Toyota Prius (2021 year). Manual in english — part 10
592
PRIUS_OM_OM47E09U_(U)
7-2. Steps to take in an emergency
If a warning light turns on or a warning
buzzer sounds
Calmly perform the following actions if any of the warning lights
comes on or flashes. If a light comes on or flashes, but then
goes off, this does not necessarily indicate a malfunction in the
system. However, if this continues to occur, have the vehicle
inspected by your Toyota dealer.
Warning light and warning buzzer list
Warning light
Warning light/Details/Actions
(U.S.A.)
(Canada)
Brake system warning light and warning buzzer (red
indicator)
*
1
Indicates that:
• The brake fluid level is low; or
• The brake system is malfunctioning
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer. Continuing to drive the vehi-
cle may be dangerous.
Brake system warning light (yellow indicator)
Indicates a malfunction in:
• The regenerative braking system; or
• The electronically controlled brake system
Have the vehicle inspected by your Toyota dealer
immediately.
Charging system warning light
Indicates a malfunction in the vehicle’s charging system
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer.
Low engine oil pressure warning light
(warning buzzer)
*
2
Indicates that the engine oil pressure is too low
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer.
(U.S.A.)
(Canada)
Malfunction indicator lamp
Indicates a malfunction in:
• The hybrid system;
• The electronic engine control system; or
• The electronic throttle control system
Have the vehicle inspected by your Toyota dealer
immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
593
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
SRS warning light
Indicates a malfunction in:
• The SRS airbag system;
• The front passenger occupant classification system; or
• The seat belt pretensioner system
Have the vehicle inspected by your Toyota dealer
immediately.
(U.S.A.)
(Canada)
ABS warning light
Indicates a malfunction in:
• The ABS; or
• The brake assist system
Have the vehicle inspected by your Toyota dealer
immediately.
(Red/yellow)
Electric power steering system warning light (warning
buzzer)
Indicates a malfunction in the EPS (Electric Power Steer-
ing) system
Have the vehicle inspected by your Toyota dealer
immediately.
(Flashes or
illuminates)
(If equipped)
PCS warning light
• When a buzzer sounds simultaneously:
Indicates a malfunction has occurred in the PCS (Pre-
Collision System).
Have the vehicle inspected by your Toyota dealer
immediately.
• When a buzzer does not sound:
The PCS (Pre-Collision System) has become temporar-
ily unavailable, corrective action may be necessary.
Follow the instructions displayed on the multi-infor-
mation display. (
If the PCS (Pre-Collision System) or VSC (Vehicle Stability
Control) system is disabled, the PCS warning light will illu-
minate.
(Orange)
(If equipped)
LTA indicator (warning buzzer)
Indicates a malfunction in the LTA (Lane Tracing Assist)
Follow the instructions displayed on the multi-infor-
mation display. (
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
594
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Slip indicator light
Indicates a malfunction in:
• The VSC system;
• The TRAC system; or
• The hill-start assist control system
Have the vehicle inspected by your Toyota dealer
immediately.
The light will flash when the ABS, VSC or TRAC system is
operating.
High coolant temperature warning light
• When the light flashes:
Indicates that the engine coolant temperature is too high
The light changes from a flashing to a solid light when
the temperature further increases
Immediately stop the vehicle in a safe place. (
• When the light comes on without flashing:
Indicates a malfunction in the exhaust heat recirculator
system
Have the vehicle inspected by your Toyota dealer
immediately.
(Flashes)
(If equipped)
PKSB OFF indicator
Indicates a malfunction in the Parking Support Brake func-
tion
Have the vehicle inspected by your Toyota dealer.
The warning light will operate as follows, even when the
system is not malfunctioning:
• The light will come on when the Parking Support Brake
function is turned off (
• The light will come on when the Parking Support Brake
function is operating (
• The light will flash when the system cannot be temporar-
ily used (
Open door warning light (warning buzzer)
*
3
Indicates that a door is not fully closed
Check that all the doors are closed.
Low fuel level warning light
Indicates that remaining fuel is approximately 1.7 gal.
(6.4 L, 1.4 Imp.gal.) or less
Refuel the vehicle.
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
595
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Driver’s and front passenger’s seat belt reminder light
(warning buzzer)
*
4
Warns the driver and/or front passenger to fasten their
seat belts
Fasten the seat belt.
If the front passenger’s seat is occupied, the front
passenger’s seat belt also needs to be fastened to
make the warning light (warning buzzer) turn off.
(U.S.A.)
(Canada)
Rear passengers’ seat belt reminder lights (warning
buzzer)
*
5
Warns the rear passengers to fasten their seat belts
Fasten the seat belt.
Master warning light
A buzzer sounds and the warning light comes on and
flashes to indicate that the master warning system has
detected a malfunction.
Tire pressure warning light
When the light comes on:
Low tire inflation pressure such as
• Natural causes (
• Flat tire (
Adjust the tire inflation pressure to the specified
level.
The light will turn off after a few minutes. In case
the light does not turn off even if the tire inflation
pressure is adjusted, have the system checked by
your Toyota dealer.
When the light comes on after blinking for 1 minute:
Malfunction in the tire pressure warning system
(
Have the system checked by your Toyota dealer.
(Flashes)
(If equipped)
“AFS OFF” indicator
Indicates a malfunction in the adaptive front-lighting sys-
tem
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
596
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Brake Override System/Drive-Start Control/
Parking Support Brake function (symbol display)
*
6
Brake Override System
Indicates that the accelerator and brake pedals are being
depressed simultaneously, and the Brake Override Sys-
tem is operating
Release the accelerator pedal and depress the brake
pedal.
Indicates a malfunction in the Brake Override System
(with warning buzzer)
Have the vehicle inspected by your Toyota dealer
immediately.
Drive-Start Control
Indicates that the shift position was changed and Drive-
Start Control was operated while depressing the accelera-
tor pedal (with warning buzzer)
Momentarily release the accelerator pedal.
Indicates a malfunction in the Drive-Start Control (with
warning buzzer)
Have the vehicle inspected by your Toyota dealer
immediately.
Parking Support Brake function
Indicates that the Parking Support Brake function (if
equipped) is operating (
Follow the instruction that is displayed on the multi-
information display.
(Canada only)
Low engine oil pressure warning (symbol display)
*
6
Indicates that the engine oil pressure is too low
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer.
Warning light
Warning light/Details/Actions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
597
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
*
1
: Brake system warning buzzer:
When there is a possible problem that could affect braking performance,
the warning light will come on and a warning buzzer will sound.
*
2
: Low engine oil pressure warning buzzer:
A buzzer also sounds continuously for approximately 30 seconds at maxi-
mum in addition to the low engine oil pressure warning light when the
“READY” indicator is illuminated.
*
3
: Open door warning buzzer:
The open door warning buzzer sounds to alert one or more of the doors is
not fully closed (with the vehicle having reached a speed of 3 mph [5 km/h]).
*
4
: Driver’s seat belt warning buzzer:
The driver’s seat belt warning buzzer sounds to alert the driver that his or
her seat belt is not fastened. Once the power switch is turned to ON mode,
the buzzer sounds. If the seat belt is still unfastened, the buzzer sounds
intermittently for a certain period of time after the vehicle reaches a certain
speed.
Front passenger’s seat belt warning buzzer:
The front passenger’s seat belt warning buzzer sounds to alert the front
passenger that his or her seat belt is not fastened. If the seat belt is unfas-
tened, the buzzer sounds intermittently for a certain period of time after the
vehicle reaches a certain speed.
*
5
: Rear passengers’ seat belt warning buzzer:
The rear passengers’ seat belt warning buzzer sounds to alert the rear
passenger that his or her seat belt is not fastened. If the seat belt is unfas-
tened, the buzzer sounds intermittently for a certain period of time, after
the seat belt is fastened and unfastened and the vehicle reaches a certain
speed.
*
6
: This symbol is displayed on the multi-information display.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
598
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
■
SRS warning light
This warning light system monitors the airbag sensor assembly, front impact
sensors, side impact sensors (front door), side impact sensors (front), side
impact sensors (rear), driver’s seat belt buckle switch, front passenger occu-
pant classification system (ECU and sensors), “AIR BAG ON” indicator light,
“AIR BAG OFF” indicator light, front passenger’s seat belt buckle switch, seat
belt pretensioners, airbags, interconnecting wiring and power sources.
(
■
Front passenger detection sensor, seat belt reminder and warning
buzzer
●
If luggage is placed on the front passenger seat, the front passenger detec-
tion sensor may cause the warning light to flash and the warning buzzer to
sound even if a passenger is not sitting in the seat.
●
If a cushion is placed on the seat, the sensor may not detect a passenger,
and the warning light may not operate properly.
■
Electric power steering system warning light (warning buzzer)
When the 12-volt battery charge becomes insufficient or the voltage tempo-
rarily drops, the electric power steering system warning light may come on
and the warning buzzer may sound.
■
If the malfunction indicator lamp comes on while driving
First check the following:
●
Is the fuel tank empty?
If it is, fill the fuel tank immediately.
●
Is the fuel tank cap loose?
If it is, tighten it securely.
The malfunction indicator lamp will go off after several driving trips.
If the malfunction indicator lamp does not go off even after several trips, con-
tact your Toyota dealer as soon as possible.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
599
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
When the tire pressure warning light comes on
Inspect the appearance of the tire to check that the tire is not punctured.
If the tire is punctured:
If the tire is not punctured:
Check the tire inflation pressure and adjust to the appropriate level. Initial-
izing the tire pressure warning system will not turn off the tire pressure
warning light.
■
The tire pressure warning light may come on due to natural causes
The tire pressure warning light may come on due to natural causes such
as natural air leaks and tire inflation pressure changes caused by tem-
perature. In this case, adjusting the tire inflation pressure will turn off the
warning light (after a few minutes).
■
When a tire is replaced with a spare tire
Vehicles with compact spare tire: The compact spare tire is not equipped
with a tire pressure warning valve and transmitter. If a tire goes flat, the
tire pressure warning light will not turn off even though the flat tire has
been replaced with the spare tire. Replace the spare tire with the repaired
tire and adjust the tire inflation pressure. The tire pressure warning light
will go off after a few minutes.
Vehicles with full-size spare tire: The spare tire is also equipped with a tire
pressure warning valve and transmitter. The tire pressure warning light
will turn on if the tire inflation pressure of the spare tire is low. If a tire goes
flat, the tire pressure warning light will not turn off even though the flat tire
has been replaced with the spare tire. Replace the spare tire with the
repaired tire and adjust the tire inflation pressure. The tire pressure warn-
ing light will go off after a few minutes.
■
Conditions that the tire pressure warning system may not function
properly
■
If the tire pressure warning light frequently comes on after blinking
for 1 minute
If the tire pressure warning light frequently comes on after blinking for
1 minute when the power switch is turned to ON mode, have it checked
by your Toyota dealer.
■
Warning buzzer
In some cases, the buzzer may not be heard due to being in a noisy location
or audio sound.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
600
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
WARNING
■
When the electric power steering system warning light comes on
When the light comes on yellow, the assist to the power steering is
restricted. When the light comes on red, the assist to the power steering is
lost and handling operations of the steering wheel become extremely
heavy. When steering wheel operations are heavier than usual, grip the
steering wheel firmly and operate it using more force than usual.
■
If the tire pressure warning light comes on
Be sure to observe the following precautions. Failure to do so could
cause a loss of vehicle control and result in death or serious injury.
●
Stop your vehicle in a safe place as soon as possible. Adjust the tire
inflation pressure immediately.
●
Vehicles with emergency tire puncture repair kit: If the tire pressure
warning light comes on even after tire inflation pressure adjustment, it
is probable that you have a flat tire. Check the tires. If a tire is flat,
repair the flat tire by using emergency tire puncture repair kit.
●
Vehicles with spare tire: If the tire pressure warning light comes on
even after tire inflation pressure adjustment, it is probable that you
have a flat tire. Check the tires. If a tire is flat, change it with the spare
tire and have the flat tire repaired by the nearest Toyota dealer.
●
Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate,
you could lose control of the steering wheel or the brakes.
■
If a blowout or sudden air leakage should occur
The tire pressure warning system may not activate immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
601
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
WARNING
■
Maintenance of the tires
Each tire, including the spare (if provided), should be checked monthly
when cold and inflated to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or tire inflation pressure
label (tire and load information label). (If your vehicle has tires of a dif-
ferent size than the size indicated on the vehicle placard or tire inflation
pressure label [tire and load information label], you should determine
the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped with a tire
pressure monitoring system (TPMS-tire pressure warning system) that
illuminates a low tire pressure telltale (tire pressure warning light) when
one or more of your tires is significantly under-inflated. Accordingly,
when the low tire pressure telltale (tire pressure warning light) illumi-
nates, you should stop and check your tires as soon as possible, and
inflate them to the proper pressure. Driving on a significantly under-
inflated tire causes the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire tread life, and may
affect the vehicle’s handling and stopping ability.
Please note that the TPMS (tire pressure warning system) is not a sub-
stitute for proper tire maintenance, and it is the driver’s responsibility to
maintain correct tire pressure, even if under-inflation has not reached
the level to trigger illumination of the TPMS low tire pressure telltale (tire
pressure warning light).
Your vehicle has also been equipped with a TPMS (tire pressure warn-
ing system) malfunction indicator to indicate when the system is not
operating properly. The TPMS (tire pressure warning system) malfunc-
tion indicator is combined with the low tire pressure telltale (tire pressure
warning light). When the system detects a malfunction, the telltale will
flash for approximately one minute and then remain continuously illumi-
nated. This sequence will continue upon subsequent vehicle start-ups
as long as the malfunction exists. When the malfunction indicator is illu-
minated, the system may not be able to detect or signal low tire pres-
sure as intended.
TPMS (tire pressure warning system) malfunctions may occur for a vari-
ety of reasons, including the installation of replacement or alternate tires
or wheels on the vehicle that prevent the TPMS (tire pressure warning
system) from functioning properly. Always check the TPMS (tire pres-
sure warning system) malfunction telltale after replacing one or more
tires or wheels on your vehicle to ensure that the replacement or alter-
nate tires and wheels allow the TPMS (tire pressure warning system) to
continue to function properly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
602
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
NOTICE
■
To ensure the tire pressure warning system operates properly
Do not install tires with different specifications or makers, as the tire
pressure warning system may not operate properly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
603
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
7-2. Steps to take in an emergency
If a warning message is displayed
Master warning light
The master warning light also
comes on or flashes in order to
indicate that a message is cur-
rently being displayed on the multi-
information display.
*
Multi-information display
Handling method
Follow the instructions of the mes-
sage on the multi-information dis-
play.
If any of the warning messages are shown again after the following
actions have been performed, contact your Toyota dealer.
*
: The master warning light may not come on or flash when a warning mes-
sage is displayed.
The multi-information display shows warnings of system mal-
functions, incorrectly performed operations, and messages that
indicate a need for maintenance. When a message is shown,
perform the correction procedure appropriate to the message.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
604
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
The warning lights and warning buzzers operate as follows depending
on the content of the message. If a message indicates the need for
inspection by a dealer, have the vehicle inspected by your Toyota
dealer immediately.
The operation of the warning lights and warning buzzers may differ
from those stated. In this case, perform the correction procedure
according to the displayed message.
*
: A buzzer sounds the first time a message is shown on the multi-informa-
tion display.
Messages and warnings
System
warning
light
Warning
buzzer
*
Warning
Comes on
Sounds
Indicates an important situation, such
as when a system related to driving is
malfunctioning or that danger may
result if the correction procedure is not
performed
Comes on
or flashes
Sounds
Indicates an important situation, such
as when the systems shown on the
multi-information display may be mal-
functioning
Flashes
Sounds
Indicates a situation, such as when
damage to the vehicle or danger may
result
Comes on
Does not
sound
Indicates a condition, such as mal-
function of electrical components, their
condition, or indicates the need for
maintenance
Flashes
Does not
sound
Indicates a situation, such as when an
operation has been performed incor-
rectly, or indicates how to perform an
operation correctly
-------------------------------------------------------------------------------------------------------------------------------------------------------------
605
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
Warning messages
The warning messages explained below may differ from the actual messages
according to operation conditions and vehicle specifications.
■
System warning lights
The master warning light does not come on or flash in the following cases.
Instead, a separate system warning light will come on along with a message
or image shown on the multi-information display.
●
“Antilock Brake System Malfunction Visit Your Dealer”:
The ABS warning light comes on. (
●
“Braking Power Low Visit Your Dealer”:
The brake system warning light (yellow) will come on. (
●
Indicates that a door is not fully closed while the vehicle is stopped.:
The Open door warning light comes on. (
■
If “Visit Your Dealer” is shown
The system or part shown on the multi-information display is malfunctioning.
Have the vehicle inspected by your Toyota dealer.
■
If a message about an operation is shown
●
If a message about an operation of the accelerator pedal or brake pedal is
shown
• A warning message about an operation of the brake pedal may be shown
while the driving assist systems such as PCS (Pre-Collision System) (if
equipped) or the dynamic radar cruise control with full-speed range (if
equipped) is operating. If a warning message is shown, be sure to decel-
erate the vehicle or follow an instruction shown on the multi-information
display.
• A warning message is shown when Brake Override System operates.
(
• A warning message is shown when Drive-Start Control or Parking Sup-
port Brake function (if equipped) operates (
instructions on the multi-information display.
●
If a message about an operation of the power switch is shown
An instruction for operation of the power switch is shown when the incorrect
procedure for starting the hybrid system is performed or the power switch is
operated incorrectly. Follow the instructions shown on the multi-information
display to operate the power switch again.
●
If a message about a shift operation is shown
To prevent the shift position from being selected incorrectly or the vehicle
from moving unexpectedly, the shift position may be changed automatically
(
P. 257) or shift operation may be required. In this case, change the shift
position following the instructions on the multi-information display.
●
If a message or image about an open/close state of a part or replenishment
of a consumable is shown
Confirm the part indicated by the multi-information display or a warning light,
and then perform the coping method such as closing the open door or
replenishing a consumable.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
606
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
■
If “See Owner’s Manual” is shown
●
If “Braking Power Low Stop in a Safe Place See Owner’s Manual” is shown,
this may be a malfunction. Immediately stop the vehicle in a safe place and
contact your Toyota dealer. Continuing to drive the vehicle may be danger-
ous.
●
If “Engine Oil Pressure Low” is shown, this may be a malfunction. Immedi-
ately stop the vehicle in a safe place and contact your Toyota dealer.
●
If the following messages are shown, there may be a malfunction. Immedi-
ately have the vehicle inspected by your Toyota dealer.
• “Hybrid System Malfunction”
• “Check Engine”
• “Hybrid Battery System Malfunction”
• “Accelerator System Malfunction”
• “Smart Key System Malfunction See Owner’s Manual”
■
If “Shift System Not Active Apply Parking Brake Securely While Parking
See Owner’s Manual” is shown
Indicates a temporary operation failure or malfunction in the shift control sys-
tem. Immediately have the vehicle inspected by your Toyota dealer.
When the message is shown, the hybrid system may not be started or the
shift position may not be changed normally. (Coping method:
■
If “Shift System Malfunction Apply Parking Brake Securely While Park-
ing See Owner’s Manual” is shown
Indicates a malfunction in the shift control system. Immediately have the vehi-
cle inspected by your Toyota dealer.
When the message is shown, the hybrid system may not be started or the
shift position may not be changed normally. (Coping method:
■
If “
Switch Malfunction Apply Parking Brake Securely While Parking
See Owner’s Manual” is shown
The P position switch may not operate. Immediately have the vehicle
inspected by your Toyota dealer.
When parking the vehicle, stop the vehicle on level ground and apply the
parking brake firmly.
■
If “Shift System Malfunction Shifting Unavailable See Owner’s Manual”
is shown
Indicates a malfunction in the shift control system. Immediately have the vehi-
cle inspected by your Toyota dealer.
The shift position may not be shifted from P to other than P.
■
If “Shift System Malfunction Stop in a Safe Place See Owner’s Manual”
is shown
Indicates a malfunction in the shift control system. Immediately have the vehi-
cle inspected by your Toyota dealer.
The shift position may not be changed. Stop the vehicle in a safe place.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
607
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
If “Shift System Malfunction See Owner’s Manual” is shown
Indicates a malfunction in the shift control system. Immediately have the sys-
tem inspected by your Toyota dealer.
The system may not operate properly.
■
If “Low 12-Volt Battery Apply Parking Brake Securely While Parking See
Owner’s Manual” is shown
Indicates that the 12-volt battery charge is insufficient. Charge or replace the
12-volt battery.
●
When the message is shown, the hybrid system may not start or the shift
position may not be changed normally. (Coping method:
●
After charging the 12-volt battery, the message may not go off until the shift
position is changed from P.
■
If “Shifting Unavailable Low 12-Volt Battery See Owner’s Manual” is
shown
Indicates that the shift position cannot be changed because the voltage of the
12-volt battery drops. Charge or replace the 12-volt battery.
(Coping method in the case the 12-volt battery is discharged:
■
If “Hybrid System Overheated. Reduced Output Power.” is shown
The message may be shown when driving under severe operating conditions.
(For example, when driving up a long steep hill or driving up a steep hill in
reverse.)
Coping method:
■
If “Maintenance required for Traction battery cooling parts See owner’s
manual” is shown
The filter may be clogged, the air intake vent may be blocked or there may be
a gap in the duct.
●
If the air intake vent is dirty, refer to P. 551 for information on how to clean
the air intake vent.
●
If the message is shown when the air intake vent is not dirty, have the vehi-
cle inspected by your Toyota dealer.
■
If “Traction Battery Needs to be Protected Refrain From the Use of
Position” is shown
This message may be displayed when the shift position is in N.
As the hybrid battery (traction battery) can not be charged when the shift
position is in N, shift the shift position to P when the vehicle is stopped.
■
If “Traction Battery Needs to be Protected Shift into
to Restart” is
shown
This message is displayed when the hybrid battery (traction battery) charge
has become extremely low because the vehicle has been left with the N shift
position selected for a certain amount of time.
When operating the vehicle, shift to P and restart the hybrid system.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
608
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
■
If “Shift to
Before Exiting Vehicle” is shown
Message is displayed when the driver’s door is opened without turning the
power switch to off with the shift position in any position other than P.
Shift the shift position to P.
■
If “Shift is in
Release Accelerator Before Shifting” is shown
Message is displayed when the accelerator pedal has been depressed and
the shift position is in N.
Release the accelerator pedal and shift the shift position to D or R.
■
If “Depress Brake When Vehicle is Stopped. Hybrid System may Over-
heat.” is shown
The message may be shown when the accelerator pedal is depressed to hold
the vehicle while the vehicle is stopped on an uphill, etc.
The hybrid system may overheat. Release the accelerator pedal and depress
the brake pedal.
■
If “Shifted to
Stop Vehicle to Shift to
” is shown
If the P position switch is pressed while driving, the shift position is changed
to N and the message is shown. (
■
If “Auto Power OFF to Conserve Battery” is shown
The power switch has been turned off by the automatic power off function.
When starting the hybrid system next time, operate the hybrid system for
approximately 5 minutes to recharge the 12-volt battery.
■
If “Engine Oil Level Low Add or Replace” is displayed
The engine oil level may be low. Check the level of the engine oil, and add
engine oil if necessary. This message may be displayed if the vehicle is
stopped on a slope. Move the vehicle to a level surface and check if the mes-
sage disappears.
■
If “Accelerator and Brake Pedals Pressed Simultaneously” is shown
The accelerator and brake pedals are being depressed simultaneously.
(
Release the accelerator pedal and depress the brake pedal.
■
If a message that indicates the malfunction of front camera is dis-
played.
*
The following systems may be suspended until the problem shown in the
message is resolved. (
●
PCS (Pre-Collision System)
*
●
LTA (Lane Tracing Assist)
*
●
AHB (Automatic High Beam)
*
●
RSA (Road Sign Assist)
*
●
Dynamic radar cruise control with full-speed range
*
*
: If equipped
-------------------------------------------------------------------------------------------------------------------------------------------------------------
609
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
If “Radar Cruise Control Unavailable See Owner’s Manual” is shown
The dynamic radar cruise control with full-speed range system is suspended
temporarily or until the problem shown in the message is resolved. (causes
and coping methods:
■
If “Radar Cruise Control Unavailable” is shown
The dynamic radar cruise control with full-speed range system cannot be
used temporarily. Use the system when it becomes available again.
■
If “Maintenance Required Soon” is displayed (U.S.A. only)
Indicates that all maintenance according to the driven distance on the mainte-
nance schedule
*
should be performed soon.
Comes on approximately 4500 miles (7200 km) after the message has been
reset.
If necessary, perform maintenance. Please reset the message after the main-
tenance is performed. (
*
: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
■
If “Maintenance Required Visit Your Dealer” is displayed (U.S.A. only)
Indicates that all maintenance is required to correspond to the driven distance
on the maintenance schedule
*
.
Comes on approximately 5000 miles (8000 km) after the message has been
reset. (The indicator will not work properly unless the message has been
reset.)
Perform the necessary maintenance. Please reset the message after the
maintenance is performed. (
*
: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
■
If the shift position cannot be changed or the power switch is turned to
ACCESSORY mode even if trying to turn the power switch off when a
warning message is shown
If the 12-volt battery is discharged or the shift control system is malfunction-
ing, the followings may occur.
●
The shift position may not be changed to P.
When parking, stop the vehicle on level ground and apply the parking brake
firmly.
●
The hybrid system may not start.
●
The power switch may be turned to ACCESSORY mode even if trying to
turn the power switch off.
In this case, the power switch may be turned off after applying the parking
brake.
●
The automatic P position selection function (
Before turning the power switch off, be sure to press the P position switch
and check that the shift position is in P by the shift position indicator or P
position switch indicator.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
610
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
■
Warning buzzer
NOTICE
■
If “Have Traction Battery Inspected” is shown
The hybrid battery (traction battery) is scheduled to be inspected or
replaced. Have the vehicle inspected by your Toyota dealer immediately.
●
Continuing to drive the vehicle without having the hybrid battery (traction
battery) inspected will cause the hybrid system not to start.
●
If the hybrid system does not start, contact your Toyota dealer immedi-
ately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
611
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
7-2. Steps to take in an emergency
If you have a flat tire (vehicles without
spare tire)
Your vehicle is not equipped with a spare tire, but instead is
equipped with an emergency tire puncture repair kit.
A puncture caused by a nail or screw passing through the tire
tread can be repaired temporarily using the emergency tire
puncture repair kit. (The kit contains a bottle of sealant. The
sealant can be used only once to temporarily repair one tire
without removing the nail or screw from the tire.) After temporar-
ily repairing the tire with the kit, have the tire repaired or
replaced by your Toyota dealer.
WARNING
■
If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair, which could result in an accident.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
612
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
●
Stop the vehicle in a safe place on a hard, flat surface.
●
Set the parking brake.
●
Shift the shift position to P.
●
Stop the hybrid system.
●
Turn on the emergency flashers.
●
Check the degree of the tire damage.
A tire should only be repaired
with the emergency tire punc-
ture repair kit if the damage is
caused by a nail or screw pass-
ing through the tire tread.
• Do not remove the nail or
screw from the tire. Remov-
ing the object may widen the
opening and make emer-
gency repair with the repair
kit impossible.
• To avoid sealant leakage, move the vehicle until the area of the
puncture, if known, is positioned at the top of the tire.
■
A flat tire that cannot be repaired with the emergency tire puncture
repair kit
In the following cases, the tire cannot be repaired with the emergency tire
puncture repair kit. Contact your Toyota dealer.
●
When the tire is damaged due to driving without sufficient air pressure
●
When there are any cracks or damage at any location on the tire, such
as on the side wall, except the tread
●
When the tire is visibly separated from the wheel
●
When the cut or damage to the tread is 0.16 in. (4 mm) long or more
●
When the wheel is damaged
●
When two or more tires have been punctured
●
When more than one sharp objects such as nails or screws have passed
through the tread on a single tire
●
When the sealant has expired
Before repairing the tire
-------------------------------------------------------------------------------------------------------------------------------------------------------------
613
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
2WD models
Location of the emergency tire puncture repair kit and tools
Jack handle
Jack
(Use of the jack:
Wheel nut wrench
Emergency tire puncture
repair kit
Towing eyelet
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
614
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
AWD models
Towing eyelet
Jack handle
Wheel nut wrench
Emergency tire puncture
repair kit
Jack
(Use of the jack:
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
615
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Emergency tire puncture repair kit components
Hose
Air release cap
Sticker
Power plug
Air pressure gauge
Compressor switch
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
616
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Pull up the handle to open the
deck board.
Secure the deck board using
the grocery bag hooks.
(
Take out the emergency tire puncture repair kit.
2WD models: If the luggage cover (if equipped) is stowed, turn over the
tonneau cover to take out the emergency tire puncture repair kit.
Taking out the emergency tire puncture repair kit
1
2
3
2WD models
AWD models
-------------------------------------------------------------------------------------------------------------------------------------------------------------
617
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
Taking out the jack
Unhook the tightening strap and take out the jack.
■
Storing the jack
Place the jack in the same direction as the mark next to the storage
space.
2WD models
AWD models
2WD models
AWD models
WARNING
■
After using the tools and jack
Before driving, make sure all the tools and jack are securely in place in
their storage location to reduce the possibility of personal injury during a
collision or sudden braking.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
618
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Take out the repair kit from the plastic bag.
Remove the valve cap from the
valve of the punctured tire.
Extend the hose. Remove the
air release cap from the hose.
Attach the sticker enclosed with
the bottle on the specified loca-
tions. (See step
.)
You will use the air release cap
again. Therefore keep it in a safe
place.
Connect the hose to the valve.
Screw the end of the hose clock-
wise as far as possible.
Emergency repair method
1
2
3
10
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
619
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Make sure that the compressor
switch is off.
Lift the rubber stopper on the
compressor.
Remove the power plug from
the compressor.
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
620
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Connect the power plug to the
power outlet socket. (
Connect the bottle to the com-
pressor.
As shown in the illustration, insert
the bottle securely into the com-
pressor until the upper side of the
mark on the bottle is aligned with
the upper end of the notch.
Attach the sticker provided with
the tire puncture repair kit to a
position easily seen from the
driver’s seat.
8
9
10
-------------------------------------------------------------------------------------------------------------------------------------------------------------
621
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Check the specified tire inflation
pressure.
Tire inflation pressure is specified
on the label on the driver’s side
pillar as shown. (
Start the hybrid system. (
To inject the sealant and inflate
the tire, turn the compressor
switch on.
11
12
13
-------------------------------------------------------------------------------------------------------------------------------------------------------------
622
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Inflate the tire until the specified air pressure is reached.
The sealant will be injected
and the pressure will spike to
between 44 psi (300 kPa,
3.0 kgf/cm
2
or bar) and
58 psi (400 kPa, 4.0 kgf/cm
2
or bar), then gradually
decrease.
The air pressure gauge will
display the actual tire infla-
tion pressure about 1 to 5
minutes after the switch is
turned on.
• Turn the compressor switch
off and then check the tire
inflation
pressure.
Being
careful not to over inflate,
check and repeat the inflation
procedure until the specified
tire inflation pressure is
reached.
• The tire can be inflated for about 5 to 20 minutes (depending on
the outside temperature). If the tire inflation pressure is still lower
than the specified point after inflation for 25 minutes, the tire is
too damaged to be repaired. Turn the compressor switch off and
contact your Toyota dealer.
• If the tire inflation pressure exceeds the specified air pressure, let
out some air to adjust the tire inflation pressure. (
With the compressor switch off, disconnect the hose from the valve
on the tire and then pull out the power plug from the power outlet
socket.
Some sealant may leak when the hose is removed.
Install the valve cap onto the valve of the emergency repaired tire.
14
1
2
15
16
-------------------------------------------------------------------------------------------------------------------------------------------------------------
623
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Attach the air release cap to the
end of the hose.
If the air release cap is not
attached, the sealant may leak
and the vehicle may get dirty.
Temporarily store the bottle in the luggage compartment while it is
connected to the compressor.
To spread the liquid sealant evenly within the tire, immediately drive
safely for about 3 miles (5 km) below 50 mph (80 km/h).
After driving, stop your vehicle
in a safe place on a hard, flat
surface and reconnect the
repair kit.
Remove the air release cap from
the hose before reconnecting the
hose.
Turn the compressor switch on and wait for several seconds, then
turn it off. Check the tire inflation pressure.
If the tire inflation pressure is
under
19 psi
(130 kPa,
1.3 kgf/cm
2
or bar): The
puncture cannot be repaired.
Contact your Toyota dealer.
If the tire inflation pressure is
19 psi (130 kPa, 1.3 kgf/cm
2
or bar) or higher, but less
than the specified air pres-
sure: Proceed to step
.
If the tire inflation pressure is the specified air pressure (
Proceed to step
.
17
18
19
20
21
1
2
22
3
23
-------------------------------------------------------------------------------------------------------------------------------------------------------------
624
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Turn the compressor switch on to inflate the tire until the specified
air pressure is reached. Drive for about 3 miles (5 km) and then
perform step
.
Attach the air release cap to the
end of the hose.
If the air release cap is not
attached, the sealant may leak
and the vehicle may get dirty.
Store the bottle in the luggage compartment while it is connected to
the compressor.
Taking precautions to avoid sudden braking, sudden acceleration
and sharp turns, drive carefully at under 50 mph (80 km/h) to the
nearest Toyota dealer that is less than 62 miles (100 km) away for
tire repair or replacement.
When having the tire repaired or replaced, make sure to tell the Toyota
dealer that the sealant is injected.
22
20
23
24
25
-------------------------------------------------------------------------------------------------------------------------------------------------------------
625
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
If the tire is inflated to more than the specified air pressure
Disconnect the hose from the valve.
Disconnect the hose from the valve, remove the air release cap from
the hose and then reconnect the hose.
Turn the compressor switch on and wait for several seconds, and then
turn it off. Check that the air pressure indicator shows the specified air
pressure. (
If the air pressure is under the designated pressure, turn the compres-
sor switch on again and repeat the inflation procedure until the speci-
fied air pressure is reached.
■
The valve of a tire that has been repaired
After a tire is repaired with the emergency tire puncture repair kit, the
valve should be replaced.
■
After a tire is repaired with the emergency tire puncture repair kit
●
The tire pressure warning valve and transmitter should be replaced.
●
Even if the tire inflation pressure is at the recommended level, the tire
pressure warning light may come on/flash.
■
Note for checking the emergency tire puncture repair kit
Check the sealant expiry date occasionally.
The expiry date is shown on the bottle. Do not use sealant whose expiry
date has already passed. Otherwise, repairs conducted using the emer-
gency tire puncture repair kit may not be performed properly.
Install the air release cap to the end of
the hose and push the protrusion on
the air release cap into the tire valve
to let some air out.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
626
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
■
Emergency tire puncture repair kit
●
The emergency tire puncture repair kit is for filling the car tire with air.
●
The sealant has a limited life span. The expiry date is marked on the
bottle. The sealant should be replaced before the expiry date. Contact
your Toyota dealer for replacement.
●
The sealant stored in the emergency tire puncture repair kit can be used
only once to temporarily repair a single tire. If the sealant in the bottle
and other parts of the kit have been used and need to be replaced, con-
tact your Toyota dealer.
●
The compressor can be used repeatedly.
●
The sealant can be used when the outside temperature is from -40°F
(-40°C) to 140°F (60°C).
●
The kit is exclusively designed for size and type of tires originally
installed on your vehicle. Do not use it for tires that a different size than
the original ones, or for any other purposes.
●
If the sealant gets on your clothes, it may stain.
●
If the sealant adheres to a wheel or the surface of the vehicle body, the
stain may not be removable if it is not cleaned at once. Immediately wipe
away the sealant with a wet cloth.
●
During operation of the repair kit, a loud operation noise is produced.
This does not indicate a malfunction.
●
Do not use to check or to adjust the tire pressure.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
627
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
WARNING
■
Do not drive the vehicle with a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair.
Driving with a flat tire may cause a circumferential groove on the side
wall. In such a case, the tire may explode when using a repair kit.
■
Caution while driving
●
Store the repair kit in the luggage compartment.
Injuries may result in the event of an accident or sudden braking.
●
The repair kit is exclusively only for your vehicle.
Do not use repair kit on other vehicles, which could lead to an accident
causing death or serious injury.
●
Do not use repair kit for tires that are different size than the original
ones, or for any other purpose. If the tires have not been completely
repaired, it could lead to an accident causing death or serious injury.
■
Precautions for use of the sealant
●
Ingesting the sealant is hazardous to your health. If you ingest sealant,
consume as much water as possible, and then immediately consult a
doctor.
●
If sealant gets in eyes or adheres to skin, immediately wash it off with
water. If discomfort persists, consult a doctor.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
628
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
WARNING
■
When fixing the flat tire
●
Stop your vehicle in a safe and flat area.
●
Do not touch the wheels or the area around the brakes immediately
after the vehicle has been driven.
After the vehicle has been driven, the wheels and the area around the
brakes may be extremely hot. Touching these areas with hands, feet or
other body parts may result in burns.
●
Connect the valve and hose securely with the tire installed on the vehi-
cle. If the hose is not properly connected to the valve, air leakage may
occur as sealant may be sprayed out.
●
If the hose comes off the valve while inflating the tire, there is a risk
that the hose will move abruptly due to air pressure.
●
After inflation of the tire has completed, the sealant may splatter when
the hose is disconnected or some air is let out of the tire.
●
Follow the operation procedure to repair the tire. If the procedures not
followed, the sealant may spray out.
●
Keep back from the tire while it is being repaired, as there is a chance
of it bursting while the repair operation is being performed. If you
notice any cracks or deformation of the tire, turn off the compressor
switch and stop the repair operation immediately.
●
The repair kit may overheat if operated for a long period of time. Do not
operate the repair kit continuously for more than 40 minutes.
●
Parts of the repair kit become hot during operation. Be careful handling
the repair kit during and after operation. Do not touch the metal part
connecting the bottle and the compressor. It will be extremely hot.
●
Do not attach the vehicle speed warning sticker to an area other than
the one indicated. If the sticker is attached to an area where an SRS
airbag is located, such as the pad of the steering wheel, it may prevent
the SRS airbag from operating properly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
629
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
WARNING
■
Driving to spread the liquid sealant evenly
Observe the following precautions to reduce the risk of accidents.
Failing to do so may result in a loss of vehicle control and cause death
or serious injury.
●
Drive the vehicle carefully at a low speed. Be especially careful when
turning and cornering.
●
If the vehicle does not drive straight or you feel a pull through the
steering wheel, stop the vehicle and check the following.
• Tire condition. The tire may have separated from the wheel.
• Tire inflation pressure. If the tire inflation pressure is 19 psi
(130 kPa, 1.3 kgf/cm
2
or bar) or less, the tire may be severely dam-
aged.
NOTICE
■
When performing an emergency repair
●
A tire should only be repaired with the emergency tire puncture repair
kit if the damage is caused by a sharp object such as nail or screw
passing through the tire tread.
Do not remove the sharp object from the tire. Removing the object may
widen the opening and disenable emergency repair with the repair kit.
●
The repair kit is not waterproof. Make sure that the repair kit is not
exposed to water, such as when it is being used in the rain.
●
Do not put the repair kit directly onto dusty ground such as sand at the
side of the road. If the repair kit vacuums up dust etc., a malfunction
may occur.
■
Precautions for the emergency tire puncture repair kit
●
The repair kit power source should be 12 V DC suitable for vehicle
use. Do not connect the repair kit to any other source.
●
If fuel splatters on the repair kit, the repair kit may deteriorate. Take
care not to allow fuel to contact it.
●
Place the repair kit in a storage to prevent it from being exposed to dirt
or water.
●
Store the repair kit in the luggage compartment out of reach of chil-
dren.
●
Do not disassemble or modify the repair kit. Do not subject parts such
as the air pressure indicator to impacts. This may cause a malfunction.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
630
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
NOTICE
■
To avoid damage to the tire pressure warning valves and transmit-
ters
When a tire is repaired with liquid sealants, the tire pressure warning
valve and transmitter may not operate properly. If a liquid sealant is
used, contact your Toyota dealer or other qualified service shop as soon
as possible. After use of liquid sealant, make sure to replace the tire
pressure warning valve and transmitter when repairing or replacing the
tire. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
631
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
7-2. Steps to take in an emergency
If you have a flat tire (vehicles with spare
tire)
●
Stop the vehicle in a safe place on a hard, flat surface.
●
Set the parking brake.
●
Shift the shift position to P.
●
Stop the hybrid system.
●
Turn on the emergency flashers. (
Your vehicle is equipped with a spare tire. The flat tire can be
replaced with the spare tire.
For details about tires:
WARNING
■
If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair, which could result in an accident.
Before jacking up the vehicle
-------------------------------------------------------------------------------------------------------------------------------------------------------------
632
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Vehicles with compact spare tire
Location of the spare tire, jack and tools
Wheel nut wrench
Jack handle
Towing eyelet
Jack
Spare tire
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
633
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Vehicles with full-size spare tire
Jack handle
Wheel nut wrench
Spare tire
Towing eyelet
Jack
1
2
3
4
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
634
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
WARNING
■
Using the tire jack
Observe the following precautions.
Improper use of the tire jack may cause the vehicle to suddenly fall off
the jack, leading to death or serious injury.
●
Only use the tire jack that comes with this vehicle for replacing a flat
tire.
Do not use it on other vehicles, and do not use other tire jacks for
replacing tires on this vehicle.
●
Do not raise the vehicle while someone is inside.
●
Do not use the tire jack for any purpose other than replacing tires or
installing and removing tire chains.
●
Do not put any part of your body under the vehicle while it is supported
by the jack.
●
Do not start the hybrid system or drive the vehicle while the vehicle is
supported by the jack.
●
When raising the vehicle, do not put an object on or under the jack.
●
Do not raise the vehicle to a height greater than that required to
replace the tire.
●
Use a jack stand if it is necessary to get under the vehicle.
●
When lowering the vehicle, make sure that there is no-one near the
vehicle. If there are people nearby, warn them vocally before lowering.
●
Put the jack properly in its jack point.
(
-------------------------------------------------------------------------------------------------------------------------------------------------------------
635
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Pull up the handle to open the
deck board.
Secure the deck board using
the grocery bag hooks.
(
Unhook the tightening strap
and take out the jack.
Taking out the jack
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
636
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Open and secure the deck board. (
Remove the tray.
Vehicles with compact spare tire: If the luggage cover is stowed
(
P. 472), remove both the tray and luggage cover.
Loosen the center fastener that
secures the spare tire.
Taking out the spare tire
1
2
Vehicles with compact spare
tire
Vehicles with full-size spare
tire
3
WARNING
■
When storing the spare tire
Be careful not to catch fingers or other body parts between the spare
tire and the body of the vehicle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
637
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Chock the tires.
For vehicles with the wheel
ornament: Remove the wheel
ornament using the wrench.
To prevent damage, cover the
tip of the wrench with a rag.
Slightly loosen the wheel nuts
(one turn).
Replacing a flat tire
1
Flat tire
Wheel chock positions
Front
Left-hand side
Behind the rear right-hand side tire
Right-hand side
Behind the rear left-hand side tire
Rear
Left-hand side
In front of the front right-hand side tire
Right-hand side
In front of the front left-hand side tire
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
638
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Turn the tire jack portion
by
hand until the center of the
recessed portion of the jack is
in contact with the center of the
jack point.
Assemble the jack handle and
the wheel nut wrench as shown
in the illustration.
Raise the vehicle until the tire is
slightly raised off the ground.
Remove all the wheel nuts and
the tire.
When resting the tire on the
ground, place the tire so that the
wheel design faces up to avoid
scratching the wheel surface.
Jack point
4
A
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
639
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
WARNING
■
Replacing a flat tire
●
Do not touch the disc wheels or the area around the brakes immedi-
ately after the vehicle has been driven.
After the vehicle has been driven the disc wheels and the area around
the brakes will be extremely hot. Touching these areas with hands, feet
or other body parts while changing a tire, etc. may result in burns.
●
Failure to follow these precautions could cause the wheel nuts to
loosen and the tire to fall off, resulting in death or serious injury.
• Have the wheel nuts tightened with a torque wrench to 76 ft•lbf
(103 N•m, 10.5 kgf•m) as soon as possible after changing wheels.
• When installing a tire, only use wheel nuts that have been specifi-
cally designed for that wheel.
• If there are any cracks or deformations in the bolt screws, nut
threads or bolt holes of the wheel, have the vehicle inspected by
your Toyota dealer.
• When installing the wheel nuts, be sure to install the wheel nuts with
the tapered ends facing inward.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
640
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Remove any dirt or foreign mat-
ter from the wheel contact sur-
face.
If foreign matter is on the wheel
contact surface, the wheel nuts
may loosen while the vehicle is in
motion, causing the tire to come
off.
Install the spare tire and loosely tighten each wheel nut by hand by
approximately the same amount.
When replacing an aluminum
wheel with a steel wheel
(including a compact spare
tire), tighten the wheel nuts until
the tapered portion comes into
loose contact with the disc
wheel seat.
When replacing an aluminum
wheel with an aluminum wheel,
turn the wheel nuts until the
washers come into contact with
the disc wheel.
Installing the spare tire
1
2
Tapered portion
Disc wheel seat
Washer
Disc wheel
-------------------------------------------------------------------------------------------------------------------------------------------------------------
641
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Lower the vehicle.
Firmly tighten each wheel nut
two or three times in the order
shown in the illustration.
Tightening torque:
76 ft•lbf (103 N•m, 10.5 kgf•m)
For vehicles with the wheel
ornament: When reinstalling an
original wheel or installing a full-
size spare tire, reinstall the
wheel ornament.
*
Align the cutout of the wheel
ornament with the valve stem as
shown.
*
: The wheel ornament cannot be
installed on the compact spare
tire.
Stow the flat tire, tire jack and all tools.
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
642
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
■
The compact spare tire (if equipped)
●
The compact spare tire is identified by the label “TEMPORARY USE
ONLY” on the tire sidewall.
Use the compact spare tire temporarily, and only in an emergency.
●
Make sure to check the tire inflation pressure of the compact spare tire.
(
■
When using the compact spare tire (if equipped)
As the compact spare tire is not equipped with a tire pressure warning
valve and transmitter, low inflation pressure of the spare tire will not be
indicated by the tire pressure warning system. Also, if you replace the
compact spare tire after the tire pressure warning light comes on, the light
remains on.
■
When the compact spare tire is equipped (if equipped)
The vehicle height may become lower when driving with the compact
spare tire compared to when driving with standard tires.
■
If you have a flat front tire on a road covered with snow or ice (vehi-
cles with compact spare tire)
Install the compact spare tire on one of the rear wheels of the vehicle.
Perform the following steps and fit tire chains to the front tires:
Replace a rear tire with the compact spare tire.
Replace the flat front tire with the tire removed from the rear of the vehi-
cle.
Fit tire chains to the front tires.
■
Jack point
■
Storing the jack
The mark indicating the jack point is
stamped on the underside of the vehi-
cle.
Place the jack in the same direction as
the mark next to the storage space.
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
643
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
WARNING
■
When using the compact spare tire (if equipped)
●
Remember that the spare tire provided is specifically designed for use
with your vehicle. Do not use your spare tire on another vehicle.
●
Do not use more than one compact spare tire simultaneously.
●
Replace the spare tire with a standard tire as soon as possible.
●
Avoid sudden acceleration, abrupt steering, sudden braking and shift-
ing operations that cause sudden engine braking.
■
When the compact spare tire is attached (if equipped)
The vehicle speed may not be correctly detected, and the following sys-
tems may not operate correctly:
Also, not only can the following system not be utilized fully, but it may
even negatively affect the drive-train components:
• E-Four (Electric Four wheel drive system)
*
*
: If equipped
■
Speed limit when using the compact spare tire (if equipped)
Do not drive at speeds in excess of 50 mph (80 km/h) when a compact
spare tire is installed on the vehicle.
The compact spare tire is not designed for driving at high speeds. Fail-
ure to observe this precaution may lead to an accident causing death or
serious injury.
■
After using the tools and jack
Before driving, make sure all the tools and jack are securely in place in
their storage location to reduce the possibility of personal injury during a
collision or sudden braking.
• ABS & Brake assist
• VSC
• TRAC
• EPS
• AHB (Automatic High Beam)
*
• PCS (Pre-Collision System)
*
• LTA (Lane Tracing Assist)
*
• Dynamic radar cruise control
with full-speed range
*
• Cruise control
*
• BSM (Blind Spot Monitor)
*
• Intuitive parking assist
*
• Parking Support Brake function
*
• S-APGS (Simple Advanced
Parking Guidance System)
*
• Rear view monitor system
• Navigation system
*
-------------------------------------------------------------------------------------------------------------------------------------------------------------
644
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
NOTICE
■
Be careful when driving over bumps with the compact spare tire
installed on the vehicle. (if equipped)
The vehicle height may become lower when driving with the compact
spare tire, compared to when driving with standard tires. Be careful
when driving over uneven road surfaces.
■
Driving with tire chains and the compact spare tire (if equipped)
Do not fit tire chains to the compact spare tire.
Tire chains may damage the vehicle body and adversely affect driving
performance.
■
When replacing the tires
When removing or fitting the wheels, tires or the tire pressure warning
valve and transmitter, contact your Toyota dealer as the tire pressure
warning valve and transmitter may be damaged if not handled correctly.
■
Handling the decorative resin parts (for vehicles equipped with 17-
inch wheels)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
645
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
7-2. Steps to take in an emergency
If the hybrid system will not start
One of the following may be the cause of the problem:
●
The electronic key may not be functioning properly.
*
(
●
There may not be sufficient fuel in the vehicle’s tank.
Refuel the vehicle. (
●
There may be a malfunction in the immobilizer system.
*
(
●
There may be a malfunction in the shift control system.
*
(
●
The hybrid system may be malfunctioning due to an electrical prob-
lem such as electronic key battery depletion or a blown fuse. How-
ever, depending on the type of malfunction, an interim measure is
available to start the hybrid system. (
●
There is a possibility that the temperature of the hybrid battery
(traction battery) is extremely low (approximately below -22°F
[-30°C]). (
*
: It may not be possible to shift the shift position other than P.
One of the following may be the cause of the problem:
●
The 12-volt battery may be discharged. (
●
The 12-volt battery terminal connections may be loose or corroded.
(
Reasons for the hybrid system not starting vary depending on
the situation. Check the following and perform the appropriate
procedure:
The hybrid system will not start even though the correct starting
procedure is being followed. (
The interior lights and headlights are dim, or the horn does not
sound or sounds at a low volume.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
646
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
One of the following may be the cause of the problem:
●
The 12-volt battery may be discharged. (
●
One or both of the 12-volt battery terminals may be disconnected.
(
Contact your Toyota dealer if the problem cannot be repaired, or if repair
procedures are unknown.
When the hybrid system does not start, the following steps can be
used as an interim measure to start the hybrid system if the power
switch is functioning normally.
Do not use this starting procedure except in cases of emergency.
Set the parking brake.
Turn the power switch to ACCESSORY mode.
Press and hold the power switch for about 15 seconds while
depressing the brake pedal firmly.
Even if the hybrid system can be started using the above steps, the
system may be malfunctioning. Have the vehicle inspected by your
Toyota dealer.
The interior lights and headlights do not turn on, or the horn
does not sound.
Emergency start function
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
647
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
7-2. Steps to take in an emergency
If the electronic key does not operate
properly
Use the mechanical key (
P. 181) in order to perform the following
operations:
Locks all the doors
Closes the windows and moon
roof
*
1
(turn and hold)
*
2
Unlocks the door
Turning the key rearward unlocks
the driver’s door. Turning the key
once again within 3 seconds
unlocks the other doors.
Opens the windows and moon roof
*
1
(turn and hold)
*
2
*
1
: If equipped
*
2
: This setting must be customized at your Toyota dealer. (
If communication between the electronic key and vehicle is
interrupted (
P. 198) or the electronic key cannot be used
because the battery is depleted, the smart key system and
wireless remote control cannot be used. In such cases, the
doors can be opened and the hybrid system can be started by
following the procedure below.
Locking and unlocking the doors
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
648
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Depress the brake pedal.
Touch the Toyota emblem side
of the electronic key to the
power switch.
When the electronic key is
detected, a buzzer sounds and the
power switch will turn to ON mode.
When the smart key system is
deactivated in customization set-
ting, the power switch will turn to
ACCESSORY mode.
Firmly depress the brake pedal
and check that
is shown
on the multi-information display.
Press the power switch.
In the event that the hybrid system still cannot be operated, contact
your Toyota dealer.
Starting the hybrid system
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
649
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
Stopping the hybrid system
Set the parking brake, shift the shift position to P and press the power switch
as you normally do when stopping the hybrid system.
■
Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the
electronic key battery be replaced immediately when the battery is depleted.
(
■
Changing power switch modes
Release the brake pedal and press the power switch in step
above. The
hybrid system does not start and modes will be changed each time the switch
is pressed. (
■
When the electronic key does not work properly
●
Make sure that the smart key system has not been deactivated in the cus-
tomization setting. If it is off, turn the function on.
(Customizable features:
●
Check if battery-saving mode is set. If it is set, cancel the function.
(
WARNING
■
When using the mechanical key and operating the power windows or
moon roof (if equipped)
Operate the power window or moon roof after checking to make sure that
there is no possibility of any passenger having any of their body parts
caught in the window or moon roof.
Also, do not allow children to operate the mechanical key. It is possible for
children and other passengers to get caught in the power window or moon
roof.
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
650
PRIUS_OM_OM47E09U_(U)
7-2. Steps to take in an emergency
If the 12-volt battery is discharged
If you have a set of jumper (or booster) cables and a second vehicle
with a 12-volt battery, you can jump start your vehicle by following the
steps below.
Open the hood. (
Remove the engine cover.
Pull up the both ends of the cover
vertically.
The following procedures may be used to start the hybrid sys-
tem if the vehicle’s 12-volt battery is discharged.
You can also call your Toyota dealer or a qualified repair shop.
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
651
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
Connect the jumper cables according to the following procedure:
Connect a positive jumper cable clamp to the positive (+) battery
terminal on your vehicle.
Connect the clamp on the other end of the positive cable to the
positive (+) battery terminal on the second vehicle.
Connect a negative cable clamp to the negative (-) battery termi-
nal on the second vehicle.
Connect the clamp at the other end of the negative cable to a
solid, stationary, unpainted metallic point away from the 12-volt
battery and any moving parts, as shown in the illustration.
Start the engine of the second vehicle. Increase the engine speed
slightly and maintain at that level for approximately 5 minutes to
recharge the 12-volt battery of your vehicle.
Maintain the engine speed of the second vehicle and start the
hybrid system of your vehicle by turning the power switch to ON
mode.
Make sure the “READY” indicator comes on. If the indicator light
does not come on, contact your Toyota dealer.
3
1
2
3
4
3
2
4
1
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
652
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
Once the hybrid system has started, remove the jumper cables in
the exact reverse order from which they were connected.
To install the engine cover, conduct the removal procedure in
reverse. After installing, check that the fixed pins are inserted
securely.
Once the hybrid system starts, have the vehicle inspected at your
Toyota dealer as soon as possible.
■
When opening the cover of the positive (+) battery terminal
■
Starting the hybrid system when the 12-volt battery is discharged
The hybrid system cannot be started by push-starting.
■
To prevent 12-volt battery discharge
●
Turn off the headlights and the audio system while the hybrid system is off.
●
Turn off any unnecessary electrical components when the vehicle is running
at a low speed for an extended period, such as in heavy traffic.
■
When the 12-volt battery is removed or discharged
●
Information stored in the ECU is cleared. When the 12-volt battery is
depleted, have the vehicle inspected at your Toyota dealer.
●
Some systems may require initialization. (
■
When removing the 12-volt battery terminals
When the 12-volt battery terminals are removed, the information stored in the
ECU is cleared. Before removing the 12-volt battery terminals, contact your
Toyota dealer.
■
Charging the 12-volt battery
The electricity stored in the 12-volt battery will discharge gradually even when
the vehicle is not in use, due to natural discharge and the draining effects of
certain electrical appliances. If the vehicle is left for a long time, the 12-volt
battery may discharge, and the hybrid system may be unable to start. (The
12-volt battery recharges automatically while the hybrid system is operating.)
7
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
653
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
■
When recharging or replacing the 12-volt battery
●
In some cases, it may not be possible to unlock the doors using the smart
key system when the 12-volt battery is discharged. Use the wireless remote
control or the mechanical key to lock or unlock the doors.
●
The hybrid system may not start on the first attempt after the 12-volt battery
has recharged but will start normally after the second attempt. This is not a
malfunction.
●
The power switch mode is memorized by the vehicle. When the 12-volt bat-
tery is reconnected, the system will return to the mode it was in before the
12-volt battery was discharged. Before disconnecting the 12-volt battery,
turn the power switch off.
If you are unsure what mode the power switch was in before the 12-volt bat-
tery discharged, be especially careful when reconnecting the 12-volt battery.
●
If the 12-volt battery discharges while the shift position is in P, it may not be
possible to shift the shift position to other positions. In this case, the vehicle
cannot be towed without lifting both front wheels because the front wheels
will be locked. (
■
When replacing the 12-volt battery
●
Use a 12-volt battery that conforms to European regulations.
●
Use a 12-volt battery that the case size is same as the previous one (LN1),
20 hour rate capacity (20HR) is equivalent (45Ah) or greater, and perfor-
mance rating (CCA) is equivalent (295A) or greater.
• If the sizes differ, the 12-volt battery cannot be properly secured.
• If the 20 hour rate capacity is low, even if the time period where the vehi-
cle is not used is a short time, the 12-volt battery may discharge and the
hybrid system may not be able to start.
●
For details, consult your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
654
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
WARNING
■
When removing the 12-volt battery terminals
Always remove the negative (-) terminal first. If the positive (+) terminal con-
tacts any metal in the surrounding area when the positive (+) terminal is
removed, a spark may occur, leading to a fire in addition to electrical shocks
and death or serious injury.
■
Avoiding 12-volt battery fires or explosions
Observe the following precautions to prevent accidentally igniting the flam-
mable gas that may be emitted from the 12-volt battery:
●
Make sure each jumper cable is connected to the correct terminal and that
it is not unintentionally in contact with any other than the intended terminal.
●
Do not allow the other end of the jumper cable connected to the “+” termi-
nal to come into contact with any other parts or metal surfaces in the area,
such as brackets or unpainted metal.
●
Do not allow the + and - clamps of the jumper cables to come into contact
with each other.
●
Do not smoke, use matches, cigarette lighters or allow open flame near
the 12-volt battery.
■
12-volt battery precautions
The 12-volt battery contains poisonous and corrosive acidic electrolyte,
while related parts contain lead and lead compounds. Observe the following
precautions when handling the 12-volt battery:
●
When working with the 12-volt battery, always wear safety glasses and
take care not to allow any battery fluids (acid) to come into contact with
skin, clothing or the vehicle body.
●
Do not lean over the 12-volt battery.
●
In the event that battery fluid comes into contact with the skin or eyes,
immediately wash the affected area with water and seek medical attention.
Place a wet sponge or cloth over the affected area until medical attention
can be received.
●
Always wash your hands after handling the 12-volt battery support, termi-
nals, and other battery-related parts.
●
Do not allow children near the 12-volt battery.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
655
7-2. Steps to take in an emergency
PRIUS_OM_OM47E09U_(U)
7
Wh
en tro
NOTICE
■
When handling jumper cables
When connecting the jumper cables, ensure that they do not become entan-
gled in the cooling fans, etc.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст