperage rat-
ing. The amperage rating can be found on the fuse box lid.
3
4
Type A
Type B
Type C
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
474
6-3. Do-it-yourself maintenance
CAMRY_U
■
After a fuse is replaced
●
If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (
●
If the replaced fuse blows again, have the vehicle inspected by your Toyota
dealer.
■
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
WARNING
■
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
●
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
●
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
●
Do not modify the fuses or fuse boxes.
NOTICE
■
Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
475
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Check the wattage of the light bulb to be replaced. (
Light bulbs
You may replace the following bulbs yourself. The difficulty level
of replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact your Toyota
dealer.
For more information about replacing other light bulbs, contact
your Toyota dealer.
Preparing for light bulb replacement
Bulb locations
Front
Rear
Front turn signal/parking lights
(bulb type)
Front side marker lights (bulb
type)
Back-up lights (bulb type)
Rear turn signal lights (bulb
type)
Rear side marker lights (bulb
type)
1
2
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
476
6-3. Do-it-yourself maintenance
CAMRY_U
■
Front turn signal/parking lights (bulb type)
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.
Replacing light bulbs
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
477
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
■
Front side marker lights (bulb type)
To ensure enough space to
perform work, turn the steer-
ing wheel to move the front
wheel away from the light
bulb to be replaced.
Turn the steering wheel to the
left when replacing the right side
light bulb, and turn the steering
wheel to the right when replac-
ing the left side light bulb.
Remove the fender liner
clips.
To protect the front bumper
from being damaged, apply
protective tape around the
clip as shown in the illustra-
tion.
Use masking tape, etc. Do not
use duct tape, as it may leave
residue or damage the paint
when removed.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
478
6-3. Do-it-yourself maintenance
CAMRY_U
Insert a small flathead screw-
driver between the front
bumper and fender liner at
the position marked with a
“
” and then separate the
front bumper from the fender
liner.
To separate the front bumper
from the fender liner, pry up the
fender liner while pulling the
front bumper outward as shown
in the illustration.
Pull back the fender liner and
turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.
4
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
479
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Return the fender liner to its
original position, and install
the clips.
Make sure that the fender liner
is correctly positioned on the
inner side of the front bumper.
To Install the fender liner to
the front bumper, engage the
clip to the front bumper.
Remove the protective tape.
8
9
10
-------------------------------------------------------------------------------------------------------------------------------------------------------------
480
6-3. Do-it-yourself maintenance
CAMRY_U
■
Back-up lights (bulb type)
Open the trunk lid and
remove the clips.
Partly remove the trunk lid
cover.
Disconnect the connector
while depressing the lock
release. (When replacing
right side bulb only.)
Turn the bulb base counter-
clockwise.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
481
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Remove the light bulb.
Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.
Connect
the
connector.
(When replacing right side
bulb only.)
Reinstall the trunk lid cover
with the clips.
5
6
7
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
482
6-3. Do-it-yourself maintenance
CAMRY_U
■
Rear turn signal lights (bulb type) and rear side marker lights
(bulb type)
Open the trunk and apply
protective tape to the vehicle
body around the light unit.
Use masking tape, etc. Do not
use duct tape, as it may leave
residue or damage the paint
when removed.
Remove the cover.
Insert a flathead screw-
driver between the cover
and the light unit and pry
up the cover in several
positions as shown in the
illustration to disengage
the claws (indicated by a
dotted line).
Pull the cover toward the
rear of the vehicle to dis-
engage the claws (indi-
cated by a dotted line) and
remove the cover.
To prevent scratching the vehi-
cle, wrap the tip of the flathead
screwdriver with a cloth, etc.
Remove the 2 bolts.
1
2
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
483
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Remove the light unit.
Attach a long piece of
packing tape to the light
unit and fold the excess in
half.
Hold the folded portion
and pull it toward the rear
of the vehicle to remove
the light unit.
Turn the bulb base counterclockwise.
Remove the light bulb.
4
1
2
5
Rear turn signal lights
Rear side marker lights
6
Rear turn signal lights
Rear side marker lights
-------------------------------------------------------------------------------------------------------------------------------------------------------------
484
6-3. Do-it-yourself maintenance
CAMRY_U
Install a new light bulb and then install the bulb base to the light
unit by inserting it and turning it clockwise.
Install the light unit.
Align the tabs and push the light
unit toward the front of the vehi-
cle to install it.
Install the 2 bolts.
7
Rear turn signal lights
Rear side marker lights
8
9
-------------------------------------------------------------------------------------------------------------------------------------------------------------
485
6-3. Do-it-yourself maintenance
CAMRY_U
6
Mainten
ance an
d ca
re
Install the cover.
Remove the protective tape.
■
Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by
your Toyota dealer.
●
Headlights
●
Daytime running lights
●
Parking lights (LED type)
●
Front turn signal lights (LED type)
●
Front side marker lights (LED type)
●
Side turn signal lights (if equipped)
●
Tail lights
●
Rear side marker lights (LED type)
●
Stoplights
●
Rear turn signal lights (LED type)
●
Back-up lights (LED type)
●
High mounted stoplight
●
License plate lights
■
LED light bulbs
The lights other than the front turn signal/parking lights (bulb type), front side
marker lights (bulb type), back-up lights (bulb type), rear turn signal lights
(bulb type) and rear side marker lights (bulb type) consist of a number of
LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to
have the light replaced.
■
Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not
indicate a malfunction.
Contact your Toyota dealer for more information in the following situations:
●
Large drops of water have built up on the inside of the lens.
●
Water has built up inside the headlight.
10
11
-------------------------------------------------------------------------------------------------------------------------------------------------------------
486
6-3. Do-it-yourself maintenance
CAMRY_U
WARNING
■
Replacing light bulbs
●
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
●
Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth
to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
■
To prevent damage or fire
Make sure bulbs are fully seated and locked.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
487
7
When trouble arises
CAMRY_U
Emergency flashers . . .. 488
If your vehicle has
to be stopped in
an emergency . . . . . 489
or a warning buzzer
sounds . . . . . . . 500
If you have a flat tire. . .. 515
If the engine will not
not operate properly
(vehicles with a
smart key system). . ... 530
-------------------------------------------------------------------------------------------------------------------------------------------------------------
488
CAMRY_U
7-1. Essential information
Press the switch.
All the turn signal lights will flash.
To turn them off, press the switch
once again.
■
Emergency flashers
●
If the emergency flashers are used for a long time while the engine is not
operating, the battery may discharge.
●
If any of the SRS airbags deploy (inflate) or in the event of a strong rear
impact, the emergency flashers will turn on automatically.
The emergency flashers will turn off automatically after operating for approx-
imately 20 minutes. To manually turn the emergency flashers off, press the
switch twice.
(The emergency flashers may not turn on automatically depending on the
force of the impact and conditions of the collision.)
Emergency flashers
The emergency flashers are used to warn other drivers when the
vehicle has to be stopped on the road due to a breakdown, etc.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
489
7-1. Essential information
7
Wh
en tro
uble
a
ris
es
CAMRY_U
Steadily step on the brake pedal with both feet and firmly depress it.
Do not pump the brake pedal repeatedly as this will increase the effort
required to slow the vehicle.
Shift the shift lever to N.
If the shift lever is shifted to N
After slowing down, stop the vehicle in a safe place by the road.
Stop the engine.
If the shift lever cannot be shifted to N
Keep depressing the brake pedal with both feet to reduce vehicle
speed as much as possible.
Vehicles without a smart key
system: Stop the engine by
turning the engine switch to the
“ACC” position.
Vehicles with a smart key sys-
tem: To stop the engine, press
and hold the engine switch for 2
consecutive seconds or more,
or press it briefly 3 times or
more in succession.
Stop the vehicle in a safe place by the road.
If your vehicle has to be stopped in an
emergency
Only in an emergency, such as if it becomes impossible to stop
the vehicle in the normal way, stop the vehicle using the follow-
ing procedure:
1
2
3
4
3
4
Press and hold for 2 seconds or
more, or press briefly 3 times or more
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
490
7-1. Essential information
CAMRY_U
WARNING
■
If the engine has to be turned off while driving
●
Power assist for the brakes and steering wheel will be lost, making the
brake pedal harder to depress and the steering wheel heavier to turn.
Decelerate as much as possible before turning off the engine.
●
Vehicles without a smart key system: Never attempt to remove the key, as
doing so will lock the steering wheel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
491
7-1. Essential information
7
Wh
en tro
uble
a
ris
es
CAMRY_U
●
Remove the seat belt first.
●
If the door can be opened, open the door and exit the vehicle.
●
If the door cannot be opened, open the window using the power
window switch and exit the vehicle through the window.
●
If the window cannot be opened using the power window switch,
remain calm, wait until the water level inside the vehicle rises to the
point that the water pressure inside of the vehicle equals the water
pressure outside of the vehicle, and then open the door and exit the
vehicle.
If the vehicle is trapped in rising water
In the event the vehicle is submerged in water, remain calm and
perform the following.
WARNING
■
Using an emergency hammer
*
for emergency escape
The front side windows and rear side windows, as well as the rear window
can be shattered with an emergency hammer
*
used for emergency escape.
However, an emergency hammer
*
cannot shatter the windshield as it is
laminated glass.
*
: Contact your Toyota dealer or aftermarket accessory manufacturer for fur-
ther information about an emergency hammer.
■
Escaping the vehicle from the window
There are cases where escaping the vehicle from the window is not possi-
ble due to seating position, passenger body type, etc.
When using an emergency hammer, consider your seat location and the
size of the window opening to ensure that the opening is accessible and
large enough to escape.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
492
CAMRY_U
7-2. Steps to take in an emergency
If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle
towed by your Toyota dealer or commercial towing service,
using a wheel-lift type truck or flatbed truck.
Use a safety chain system for all towing, and abide by all state/
provincial and local laws.
2WD models: If towing your vehicle with a wheel-lift type truck
from the front, the vehicle's rear wheels and axles must be in
good conditions. (
If they are damaged, use a towing dolly or flatbed truck.
AWD models: If towing your vehicle with a wheel-lift type truck,
use a towing dolly. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
493
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
WARNING
Observe the following precautions.
Failure to do so may result in death or serious injury.
■
When towing the vehicle
2WD models
AWD models
■
While towing
●
When towing using cables or chains, avoid sudden starts, etc. which place
excessive stress on the towing eyelets, cables or chains. The towing eye-
lets, cables or chains may become damaged, broken debris may hit peo-
ple, and cause serious damage.
●
Vehicles without a smart key system: Do not turn the engine switch to the
“LOCK” position. There is a possibility that the steering wheel is locked
and cannot be operated.
●
Vehicles with a smart key system: Do not turn the engine switch off. There
is a possibility that the steering wheel is locked and cannot be operated
Be sure to transport the vehicle with the
front wheels raised or with all four wheels
raised off the ground. If the vehicle is
towed with the front wheels contacting
the ground, the drivetrain and related
parts may be damaged.
Be sure to transport the vehicle with all
four wheels raised off the ground. If the
vehicle is towed with the tires contacting
the ground, the drivetrain or related parts
may be damaged, the vehicle may fly off
the truck.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
494
7-2. Steps to take in an emergency
CAMRY_U
The following may indicate a problem with your transmission. Contact
your Toyota dealer or commercial towing service before towing.
●
The engine is running but the vehicle does not move.
●
The vehicle makes an abnormal sound.
NOTICE
■
To prevent damage to the vehicle when towing using a wheel-lift type
truck
●
Vehicles without a smart key system: Do not tow the vehicle from the rear
when the engine switch is in the “LOCK” position or the key is removed.
The steering lock mechanism is not strong enough to hold the front wheels
straight.
●
Vehicles with a smart key system: Do not tow the vehicle from the rear
when the engine switch is off. The steering lock mechanism is not strong
enough to hold the front wheels straight.
●
When raising the vehicle, ensure adequate ground clearance for towing at
the opposite end of the raised vehicle. Without adequate clearance, the
vehicle could be damaged while being towed.
■
To prevent damage to the vehicle when towing with a sling-type truck
Do not tow with a sling-type truck, either from the front or rear.
■
To prevent damage to the vehicle during emergency towing
Do not secure cables or chains to the suspension components.
■
Recreational towing (behind motor home, etc.)
Situations when it is necessary to contact dealers before towing
-------------------------------------------------------------------------------------------------------------------------------------------------------------
495
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
Towing with a wheel-lift type truck
From the front (2WD models)
From the front (AWD models)
Release the parking brake.
Vehicles with electric parking
brake: Turn automatic mode off.
(
Use a towing dolly under the rear
wheels.
From the rear
Use a towing dolly under the front
wheels.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
496
7-2. Steps to take in an emergency
CAMRY_U
NOTICE
■
Towing with a sling-type truck
Do not tow with a sling-type truck to prevent body damage.
2WD models
AWD models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
497
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
When using a flat-bed truck to transport the vehicle, use tire strapping
belts. Refer to the owner's manual of the flat-bed truck for the tire
strapping method.
Vehicles without a smart key system
In order to suppress vehicle movement during transportation, set the
parking brake and turn the engine switch to the “LOCK” position.
Vehicles with a smart key system
In order to suppress vehicle movement during transportation, set the
parking brake and turn the engine switch off.
A driver must be in the vehicle to steer and operate the brakes. The
vehicle's wheels, drive train, axles, steering and brakes must be in
good condition.
Using a flatbed truck
NOTICE
■
Using a flatbed truck
Do not overly tighten the tie downs or the vehicle may be damaged.
Emergency towing
-------------------------------------------------------------------------------------------------------------------------------------------------------------
498
7-2. Steps to take in an emergency
CAMRY_U
●
Fluid leaks under the vehicle.
(Water dripping from the air conditioning after use is normal.)
●
Flat-looking tires or uneven tire wear
●
Engine coolant temperature gauge needle continually points higher
than normal
●
Changes in exhaust sound
●
Excessive tire squeal when cornering
●
Strange noises related to the suspension system
●
Pinging or other noises related to the engine
●
Engine missing, stumbling or running roughly
●
Appreciable loss of power
●
Vehicle pulls heavily to one side when braking
●
Vehicle pulls heavily to one side when driving on a level road
●
Loss of brake effectiveness, spongy feeling, pedal almost touches
the floor
If you think something is wrong
If you notice any of the following symptoms, your vehicle proba-
bly needs adjustment or repair. Contact your Toyota dealer as
soon as possible.
Visible symptoms
Audible symptoms
Operational symptoms
-------------------------------------------------------------------------------------------------------------------------------------------------------------
499
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
Follow the procedure below to restart the engine after the system is
activated.
Vehicles without a smart key system
Turn the engine switch to the “ACC” or “LOCK” position.
Restart the engine.
Vehicles with a smart key system
Turn the engine switch off.
Restart the engine.
Fuel pump shut off system
To minimize the risk of fuel leakage when the engine stalls or
when an airbag inflates upon collision, the fuel pump shut off
system stops the supply of fuel to the engine.
NOTICE
■
Before starting the engine
Inspect the ground under the vehicle.
If you find that fuel has leaked onto the ground, the fuel system has been
damaged and is in need of repair. Do not restart the engine.
1
2
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
500
7-2. Steps to take in an emergency
CAMRY_U
If a warning light turns on or a warning
buzzer sounds
Calmly perform the following actions if any of the warning lights
comes on or flashes. If a light comes on or flashes, but then
goes off, this does not necessarily indicate a malfunction in the
system. However, if this continues to occur, have the vehicle
inspected by your Toyota dealer.
Warning light and warning buzzer list
Warning light
Warning light/Details/Actions
(U.S.A.)
(Red)
(Canada)
Brake system warning light
Indicates that:
• The brake fluid level is low; or
• The brake system is malfunctioning
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer. Continuing to drive the vehi-
cle may be dangerous.
(if equipped)
(Yellow)
Brake system warning light
Indicates a malfunction in the electric parking brake
Have the vehicle inspected by your Toyota dealer
immediately.
(U.S.A.)
(Canada)
Malfunction indicator lamp
Indicates a malfunction in:
• The electronic engine control system;
• The electronic throttle control system; or
• The electronic automatic transmission control system
Have the vehicle inspected by your Toyota dealer
immediately.
SRS warning light
Indicates a malfunction in:
• The SRS airbag system;
• The front passenger occupant classification system; or
• The seat belt pretensioner system
Have the vehicle inspected by your Toyota dealer
immediately.
(U.S.A.)
(Canada)
ABS warning light
Indicates a malfunction in:
• The ABS; or
• The brake assist system
Have the vehicle inspected by your Toyota dealer
immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
501
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
(Flashes)
(U.S.A.)
(Flashes)
(Canada)
Parking brake indicator (warning buzzer)
*
1
It is possible that the parking brake is not fully engaged or
released
Operate the parking brake once again.
This light comes on when the parking brake is not
released. If the light turns off after the parking brake is fully
released, the system is operating normally.
(if equipped)
(Flashes)
Brake hold operated indicator
Indicates a malfunction in the brake hold system
Have the vehicle inspected by your Toyota dealer
immediately.
(Red/yellow)
Electric power steering system warning light (warning
buzzer)
Indicates a malfunction in the EPS (Electric Power Steer-
ing) system
Have the vehicle inspected by your Toyota dealer
immediately.
(if equipped)
(Yellow)
LDA indicator
Indicates a malfunction in the LDA
When “LDA Unavailable” is displayed on the multi-
information display, turn the LDA system off, drive
the vehicle for a short time, and then turn the LDA
system back on. (
When a message other than above is displayed, fol-
low the instructions displayed in the message.
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
502
7-2. Steps to take in an emergency
CAMRY_U
(if equipped)
(Flashes or
illuminates)
PCS warning light
When a buzzer sounds simultaneously:
Indicates a malfunction has occurred in the PCS (Pre-Col-
lision System).
Have the vehicle inspected by your Toyota dealer
immediately.
When a buzzer does not sound:
The PCS (Pre-Collision System) has become temporarily
unavailable, corrective action may be necessary.
Follow the instructions displayed on the multi-infor-
mation display. (
If the PCS (Pre-Collision System) or VSC (Vehicle Stability
Control) system is disabled, the PCS warning light will illu-
minate.
(if equipped)
(Flashes)
ICS OFF indicator
When a buzzer sounds:
Indicates a malfunction in the Intelligent Clearance Sonar
system
Have the vehicle inspected by your Toyota dealer
immediately.
When a buzzer does not sound:
Indicates that the system is temporarily unavailable, possi-
bly due to a sensor being dirty or covered with ice, etc.
Clear the dirt, etc.
Slip indicator
Indicates a malfunction in:
• The VSC (Vehicle Stability Control) system;
• The TRAC (Traction Control) system; or
• The ABS
The light will flash when the VSC or the TRAC
system is
operating.
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
503
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
Low fuel level warning light
For 2WD models
L grade models: Indicates that remaining fuel is approxi-
mately 2.2 gal. (8.3L, 1.8 Imp. gal.)
Except for L grade models: Indicates that remaining fuel is
approximately 2.4 gal. (9.1L, 2.0 Imp. gal.)
For AWD models
Indicates that remaining fuel is approximately 2.2 gal.
(8.2L, 1.8 Imp. gal.)
Refuel the vehicle.
Driver’s and front passenger’s seat belt reminder light
(warning buzzer)
*
2
Warns the driver and/or front passenger to fasten their
seat belts
Fasten the seat belt.
If the front passenger’s seat is occupied, the front
passenger’s seat belt also needs to be fastened to
make the warning light (warning buzzer) turn off.
(Type A)
(Type B)
Rear passengers’ seat belt reminder lights (warning
buzzer)
*
2
Warns the rear passengers to fasten their seat belts.
Fasten the seat belt.
Master warning light
A buzzer sounds and the warning light comes on and
flashes to indicate that the master warning system has
detected a malfunction.
Tire pressure warning light
Indicates the following:
• Low tire pressure due to flat tire;
• Low tire pressure due to natural causes; or
• The tire pressure warning system is malfunctioning
Immediately stop the vehicle in a safe place.
Handling method (
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
504
7-2. Steps to take in an emergency
CAMRY_U
*
1
: Parking brake engaged warning buzzer:
A buzzer will sound if the vehicle is driven at a speed of approximately 3
mph (5 km/h) or more.
*
2
: Driver’s seat belt warning buzzer:
Vehicles without a smart key system:
The driver’s seat belt warning buzzer sounds to alert the driver that his or
her seat belt is not fastened. Once the engine switch is turned to the “ON”
position, the buzzer sounds. If the seat belt is still unfastened, the buzzer
sounds intermittently for a certain period of time after the vehicle reaches a
certain speed.
Vehicles with a smart key system:
The driver’s seat belt warning buzzer sounds to alert the driver that his or
her seat belt is not fastened. Once the engine switch is turned to IGNITION
ON mode, the buzzer sounds. If the seat belt is still unfastened, the buzzer
sounds intermittently for a certain period of time after the vehicle reaches a
certain speed.
Front passenger’s seat belt warning buzzer:
The front passenger’s seat belt warning buzzer sounds to alert the front
passenger that his or her seat belt is not fastened. If the seat belt is unfas-
tened, the buzzer sounds intermittently for a certain period of time after the
vehicle reaches a certain speed.
Rear passengers’ seat belt warning buzzer:
The rear passengers’ seat belt warning buzzer sounds to alert the rear
passenger that his or her seat belt is not fastened. If the seat belt is unfas-
tened, the buzzer sounds intermittently for a certain period of time, after
the seat belt is fastened and unfastened and the vehicle reaches a certain
speed.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
505
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
■
SRS warning light
This warning light system monitors the airbag sensor assembly, front impact
sensors, side impact sensors (front door), side impact sensors (front), side
impact sensors (rear), driver's seat position sensor, driver’s seat belt buckle
switch, front passenger occupant classification system (ECU and sensors),
“AIRBAG ON” indicator light, “AIRBAG OFF” indicator light, seat belt preten-
sioners, airbags, interconnecting wiring and power sources. (
■
Front passenger detection sensor, seat belt reminder and warning
buzzer
●
If luggage is placed on the front passenger seat, the front passenger detec-
tion sensor may cause the warning light to flash and the warning buzzer to
sound even if a passenger is not sitting in the seat.
●
If a cushion is placed on the seat, the sensor may not detect a passenger,
and the warning light may not operate properly.
■
If the malfunction indicator lamp comes on while driving
First check the following:
●
Is the fuel tank empty?
If it is, fill the fuel tank immediately.
●
Is the fuel tank cap loose?
If it is, tighten it securely.
The light will go off after several driving trips.
If the light does not go off even after several trips, contact your Toyota dealer
as soon as possible.
■
Electric power steering system warning light (warning buzzer)
When the battery charge becomes insufficient or the voltage temporarily
drops, the electric power steering system warning light may come on and the
warning buzzer may sound.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
506
7-2. Steps to take in an emergency
CAMRY_U
■
When the tire pressure warning light comes on
Inspect the tires to check if a tire is punctured.
If a tire is punctured:
If none of the tires are punctured:
Turn the engine switch off then turn it to the “ON” position (vehicle without
a smart key system) or IGNITION ON mode (vehicle with a smart key
system). Check if the tire pressure warning light comes on or blinks.
If the tire pressure warning light comes on
After the temperature of the tires has lowered sufficiently, check the
inflation pressure of each tire and adjust them to the specified level.
If the warning light does not turn off even after several minutes have
elapsed, check that the inflation pressure of each tire is at the specified
level and perform initialization. (
If the warning light does not turn off several minutes after the initialization
has been performed, have the vehicle inspected by your Toyota dealer
immediately.
If the tire pressure warning light blinks for 1 minute then stays on
There may be a malfunction in the tire pressure warning system. Have
the vehicle inspected by your Toyota dealer immediately.
■
The tire pressure warning light may come on due to natural causes
The tire pressure warning light may come on due to natural causes such
as natural air leaks and tire inflation pressure changes caused by tem-
perature. In this case, adjusting the tire inflation pressure will turn off the
warning light (after a few minutes).
■
When a tire is replaced with a spare tire
The compact spare tire is not equipped with a tire pressure warning valve
and transmitter. If a tire goes flat, the tire pressure warning light will not
turn off even though the flat tire has been replaced with the spare tire.
Replace the spare tire with the repaired tire and adjust the tire inflation
pressure. The tire pressure warning light will go off after a few minutes.
■
Conditions that the tire pressure warning system may not function
properly
■
Warning buzzer
In some cases, the buzzer may not be heard because of noisy place or an
audio sound.
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
507
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
WARNING
■
If both the ABS and the brake system warning lights remain on
Stop your vehicle in a safe place immediately and contact your Toyota
dealer. The vehicle will become extremely unstable during braking, and the
ABS system may fail, which could cause an accident resulting in death or
serious injury.
■
When the electric power steering system warning light comes on
When the light comes on yellow, the assist to the power steering is
restricted. When the light comes on red, the assist to the power steering is
lost and handling operations of the steering wheel become extremely
heavy. When steering wheel operations are heavier than usual, grip the
steering wheel firmly and operate it using more force than usual.
■
If the tire pressure warning light comes on
Be sure to observe the following precautions. Failure to do so could
cause a loss of vehicle control and result in death or serious injury.
●
Stop your vehicle in a safe place as soon as possible. Adjust the tire
inflation pressure immediately.
●
If the tire pressure warning light comes on even after tire inflation pres-
sure adjustment, it is probable that you have a flat tire. Check the tires.
If a tire is flat, change it with the spare tire and have the flat tire
repaired by the nearest Toyota dealer.
●
Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate,
you could lose control of the steering wheel or the brakes.
■
If a blowout or sudden air leakage should occur
The tire pressure warning system may not activate immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
508
7-2. Steps to take in an emergency
CAMRY_U
WARNING
■
Maintenance of the tires
Each tire, including the spare (if provided), should be checked monthly
when cold and inflated to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or tire inflation pressure
label (tire and load information label). (If your vehicle has tires of a dif-
ferent size than the size indicated on the vehicle placard or tire inflation
pressure label [tire and load information label], you should determine
the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped with a tire
pressure monitoring system (TPMS-tire pressure warning system) that
illuminates a low tire pressure telltale (tire pressure warning light) when
one or more of your tires is significantly under-inflated. Accordingly,
when the low tire pressure telltale (tire pressure warning light) illumi-
nates, you should stop and check your tires as soon as possible, and
inflate them to the proper pressure. Driving on a significantly under-
inflated tire causes the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire tread life, and may
affect the vehicle’s handling and stopping ability.
Please note that the TPMS (tire pressure warning system) is not a sub-
stitute for proper tire maintenance, and it is the driver’s responsibility to
maintain correct tire pressure, even if under-inflation has not reached
the level to trigger illumination of the TPMS low tire pressure telltale (tire
pressure warning light).
Your vehicle has also been equipped with a TPMS (tire pressure warn-
ing system) malfunction indicator to indicate when the system is not
operating properly. The TPMS (tire pressure warning system) malfunc-
tion indicator is combined with the low tire pressure telltale (tire pressure
warning light). When the system detects a malfunction, the telltale will
flash for approximately one minute and then remain continuously illumi-
nated. This sequence will continue upon subsequent vehicle start-ups
as long as the malfunction exists. When the malfunction indicator is illu-
minated, the system may not be able to detect or signal low tire pres-
sure as intended.
TPMS (tire pressure warning system) malfunctions may occur for a vari-
ety of reasons, including the installation of replacement or alternate tires
or wheels on the vehicle that prevent the TPMS (tire pressure warning
system) from functioning properly. Always check the TPMS (tire pres-
sure warning system) malfunction telltale after replacing one or more
tires or wheels on your vehicle to ensure that the replacement or alter-
nate tires and wheels allow the TPMS (tire pressure warning system) to
continue to function properly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
509
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
NOTICE
■
To ensure the tire pressure warning system operates properly
Do not install tires with different specifications or makers, as the tire
pressure warning system may not operate properly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
510
7-2. Steps to take in an emergency
CAMRY_U
Master warning light
The master warning light also comes on or flashes in order to indicate that
a message is currently being displayed on the multi-information display.
Multi-information display
Handling method
Follow the instructions of the message on the multi-information display.
If any of the warning messages are shown again after the appropriate
actions have been performed, contact your Toyota dealer.
If a warning message is displayed
The multi-information display shows warnings of system mal-
functions, incorrectly performed operations, and messages that
indicate a need for maintenance. When a message is shown,
perform the correction procedure appropriate to the message.
4.2-inch display
7-inch display
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
511
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
The warning lights and warning buzzers operate as follows depending
on the content of the message. If a message indicates the need for
inspection by a dealer, have the vehicle inspected by your Toyota
dealer immediately.
The operation of the warning lights and warning buzzers may differ
from those stated. In this case, perform the correction procedure
according to the displayed message.
*
: A buzzer sounds the first time a message is shown on the multi-informa-
tion display.
Messages and warnings
System
warning
light
Warning buzzer
*
Warning
Comes
on
Sounds
Indicates an important situation,
such as when a system related to
driving is malfunctioning or that
danger may result if the correction
procedure is not performed
Comes
on or
flashes
Sounds
Indicates an important situation,
such as when the systems shown
on the multi-information display
may be malfunctioning
Flashes
Sounds
Indicates a situation, such as
when damage to the vehicle or
danger may result
Comes
on
Does not sound
Indicates a condition, such as mal-
function of electrical components,
their condition, or indicates the
need for maintenance
Flashes
Does not sound
Indicates a situation, such as
when an operation has been per-
formed incorrectly, or indicates
how to perform an operation cor-
rectly
-------------------------------------------------------------------------------------------------------------------------------------------------------------
512
7-2. Steps to take in an emergency
CAMRY_U
■
Warning messages
The warning messages explained below may differ from the actual messages
according to operation conditions and vehicle specifications.
■
System warning lights
The master warning light does not come on or flash in the following cases.
Instead, a separate system warning light will come on along with a message
shown on the multi-information display.
●
Malfunction in the ABS
The ABS warning light comes on. (
●
Malfunction in the tire pressure warning system
The tire pressure warning light comes on. (
●
Remaining fuel level is low
The low fuel level warning light comes on. (
■
If a message instructing to refer to the Owner’s Manual is displayed
●
If the following messages are shown, there may be a malfunction.
Immediately stop the vehicle in a safe place and contact your Toyota dealer.
Continuing to drive the vehicle may be dangerous.
• “Low Braking Power Stop in a Safe Place See Owner’s Manual”
• “Oil Pressure Low Stop in a Safe Place See Owner’s Manual”
• “Charging System Malfunction Stop in a Safe Place See Owner’s Man-
ual”
●
If the following message is shown, there may be a malfunction.
Immediately have the vehicle inspected by your Toyota dealer.
• “Smart Key System Malfunction See Owner’s Manual”
●
If “Engine Coolant Temp High Stop in a Safe Place See Owner’s Manual” is
displayed, follow the instructions accordingly. (
■
If “Shift to P Before Exiting Vehicle” is shown
Message is displayed when the driver’s door is opened without turning the
engine switch off with the shift lever in any position other than P.
Shift the shift lever to P.
■
If “Auto Power Off to Conserve Battery” is displayed
This message is displayed when the power was cut off due to the automatic
power off function.
The next time the engine is started, increase the engine speed slightly and
maintain it at that speed for approximately 5 minutes to recharge the battery.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
513
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
■
If “A New Key has been Registered Contact Your Dealer for Details” is
displayed (if equipped)
This message will be displayed each time the driver’s door is opened when
the doors are unlocked from the outside for approximately one week after a
new electronic key has been registered.
If this message is displayed but you have not had a new electronic key regis-
tered, ask your Toyota dealer to check if an unknown electronic key (other
than those in your possession) has been registered.
■
If “Headlight System Malfunction Visit Your Dealer” is displayed
The following systems may be malfunctioning. Have the vehicle inspected by
your Toyota dealer immediately.
●
The LED headlight system
●
Automatic High Beam (if equipped)
■
If a message that indicates the malfunction of front camera is displayed
(if equipped)
The following systems may be suspended until the problem shown in the
message is resolved. (
●
PCS (Pre-Collision System)
●
LDA (Lane Departure Alert with steering control)
●
Dynamic radar cruise control with full-speed range
●
Dynamic radar cruise control
●
Automatic High Beam
■
If “Maintenance Required Soon” is displayed (if equipped)
Indicates that all maintenance according to the driven distance on the mainte-
nance schedule
*
should be performed soon.
Comes on approximately 4500 miles (7200 km) after the message has been
reset.
If necessary, perform maintenance. Please reset the message after the main-
tenance is performed. (
*
: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
514
7-2. Steps to take in an emergency
CAMRY_U
■
If “Maintenance Required Visit Your Dealer” is displayed (if equipped)
Indicates that all maintenance is required to correspond to the driven distance
on the maintenance schedule
*
.
Comes on approximately 5000 miles (8000 km) after the message has been
reset.
(The indicator will not work properly unless the message has been reset.)
Perform the necessary maintenance. Please reset the message after the
maintenance is performed. (
*
: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
■
If “Engine Oil Level Low Add or Replace” is displayed
The engine oil level may be low. Check the level of the engine oil, and add
engine oil if necessary. This message may be displayed if the vehicle is
stopped on a slope. Move the vehicle to a level surface and check if the mes-
sage disappears.
■
Warning buzzer
NOTICE
■
If “High Power Consumption Power to Climate Temporarily Limited” is
frequently shown
There is a possible malfunction relating to the charging system or the bat-
tery may be deteriorating. Have the vehicle inspected by your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
515
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
●
Stop the vehicle in a safe place on a hard, flat surface.
●
Set the parking brake.
●
Shift the shift lever to P.
●
Stop the engine.
●
Turn on the emergency flashers. (
If you have a flat tire
Your vehicle is equipped with a spare tire. The flat tire can be
replaced with the spare tire.
For details about tires:
WARNING
■
If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair, which could result in an accident.
Before jacking up the vehicle
-------------------------------------------------------------------------------------------------------------------------------------------------------------
516
7-2. Steps to take in an emergency
CAMRY_U
2WD models
AWD models
Location of the spare tire, jack and tools
Luggage floor cover
Wheel nut wrench
Jack
Spare tire
Jack handle
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
517
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
WARNING
■
Using the tire jack
Observe the following precautions.
Improper use of the tire jack may cause the vehicle to suddenly fall off
the jack, leading to death or serious injury.
●
Do not use the tire jack for any purpose other than replacing tires or
installing and removing tire chains.
●
Only use the tire jack that comes with this vehicle for replacing a flat
tire.
Do not use it on other vehicles, and do not use other tire jacks for
replacing tires on this vehicle.
●
Put the jack properly in its jack point.
●
Do not put any part of your body under the vehicle while it is supported
by the jack.
●
Do not start the engine or drive the vehicle while the vehicle is sup-
ported by the jack.
●
Do not raise the vehicle while someone is inside.
●
When raising the vehicle, do not put an object on or under the jack.
●
Do not raise the vehicle to a height greater than that required to
replace the tire.
●
Use a jack stand if it is necessary to get under the vehicle.
●
When lowering the vehicle, make sure that there is no-one near the
vehicle. If there are people nearby, warn them vocally before lowering.
NOTICE
■
To prevent damage to the vehicle when using a jack
When jacking up the rear of the vehi-
cle, make sure not to position the jack
under the bracket shown in the illustra-
tion near the rear jack point, as the
vehicle body may be damaged.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
518
7-2. Steps to take in an emergency
CAMRY_U
Lift up the hook of the luggage
floor cover on the trunk floor.
Secure the luggage floor cover
using the hook provided.
Remove the jack.
Taking out the jack
1
2
3
2WD models
AWD models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
519
7-2. Steps to take in an emergency
CAMRY_U
7
Wh
en tro
uble
a
ris
es
Lift up the hook of the luggage
floor cover on the trunk floor.
Secure the luggage floor cover
using the hook provided.
Remove the tool tray.
Taking out the spare tire
1
2
3
2WD models
AWD models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст