Toyota Prius Prime (2020 year). Owner's manual — part 43
680
8-2. Steps to take in an emergency
If you have a flat tire
Your vehicle is not equipped with a spare tire, but instead is
equipped with an emergency tire puncture repair kit.
A puncture caused by a nail or screw passing through the tire
tread can be repaired temporarily using the emergency tire
puncture repair kit. (The kit contains a bottle of sealant. The
sealant can be used only once to temporarily repair one tire
without removing the nail or screw from the tire.) After temporar-
ily repairing the tire with the kit, have the tire repaired or
replaced by your Toyota dealer.
WARNING
■
If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair, which could result in an accident.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
681
8-2. Steps to take in an emergency
8
Wh
en tro
● Stop the vehicle in a safe place on a hard, flat surface.
● Set the parking brake.
● Shift the shift position to P.
● Stop the hybrid system.
● Turn on the emergency flashers.
● Check the degree of the tire damage.
A tire should only be repaired
with the emergency tire punc-
ture repair kit if the damage is
caused by a nail or screw pass-
ing through the tire tread.
• Do not remove the nail or
screw from the tire. Remov-
ing the object may widen the
opening and make emer-
gency repair with the repair
kit impossible.
• To avoid sealant leakage, move the vehicle until the area of the
puncture, if known, is positioned at the top of the tire.
■
A flat tire that cannot be repaired with the emergency tire puncture
repair kit
In the following cases, the tire cannot be repaired with the emergency tire
puncture repair kit. Contact your Toyota dealer.
●
When the tire is damaged due to driving without sufficient air pressure
●
When there are any cracks or damage at any location on the tire, such
as on the side wall, except the tread
●
When the tire is visibly separated from the wheel
●
When the cut or damage to the tread is 0.16 in. (4 mm) long or more
●
When the wheel is damaged
●
When two or more tires have been punctured
●
When more than one sharp objects such as nails or screws have passed
through the tread on a single tire
●
When the sealant has expired
Before repairing the tire
-------------------------------------------------------------------------------------------------------------------------------------------------------------
682
8-2. Steps to take in an emergency
Emergency tire puncture repair kit
Location of the emergency tire puncture repair kit
-------------------------------------------------------------------------------------------------------------------------------------------------------------
683
8-2. Steps to take in an emergency
8
Wh
en tro
Emergency tire puncture repair kit components
Hose
Air release cap
Sticker
Power plug
Air pressure gauge
Compressor switch
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
684
8-2. Steps to take in an emergency
Pull the strap up and remove
the cover.
Take out the emergency tire
puncture repair kit.
■
When installing the cover
Taking out the emergency tire puncture repair kit
1
2
Insert the claw in to the hole, and return
the cover.
IO82PH048
-------------------------------------------------------------------------------------------------------------------------------------------------------------
685
8-2. Steps to take in an emergency
8
Wh
en tro
Take out the repair kit from the plastic bag.
Remove the valve cap from the
valve of the punctured tire.
Extend the hose. Remove the
air release cap from the hose.
Attach the sticker enclosed with
the bottle on the specified loca-
tions. (See step
.)
You will use the air release cap
again. Therefore keep it in a safe
place.
Connect the hose to the valve.
Screw the end of the hose clock-
wise as far as possible.
Make sure that the compressor
switch is off.
Emergency repair method
1
2
3
10
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
686
8-2. Steps to take in an emergency
Lift the rubber stopper on the
compressor.
Remove the power plug from
the compressor.
Connect the power plug to the
power outlet socket. (
6
7
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
687
8-2. Steps to take in an emergency
8
Wh
en tro
Connect the bottle to the com-
pressor.
As shown in the illustration, insert
the bottle securely into the com-
pressor until the upper side of the
mark on the bottle is aligned with
the upper end of the notch.
Attach the sticker provided with
the tire puncture repair kit to a
position easily seen from the
driver’s seat.
Check the specified tire inflation
pressure.
Tire inflation pressure is specified
on the label on the driver’s side
pillar as shown. (
Start the hybrid system. (
P. 336)
9
(U.S.A.)
(Canada)
10
11
12
-------------------------------------------------------------------------------------------------------------------------------------------------------------
688
8-2. Steps to take in an emergency
To inject the sealant and inflate
the tire, turn the compressor
switch on.
Inflate the tire until the specified air pressure is reached.
The sealant will be injected
and the pressure will spike to
between 44 psi (300 kPa,
3.0 kgf/cm
2
or bar) and
58 psi (400 kPa, 4.0 kgf/cm
2
or bar), then gradually
decrease.
The air pressure gauge will
display the actual tire infla-
tion pressure about 1 to 5
minutes after the switch is
turned on.
• Turn the compressor switch
off and then check the tire
inflation
pressure.
Being
careful not to over inflate,
check and repeat the inflation
procedure until the specified
tire inflation pressure is
reached.
• The tire can be inflated for about 5 to 20 minutes (depending on
the outside temperature). If the tire inflation pressure is still lower
than the specified point after inflation for 25 minutes, the tire is
too damaged to be repaired. Turn the compressor switch off and
contact your Toyota dealer.
• If the tire inflation pressure exceeds the specified air pressure, let
out some air to adjust the tire inflation pressure. (
13
14
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
689
8-2. Steps to take in an emergency
8
Wh
en tro
With the compressor switch off, disconnect the hose from the valve
on the tire and then pull out the power plug from the power outlet
socket.
Some sealant may leak when the hose is removed.
Install the valve cap onto the valve of the emergency repaired tire.
Attach the air release cap to the
end of the hose.
If the air release cap is not
attached, the sealant may leak
and the vehicle may get dirty.
Temporarily store the bottle in the luggage compartment while it is
connected to the compressor.
To spread the liquid sealant evenly within the tire, immediately drive
safely for about 3 miles (5 km) below 50 mph (80 km/h).
After driving, stop your vehicle
in a safe place on a hard, flat
surface and reconnect the
repair kit.
Remove the air release cap from
the hose before reconnecting the
hose.
15
16
17
18
19
20
-------------------------------------------------------------------------------------------------------------------------------------------------------------
690
8-2. Steps to take in an emergency
Turn the compressor switch on and wait for several seconds, then
turn it off. Check the tire inflation pressure.
If the tire inflation pressure is
under
19 psi
(130 kPa,
1.3 kgf/cm
2
or bar): The
puncture cannot be repaired.
Contact your Toyota dealer.
If the tire inflation pressure is
19 psi (130 kPa, 1.3 kgf/cm
2
or bar) or higher, but less
than the specified air pres-
sure: Proceed to step
.
If the tire inflation pressure is the specified air pressure (
P. 725):
Proceed to step
.
Turn the compressor switch on to inflate the tire until the specified
air pressure is reached. Drive for about 3 miles (5 km) and then
perform step
.
Attach the air release cap to the
end of the hose.
If the air release cap is not
attached, the sealant may leak
and the vehicle may get dirty.
Store the bottle in the luggage compartment while it is connected to
the compressor.
Taking precautions to avoid sudden braking, sudden acceleration
and sharp turns, drive carefully at under 50 mph (80 km/h) to the
nearest Toyota dealer that is less than 62 miles (100 km) away for
tire repair or replacement.
When having the tire repaired or replaced, make sure to tell the Toyota
dealer that the sealant is injected.
21
1
2
22
3
23
22
20
23
24
25
-------------------------------------------------------------------------------------------------------------------------------------------------------------
691
8-2. Steps to take in an emergency
8
Wh
en tro
■
If the tire is inflated to more than the specified air pressure
Disconnect the hose from the valve.
Disconnect the hose from the valve, remove the air release cap from
the hose and then reconnect the hose.
Turn the compressor switch on and wait for several seconds, and then
turn it off. Check that the air pressure indicator shows the specified air
pressure. (
If the air pressure is under the designated pressure, turn the compres-
sor switch on again and repeat the inflation procedure until the speci-
fied air pressure is reached.
■
The valve of a tire that has been repaired
After a tire is repaired with the emergency tire puncture repair kit, the
valve should be replaced.
■
After a tire is repaired with the emergency tire puncture repair kit
●
The tire pressure warning valve and transmitter should be replaced.
●
Even if the tire inflation pressure is at the recommended level, the tire
pressure warning light may come on/flash.
■
Note for checking the emergency tire puncture repair kit
Check the sealant expiry date occasionally.
The expiry date is shown on the bottle. Do not use sealant whose expiry
date has already passed. Otherwise, repairs conducted using the emer-
gency tire puncture repair kit may not be performed properly.
Install the air release cap to the end of
the hose and push the protrusion on
the air release cap into the tire valve
to let some air out.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
692
8-2. Steps to take in an emergency
■
Emergency tire puncture repair kit
●
The emergency tire puncture repair kit is for filling the car tire with air.
●
The sealant has a limited life span. The expiry date is marked on the
bottle. The sealant should be replaced before the expiry date. Contact
your Toyota dealer for replacement.
●
The sealant stored in the emergency tire puncture repair kit can be used
only once to temporarily repair a single tire. If the sealant in the bottle
and other parts of the kit have been used and need to be replaced, con-
tact your Toyota dealer.
●
The compressor can be used repeatedly.
●
The sealant can be used when the outside temperature is from -40°F
(-40°C) to 140°F (60°C).
●
The kit is exclusively designed for size and type of tires originally
installed on your vehicle. Do not use it for tires that a different size than
the original ones, or for any other purposes.
●
If the sealant gets on your clothes, it may stain.
●
If the sealant adheres to a wheel or the surface of the vehicle body, the
stain may not be removable if it is not cleaned at once. Immediately wipe
away the sealant with a wet cloth.
●
During operation of the repair kit, a loud operation noise is produced.
This does not indicate a malfunction.
●
Do not use to check or to adjust the tire pressure.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
693
8-2. Steps to take in an emergency
8
Wh
en tro
WARNING
■
Do not drive the vehicle with a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair.
Driving with a flat tire may cause a circumferential groove on the side
wall. In such a case, the tire may explode when using a repair kit.
■
Caution while driving
●
Store the repair kit in the luggage compartment.
Injuries may result in the event of an accident or sudden braking.
●
The repair kit is exclusively only for your vehicle.
Do not use repair kit on other vehicles, which could lead to an accident
causing death or serious injury.
●
Do not use repair kit for tires that are different size than the original
ones, or for any other purpose. If the tires have not been completely
repaired, it could lead to an accident causing death or serious injury.
■
Precautions for use of the sealant
●
Ingesting the sealant is hazardous to your health. If you ingest sealant,
consume as much water as possible, and then immediately consult a
doctor.
●
If sealant gets in eyes or adheres to skin, immediately wash it off with
water. If discomfort persists, consult a doctor.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
694
8-2. Steps to take in an emergency
WARNING
■
When fixing the flat tire
●
Stop your vehicle in a safe and flat area.
●
Do not touch the wheels or the area around the brakes immediately
after the vehicle has been driven.
After the vehicle has been driven, the wheels and the area around the
brakes may be extremely hot. Touching these areas with hands, feet or
other body parts may result in burns.
●
Connect the valve and hose securely with the tire installed on the vehi-
cle. If the hose is not properly connected to the valve, air leakage may
occur as sealant may be sprayed out.
●
If the hose comes off the valve while inflating the tire, there is a risk
that the hose will move abruptly due to air pressure.
●
After inflation of the tire has completed, the sealant may splatter when
the hose is disconnected or some air is let out of the tire.
●
Follow the operation procedure to repair the tire. If the procedures not
followed, the sealant may spray out.
●
Keep back from the tire while it is being repaired, as there is a chance
of it bursting while the repair operation is being performed. If you
notice any cracks or deformation of the tire, turn off the compressor
switch and stop the repair operation immediately.
●
The repair kit may overheat if operated for a long period of time. Do not
operate the repair kit continuously for more than 40 minutes.
●
Parts of the repair kit become hot during operation. Be careful handling
the repair kit during and after operation. Do not touch the metal part
connecting the bottle and the compressor. It will be extremely hot.
●
Do not attach the vehicle speed warning sticker to an area other than
the one indicated. If the sticker is attached to an area where an SRS
airbag is located, such as the pad of the steering wheel, it may prevent
the SRS airbag from operating properly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
695
8-2. Steps to take in an emergency
8
Wh
en tro
WARNING
■
Driving to spread the liquid sealant evenly
Observe the following precautions to reduce the risk of accidents.
Failing to do so may result in a loss of vehicle control and cause death
or serious injury.
●
Drive the vehicle carefully at a low speed. Be especially careful when
turning and cornering.
●
If the vehicle does not drive straight or you feel a pull through the
steering wheel, stop the vehicle and check the following.
• Tire condition. The tire may have separated from the wheel.
• Tire inflation pressure. If the tire inflation pressure is 19 psi
(130 kPa, 1.3 kgf/cm
2
or bar) or less, the tire may be severely dam-
aged.
NOTICE
■
When performing an emergency repair
●
A tire should only be repaired with the emergency tire puncture repair
kit if the damage is caused by a sharp object such as nail or screw
passing through the tire tread.
Do not remove the sharp object from the tire. Removing the object may
widen the opening and disenable emergency repair with the repair kit.
●
The repair kit is not waterproof. Make sure that the repair kit is not
exposed to water, such as when it is being used in the rain.
●
Do not put the repair kit directly onto dusty ground such as sand at the
side of the road. If the repair kit vacuums up dust etc., a malfunction
may occur.
■
Precautions for the emergency tire puncture repair kit
●
The repair kit power source should be 12 V DC suitable for vehicle
use. Do not connect the repair kit to any other source.
●
If fuel splatters on the repair kit, the repair kit may deteriorate. Take
care not to allow fuel to contact it.
●
Place the repair kit in a storage to prevent it from being exposed to dirt
or water.
●
Store the repair kit in the luggage compartment out of reach of chil-
dren.
●
Do not disassemble or modify the repair kit. Do not subject parts such
as the air pressure indicator to impacts. This may cause a malfunction.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст