Toyota Avalon Hybrid (2022 year). Manual in english — page 18
526
8-1. Specifications
Engine
Model
A25A-FXS
Type
4-cylinder in line, 4-cycle, gasoline
Bore and stroke
3.44 4.07 in. (87.5 103.4 mm)
Displacement
151.8 cu. in. (2487 cm3)
Valve clearance
Automatic adjustment
Fuel
Fuel type
Unleaded gasoline only
Octane rating
87 (Research Octane Number 91) or higher
Fuel tank capacity
13 gal. (49.3 L, 10.8 Imp. gal.)
(Reference)
Electric motor (Traction motor)
Type
Permanent magnet synchronous motor
Maximum output
88 kW
Maximum torque
149 ft•lbf (202 N•m, 20.6 kgf•m)
Hybrid battery (Traction battery)
Type
Lithium-ion battery
Voltage
3.7 V/cell
Capacity
4.0 Ah
Quantity
70 cells
Nominal voltage
259 V
8-1. Specifications
527
Lubrication system
Oil capacity
(Drain and refill ―
reference*)
With filter
4.8 qt. (4.5 L, 4.0 Imp. qt.)
Without filter
4.4 qt. (4.2 L, 3.7 Imp. qt.)
*: The engine oil capacity is a reference quantity to be used when changing
the engine oil. Warm up the engine and turn off the hybrid system, wait
more than 5 minutes, and check the oil level on the dipstick.
■ Engine oil selection
“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use
Toyota approved “Toyota Genuine Motor Oil” or equivalent to sat-
isfy the following grade and viscosity.
Oil grade: ILSAC GF-6B multigrade engine oil
Recommended viscosity: SAE 0W-16
SAE 0W-16 is the best choice for
good fuel economy and good start-
ing in cold weather.
If SAE 0W-16 is not available, SAE
0W-20 oil may be used. However,
it must be replaced with SAE 0W-
16 at the next oil change.
Outside temperature
Oil viscosity (0W-16 is explained here as an example):
• The 0W in 0W-16 indicates the characteristic of the oil which allows cold
8
startability. Oils with a lower value before the W allow for easier starting of
the engine in cold weather.
• The 16 in 0W-16 indicates the viscosity characteristic of the oil when the
oil is at high temperature. An oil with a higher viscosity (one with a higher
value) may be better suited if the vehicle is operated at high speeds, or
under extreme load conditions.
528
8-1. Specifications
How to read oil container label:
API registered mark is added to
some oil containers to help you
select the oil you should use.
Cooling system
Gasoline engine
Capacity
6.4 qt. (6.1 L, 5.4 Imp. qt.)
(Reference)
Power control unit
1.9 qt. (1.8 L, 1.6 Imp. qt.)
Use either of the following:
•
“Toyota Super Long Life Coolant”
• Similar high-quality ethylene glycol-based
Coolant type
non-silicate, non-amine, non-nitrite, and
non-borate coolant with long-life hybrid
organic acid technology
Do not use plain water alone.
Ignition system
Spark plug
Make
DENSO FC16HR-Q8
Gap
0.031 in. (0.8 mm)
NOTICE
■ Iridium-tipped spark plugs
Use only iridium-tipped spark plugs. Do not adjust spark plug gap.
8-1. Specifications
529
Electrical system
12-volt battery
Open voltage at
12.0 V or higher
68F (20C):
If the voltage is lower than the standard value,
charge the battery.
(When checking the voltage, after turning the
power switch off, wait for 30 seconds with the
high beam headlights illuminated, then turn the
high beam headlights off and check the voltage.)
Charging rates
5 A max.
Hybrid transmission
Fluid capacity*
4.1 qt. (3.9 L, 3.4 Imp. qt.)
Fluid type
Toyota Genuine ATF WS
*: The fluid capacity is a reference quantity.
If replacement is necessary, contact your Toyota dealer.
NOTICE
■Hybrid transmission fluid type
Using transmission fluid other than the above type may cause abnormal
noise or vibration, or ultimately damage the transmission of your vehicle.
Brakes
Pedal clearance*
3.3 in. (85 mm)
8
Pedal free play
0.04 0.24 in. (1 6 mm)
Brake pad wear limit
0.04 in. (1.0 mm)
SAE J1703 or FMVSS No.116 DOT 3
Fluid type
SAE J1704 or FMVSS No.116 DOT 4
*: Minimum pedal clearance when depressed with a force of 67 lbf (300 N, 31
kgf) while the hybrid system is operating.
Steering
Free play
Less than 1.2 in. (30 mm)
530
8-1. Specifications
Tires and wheels
17-inch tires
Tire size
215/55R17 94V, T155/70D17 110M
Driving under normal conditions
Front:
35 psi (240 kPa, 2.4 kgf/cm2 or bar)
Rear:
35 psi (240 kPa, 2.4 kgf/cm2 or bar)
Spare:
Tire inflation pressure
60 psi (420 kPa, 4.2 kgf/cm2 or bar)
(Recommended cold
tire
Driving at high speeds (above 100 mph
inflation pressure)
[160 km/h])
(in countries where such
speeds are permitted by law)
Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to
the front tires and rear tires. Never
exceed the maximum cold tire inflation
pressure indicated on the tire sidewall.
Wheel size
17 7 1/2 J, 17 4 T (compact spare)
Wheel nut torque
76 ft•lbf (103 N•m, 10.5 kgf•m)
18-inch tires
Tire size
235/45R18 94V, T155/70D17 110M
Driving under normal conditions
Front:
35 psi (240 kPa, 2.4 kgf/cm2 or bar)
Rear:
35 psi (240 kPa, 2.4 kgf/cm2 or bar)
Spare:
Tire inflation pressure
60 psi (420 kPa, 4.2 kgf/cm2 or bar)
(Recommended cold
tire
Driving at high speeds (above 100 mph
inflation pressure)
[160 km/h])
(in countries where such
speeds are permitted by law)
Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to
the front tires and rear tires. Never
exceed the maximum cold tire inflation
pressure indicated on the tire sidewall.
Wheel size
18 8 J, 17 4 T (compact spare)
Wheel nut torque
76 ft•lbf (103 N•m, 10.5 kgf•m)
8-1. Specifications
531
19-inch tires
Tire size
235/40R19 92V, T155/70D17 110M
Driving under normal conditions
Front:
35 psi (240 kPa, 2.4 kgf/cm2 or bar)
Rear:
35 psi (240 kPa, 2.4 kgf/cm2 or bar)
Spare:
Tire inflation pressure
60 psi (420 kPa, 4.2 kgf/cm2 or bar)
(Recommended cold
tire
Driving at high speeds (above 100 mph
inflation pressure)
[160 km/h])
(in countries where such
speeds are permitted by law)
Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to
the front tires and rear tires. Never
exceed the maximum cold tire inflation
pressure indicated on the tire sidewall.
Wheel size
19 8 J, 17 4 T (compact spare)
Wheel nut torque
76 ft•lbf (103 N•m, 10.5 kgf•m)
Light bulbs*
Light bulbs
Bulb No.
W
Type
Door courtesy lights
168
5
A
Interior
Vanity lights
7065
1.4
B
Trunk light
5
A
A: Wedge base bulbs
B: Double end bulbs
8
*: Light bulbs not listed in this table are LED bulbs.
532
8-1. Specifications
Fuel information
You must only use unleaded gasoline.
Select octane rating 87 (Research Octane Number 91) or higher.
Use of unleaded gasoline with an octane rating lower than 87
may result in engine knocking. Persistent knocking can lead to
engine damage.
At minimum, the gasoline you use should meet the specifications of
ASTM D4814 in the U.S.A..
■ Gasoline quality
In very few cases, driveability problems may be caused by the brand of gaso-
line you are using. If driveability problems persist, try changing the brand of
gasoline. If this does not correct the problem, consult your Toyota dealer.
■ Recommendation of the use of gasoline containing detergent additives
● Toyota recommends the use of gasoline that contains detergent additives to
avoid the build-up of engine deposits.
● All gasoline sold in the U.S.A. contains minimum detergent additives to
clean and/or keep clean intake systems, per EPA’s lowest additives concen-
tration program.
● Toyota strongly recommends the use of Top Tier Detergent Gasoline. For
more information on Top Tier Detergent Gasoline and a list of marketers,
please go to the official website www.toptiergas.com.
8-1. Specifications
533
■ Recommendation of the use of low emissions gasoline
Gasolines containing oxygenates such as ethers and ethanol, as well as
reformulated gasolines, are available in some cities. These fuels are typically
acceptable for use, providing they meet other fuel requirements.
Toyota recommends these fuels, since the formulations allow for reduced
vehicle emissions.
■Non-recommendation of the use of blended gasoline
● Use only gasoline containing up to 15%
DO NOT use gasoline contain-
ethanol.
ing more than 15% ethanol.
DO NOT use any flex-fuel or gasoline
that could contain more than 15% etha-
nol, including from any pump labeled
(30% ethanol)
E30, E50, E85 (which are only some
(50% ethanol)
examples of fuel containing more than
15% ethanol).
(85% ethanol)
● If you use gasohol in your vehicle, be sure that it has an octane rating no
lower than 87.
● Toyota does not recommend the use of gasoline containing methanol.
■Non-recommendation of the use of gasoline containing MMT
Some gasoline contains an octane enhancing additive called MMT (Methylcy-
clopentadienyl Manganese Tricarbonyl).
Toyota does not recommend the use of gasoline that contains MMT. If fuel
containing MMT is used, your emission control system may be adversely
8
affected.
The malfunction indicator lamp on the instrument cluster may come on. If this
happens, contact your Toyota dealer for service.
■ If your engine knocks
● Consult your Toyota dealer.
● You may occasionally notice light knocking for a short time while accelerat-
ing or driving uphill. This is normal and there is no need for concern.
534
8-1. Specifications
NOTICE
■Notice on fuel quality
● Do not use improper fuels. If improper fuels are used, the engine will be
damaged.
● Do not use leaded gasoline.
Leaded gasoline can cause damage to your vehicle’s three-way catalytic
converters causing the emission control system to malfunction.
● Do not use gasohol other than the type previously stated.
Other gasohol may cause fuel system damage or vehicle performance
problems.
● Using unleaded gasoline with an octane number or rating lower than the
level previously stated will cause persistent heavy knocking.
At worst, this will lead to engine damage.
■ Fuel-related poor driveability
If poor driveability (poor hot starting, vaporization, engine knocking, etc.) is
encountered after using a different type of fuel, discontinue the use of that
type of fuel.
■ When refueling with gasohol
Take care not to spill gasohol. It can damage your vehicle’s paint.
8-1. Specifications
535
Tire information
Typical tire symbols
Full-size tire
Compact spare tire
8
536
8-1. Specifications
1
Tire size (P. 538)
2
Summer tires or all season tires (P. 443)
An all season tire has “M+S” on the sidewall. A tire not marked “M+S”
is a summer tire.
3
TUBELESS or TUBE TYPE
A tubeless tire does not have a tube and air is directly put into the tire.
A tube type tire has a tube inside the tire and the tube maintains the air
pressure.
4
Radial tires or bias-ply tires
A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL”
is a bias-ply tire.
5
DOT and Tire Identification Number (TIN) (P. 537)
6
Location of treadwear indicators (P. 437)
7
Uniform tire quality grading
For details, see “Uniform Tire Quality Grading” that follows.
8
Maximum cold tire inflation pressure (P. 530)
This means the pressure to which a tire may be inflated.
9
Load limit at maximum cold tire inflation pressure (P. 442)
10
Tire ply composition and materials
Plies are layers of rubber-coated parallel cords. Cords are the strands
which form the plies in a tire.
“TEMPORARY USE ONLY”
11
A compact spare tire is identified by the phrase “TEMPORARY USE
ONLY” molded on its sidewall. This tire is designed for temporary
emergency use only.
8-1. Specifications
537
Typical DOT and Tire Identification Number (TIN)
Type A
Type B
1
DOT symbol*
2
Tire Identification Number (TIN)
3
Tire manufacturer’s identification mark
4
Tire size code
5
Manufacturer’s optional tire type code (3 or 4 letters)
6
Manufacturing week
7
Manufacturing year
8
Manufacturer’s code
*: The DOT symbol certifies that the tire conforms to applicable Federal
Motor Vehicle Safety Standards.
8
538
8-1. Specifications
Tire size
■ Typical tire size information
The illustration indicates typical
tire size.
1
Tire use
(P = Passenger car [some-
times omitted],
T = Temporary use)
2
Section width (millimeters)
3
Aspect ratio
(tire height to section width)
4
Tire construction code (R = Radial, D = Diagonal)
5
Wheel diameter (inches)
6
Load index (2 digits or 3 digits)
7
Speed symbol (alphabet with one letter)
■ Tire dimensions
1
Section width
2
Tire height
3
Wheel diameter
8-1. Specifications
539
Tire section names
1
Bead
2
Sidewall
3
Shoulder
4
Tread
5
Belt
6
Inner liner
7
Reinforcing rubber
8
Carcass
9
Rim lines
10
Bead wires
11
Chafer
8
540
8-1. Specifications
Uniform Tire Quality Grading
This information has been prepared in accordance with regulations
issued by the National Highway Traffic Safety Administration of the
U.S. Department of Transportation.
It provides the purchasers and/or prospective purchasers of Toyota
vehicles with information on uniform tire quality grading.
Your Toyota dealer will help answer any questions you may have as
you read this information.
■ DOT quality grades
All passenger vehicle tires must conform to Federal Safety Require-
ments in addition to these grades. Quality grades can be found
where applicable on the tire sidewall between tread shoulder and
maximum section width.
For example: Treadwear 200 Traction AA Temperature A
■ Treadwear
The treadwear grade is a comparative rating based on the wear
rate of the tire when tested under controlled conditions on a speci-
fied government test course.
For example, a tire graded 150 would wear one and a half (1 - 1/2)
times as well on the government course as a tire graded 100.
The relative performance of tires depends upon the actual condi-
tions of their use. Performance may differ significantly from the norm
due to variations in driving habits, service practices and differences
in road characteristics and climate.
■ Traction AA, A, B, C
The traction grades, from highest to lowest, are AA, A, B and C,
and they represent the tire’s ability to stop on wet pavement as
measured under controlled conditions on specified government test
surfaces of asphalt and concrete.
A tire marked C may have poor traction performance.
Warning: The traction grade assigned to this tire is based on braking
(straight ahead) traction tests and does not include cornering (turn-
ing) traction.
8-1. Specifications
541
■ Temperature A, B, C
The temperature grades are A (the highest), B, and C, representing
the tire’s resistance to the generation of heat and its ability to dissi-
pate heat when tested under controlled conditions on a specified
indoor laboratory test wheel.
Sustained high temperature can cause the material of the tire to
degenerate and reduce tire life, and excessive temperature can lead
to sudden tire failure.
Grade C corresponds to a level of performance which all passenger
car tires must meet under the Federal Motor Vehicle Safety Stan-
dard No. 109.
Grades B and A represent higher levels of performance on the labo-
ratory test wheel than the minimum required by law.
Warning: The temperature grades of a tire assume that it is properly
inflated and not overloaded.
Excessive speed, underinflation, or excessive loading, either sepa-
rately or in combination, can cause heat buildup and possible tire
failure.
8
542
8-1. Specifications
Glossary of tire terminology
Tire related term
Meaning
Tire pressure when the vehicle has been
Cold tire inflation pres-
parked for three hours or more, or has not
sure
been driven more than 1 mile or 1.5 km under
that condition
The maximum cold inflated pressure to which
Maximum
inflation
a tire may be inflated, shown on the sidewall
pressure
of the tire
Recommended infla-
Cold tire inflation pressure recommended by a
tion pressure
manufacturer
The combined weight (in excess of those stan-
dard items which may be replaced) of hybrid
transmission, power steering, power brakes,
Accessory weight
power windows, power seats, radio and
heater, to the extent that these items are avail-
able as factory-installed equipment (whether
installed or not)
The weight of a motor vehicle with standard
equipment, including the maximum capacity of
Curb weight
fuel, oil and coolant, and if so equipped, air
conditioning and additional weight optional
engine
The sum of:
(a) Curb weight
Maximum loaded vehi-
(b) Accessory weight
cle weight
(c) Vehicle capacity weight
(d) Production options weight
150 lb. (68 kg) times the number of occupants
Normal
occupant
specified in the second column of Table 1*
weight
that follows
Distribution of occupants in a vehicle as speci-
Occupant distribution
fied in the third column of Table 1* below
8-1. Specifications
543
Tire related term
Meaning
The combined weight of installed regular pro-
duction options weighing over 5 lb. (2.3 kg) in
excess of the standard items which they
Production
options
replace, not previously considered in curb
weight
weight or accessory weight, including heavy
duty brakes, ride levelers, roof rack, heavy
duty 12-volt battery, and special trim
A metal support for a tire or a tire and tube
Rim
assembly upon which the tire beads are
seated
Rim diameter
Nominal diameter of the bead seat
(Wheel diameter)
Rim size designation
Rim diameter and width
The industry manufacturer’s designation for a
Rim type designation
rim by style or code
Rim width
Nominal distance between rim flanges
Vehicle
capacity
The rated cargo and luggage load plus 150 lb.
weight
(Total
load
(68 kg) times the vehicle’s designated seating
capacity)
capacity
The load on an individual tire that is deter-
Vehicle maximum load
mined by distributing to each axle its share of
on the tire
the maximum loaded vehicle weight, and
dividing by two
The load on an individual tire that is deter-
mined by distributing to each axle its share of
Vehicle normal load on
curb weight, accessory weight, and normal
8
the tire
occupant weight
(distributed in accordance
with Table 1* below), and dividing by two
The surface area of the rim not covered by the
Weather side
inflated tire
The part of the tire that is made of steel wires,
Bead
wrapped or reinforced by ply cords and that is
shaped to fit the rim
A breakdown of the bond between compo-
Bead separation
nents in the bead
544
8-1. Specifications
Tire related term
Meaning
A pneumatic tire in which the ply cords that
extend to the beads are laid at alternate
Bias ply tire
angles substantially less than 90 degrees to
the centerline of the tread
The tire structure, except tread and sidewall
Carcass
rubber which, when inflated, bears the load
The breaking away of pieces of the tread or
Chunking
sidewall
Cord
The strands forming the plies in the tire
The parting of cords from adjacent rubber
Cord separation
compounds
Any parting within the tread, sidewall, or inner-
Cracking
liner of the tire extending to cord material
A pneumatic tire with an inverted flange tire
and rim system in which the rim is designed
with rim flanges pointed radially inward and
CT
the tire is designed to fit on the underside of
the rim in a manner that encloses the rim
flanges inside the air cavity of the tire
A tire designed to operate at higher loads and
Extra load tire
at higher inflation pressures than the corre-
sponding standard tire
Groove
The space between two adjacent tread ribs
The layer(s) forming the inside surface of a
Innerliner
tubeless tire that contains the inflating medium
within the tire
The parting of the innerliner from cord material
Innerliner separation
in the carcass
(a)The sidewall that contains a whitewall,
bears white lettering, or bears manufacturer,
brand, and/or model name molding that is
higher or deeper than the same molding on
Intended
outboard
the other sidewall of the tire, or
sidewall
(b)The outward facing sidewall of an asym-
metrical tire that has a particular side that
must always face outward when mounted on a
vehicle
8-1. Specifications
545
Tire related term
Meaning
A tire designated by its manufacturer as pri-
Light truck (LT) tire
marily intended for use on lightweight trucks
or multipurpose passenger vehicles
The maximum load that a tire is rated to carry
Load rating
for a given inflation pressure
The load rating for a tire at the maximum per-
Maximum load rating
missible inflation pressure for that tire
Maximum permissible
The maximum cold inflation pressure to which
inflation pressure
a tire may be inflated
The rim on which a tire is fitted for physical
Measuring rim
dimension requirements
Any parting at any junction of tread, sidewall,
Open splice
or innerliner that extends to cord material
Outer diameter
The overall diameter of an inflated new tire
The linear distance between the exteriors of
the sidewalls of an inflated tire, including ele-
Overall width
vations due to labeling, decorations, or protec-
tive bands or ribs
A tire intended for use on passenger cars,
multipurpose passenger vehicles, and trucks,
Passenger car tire
that have a gross vehicle weight rating
(GVWR) of 10,000 lb. or less.
Ply
A layer of rubber-coated parallel cords
A parting of rubber compound between adja-
Ply separation
cent plies
8
A mechanical device made of rubber, chemi-
cals, fabric and steel or other materials, that,
Pneumatic tire
when mounted on an automotive wheel, pro-
vides the traction and contains the gas or fluid
that sustains the load
A pneumatic tire in which the ply cords that
Radial ply tire
extend to the beads are laid at substantially 90
degrees to the centerline of the tread
A tire designed to operate at higher loads and
Reinforced tire
at higher inflation pressures than the corre-
sponding standard tire
546
8-1. Specifications
Tire related term
Meaning
The linear distance between the exteriors of
the sidewalls of an inflated tire, excluding ele-
Section width
vations due to labeling, decoration, or protec-
tive bands
That portion of a tire between the tread and
Sidewall
bead
The parting of the rubber compound from the
Sidewall separation
cord material in the sidewall
A tire that attains a traction index equal to or
greater than 110, compared to the ASTM E-
1136 Standard Reference Test Tire, when
using the snow traction test as described in
ASTM F-1805-00, Standard Test Method for
Snow tire
Single Wheel Driving Traction in a Straight
Line on Snow-and Ice-Covered Surfaces, and
which is marked with an Alpine Symbol (
)
on at least one sidewall
The rim on which a tire is fitted for testing, and
Test rim
may be any rim listed as appropriate for use
with that tire
That portion of a tire that comes into contact
Tread
with the road
A tread section running circumferentially
Tread rib
around a tire
Tread separation
Pulling away of the tread from the tire carcass
The projections within the principal grooves
Treadwear indicators
designed to give a visual indication of the
(TWI)
degrees of wear of the tread
The fixture used to hold the wheel and tire
Wheel-holding fixture
assembly securely during testing
*: Table 1 Occupant loading and distribution for vehicle normal load for
various designated seating capacities
8-1. Specifications
547
Designated seating
Occupant distribution
Vehicle normal load,
capacity, Number of
in a normally loaded
Number of occupants
occupants
vehicle
2 through 4
2
2 in front
2 in front, 1 in second
5 through 10
3
seat
2 in front, 1 in second
11 through 15
5
seat, 1 in third seat, 1
in fourth seat
2 in front, 2 in second
16 through 20
7
seat, 2 in third seat, 1
in fourth seat
8
548
8-2. Customization
Customizable features
Your vehicle includes a variety of electronic features that can be
personalized to suit your preferences. The settings of these fea-
tures can be changed using the multi-information display, on the
audio system screen, or at your Toyota dealer.
Customizing vehicle features
When customizing vehicle features, ensure that the vehicle is parked
in a safe place with the shift lever in P and the parking brake set.
■ Changing on the audio system screen
1
Press the “MENU” button.
2
Select “Setup” on the “Menu” screen.
3
Select “General” or “Vehicle” on the “Setup” screen.
Various setting can be changed. Refer to the list of settings that can
be changed for details.
■ Changing using the multi-information display
P. 111
8-2. Customization
549
Customizable features
Some function settings are changed simultaneously with other func-
tions being customized. Contact your Toyota dealer for further details.
1
Settings that can be changed on the audio system screen
2
Settings that can be changed by your Toyota dealer
Definition of symbols: O = Available, — = Not available
8
550
8-2. Customization
■ Gauges, meters and multi-information display (P. 98, 102)
Function
Default setting
Customized setting
1
2
French
Language
English
O
—
Spanish
miles (MPG Imperial)
Units*
miles (MPG US)
km (L/100 km)
O
—
km (km/L)
On
(when the vehicle is
Convenience services
On
stopped)
O
O
(Suggestion function)
Off
*: The default setting varies according to country.
■ Door lock (P. 142, 148, 507)
Function
Default setting
Customized setting
1
2
Driver’s door
unlocked in one
Unlocking
using
a
All doors unlocked in
step, all doors
—
O
mechanical key
one step
unlocked in two
steps
Off
Shift position
Automatic door lock
linked door lock-
O
O
Speed linked door
ing operation
locking operation
Off
Shift position
linked door
Automatic door unlock
Driver’s door linked
O
O
unlocking opera-
door unlocking oper-
tion
ation
Locking/unlocking of the
trunk when all doors are
On
Off
—
O
locked/unlocked
8-2. Customization
551
■ Smart key system and wireless remote control
(P. 142, 148, 152)
Function
Default setting
Customized setting
1
2
Operating signal
5
Off to 7
O
O
(Buzzers)
Operation signal
On
Off
O
O
(Emergency flashers)
Time elapsed before
Off
automatic door lock
function is activated if
60 seconds
30 seconds
O
O
door is not opened after
being unlocked
120 seconds
Open door warning
On
Off
—
O
buzzer
■ Smart key system (P. 142, 148, 152)
Function
Default setting
Customized setting
1
2
Smart key system
On
Off
—
O
Time elapsed before
unlocking all the door
when gripping and hold-
2 seconds
Off
—
O
ing the driver’s door han-
dle
Number of consecutive
2 times
As many as desired
—
O
door lock operations
8
552
8-2. Customization
■ Wireless remote control (P. 138, 142, 148)
Function
Default setting
Customized setting
1
2
Wireless remote control
On
Off
—
O
Driver’s door
unlocked in one
All doors unlocked in
Unlocking operation
step, all doors
O
O
one step
unlocked in two
steps
One short press
Push twice
Trunk unlocking opera-
Press and hold
—
O
tion
(short)
Press and hold (long)
Off
Panic function
On
Off
—
O
Reservation lock
On
Off
O
O
■ Power windows and moon roof* (P. 177, 181)
Function
Default setting
Customized setting
1
2
Mechanical key linked
Off
On
—
O
operation
Wireless remote control
Off
On (open only)
—
O
linked operation
Wireless remote control
linked operation signal
On
Off
—
O
(buzzer)
*: If equipped
8-2. Customization
553
■ Moon roof* (P. 181)
Function
Default setting
Customized setting
1
2
Linked operation of com-
ponents when mechani-
Slide only
Tilt only
—
O
cal key is used
(open
only)
Linked operation of com-
ponents when wireless
Slide only
Tilt only
—
O
remote control is used
*: If equipped
■ Driving position memory* (P. 163)
Function
Default setting
Customized setting
1
2
Selecting doors linked to
the memory recall func-
Driver’s door
All doors
—
O
tion
Off
Driver’s seat movement
Standard
O
O
when exiting the vehicle
Partial
Telescopic only
Steering wheel move-
Tilt only
Tilt & telescopic
O
O
ment
Off
*: If equipped
■ Automatic light control system (P. 222)
8
Function
Default setting
Customized setting
1
2
Light sensor sensitivity
Standard
-2 to 2
O
O
Time elapsed before
Off
headlights automatically
30 seconds
60 seconds
O
O
turn off after doors are
closed
90 seconds
554
8-2. Customization
■ Lights (P. 222)
Function
Default setting
Customized setting
1
2
Daytime running light
On
Off
O
O
system
Welcome lighting
On
Off
—
O
Windshield wiper linked
On
Off
—
O
headlight illumination
■ Intuitive parking assist* (P. 313)
Function
Default setting
Customized setting
1
2
Detection distance of the
Far
Near
—
O
front center sensor
Detection distance of the
Far
Near
—
O
rear center sensor
*: If equipped
■ BSM (Blind Spot Monitor) (P. 297)
Function
Default setting
Customized setting
1
2
Outside rear view mirror
Bright
Dim
—
O
indicator brightness
Early
Alert sensitivity for pres-
Late
ence of approaching
Intermediate
—
O
vehicle
Only when vehicle
detected in blind spot
■ RCTA (Rear Cross Traffic Alert) (P. 297)
Function
Default setting
Customized setting
1
2
Buzzer volume
2
1 to 3
—
O
8-2. Customization
555
■ Automatic air conditioning system (P. 360)
Function
Default setting
Customized setting
1
2
A/C auto switch opera-
Auto
Manual
O
O
tion
■ Illumination (P. 374)
Function
Default setting
Customized setting
1
2
Off
Time elapsed before
15 seconds
7.5 seconds
O
O
lights turn off
30 seconds
Operation after
the
On
Off
—
O
power switch turned off
Operation when the
On
Off
—
O
doors are unlocked
Operation when you
approach the vehicle
On
Off
—
O
with the electronic key
on your person
Ambient lights*
On
Off
—
O
*: If equipped
8
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст