Toyota Sequoia (2005). Manual — part 390
H23795
H23974
H01001
H23987
D+
D–
Color: Orange
D Squib
Spiral
Cable
A
B
C
D
E
F
Airbag
Sensor
Assembly
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–1355
1549
2
Check connector.
CHECK:
Check that the spiral cable connectors (on the steering wheel pad side) are not damaged.
OK:
The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
NG
Replace spiral cable (see page
OK
3
Check D squib circuit (short).
PREPARATION:
Release the activation prevention mechanism built into con-
nector ”B” (see page
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – D–
Always
1 M
Ω
or higher
NG
Go to step 13.
OK
Go to step 10.
H23795
H23974
H01001
H23987
D+
D–
Color: Orange
D Squib
Spiral
Cable
A
B
C
D
E
F
Airbag
Sensor
Assembly
H23795
H23974
H01001
H23987
D+
D–
Color: Orange
D Squib
Spiral
Cable
A
B
C
D
E
F
Airbag
Sensor
Assembly
DI–1356
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
1550
4
Check D squib circuit (open).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – D–
Always
Below 1
Ω
NG
Go to step 15.
OK
Go to step 11.
5
Check D squib circuit (short to ground).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – Body ground
Always
1 M
Ω
or higher
D– – Body ground
Always
1 M
Ω
or higher
NG
Go to step 17.
OK
Go to step 11.
H23795
H23974
H01001
H23987
D+
D–
Color: Orange
D Squib
Spiral
Cable
A
B
C
D
E
F
Airbag
Sensor
Assembly
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–1357
1551
6
Check D squib (short to B+).
PREPARATION:
Connect the negative (–) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a)
Turn the ignition switch to the ON position.
(b)
Measure the voltage according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – Body ground
Ignition switch ON
Below 1 V
D– – Body ground
Ignition switch ON
Below 1 V
NG
Go to step 19.
OK
Go to step 11.
7
Check connector.
CHECK:
Check that the spiral cable connectors (on the steering wheel pad side) are not damaged.
OK:
The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
NG
Replace spiral cable (see page
OK
H23795
H23974
H01001
H23987
D+
D–
Color: Orange
D Squib
Spiral
Cable
A
B
C
D
E
F
Airbag
Sensor
Assembly
DI–1358
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
1552
8
Check D squib circuit.
PREPARATION:
Connect the negative (–) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a)
Turn the ignition switch to the ON position.
(b)
Measure the voltage according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – Body ground
Ignition switch ON
Below 1 V
D– – Body ground
Ignition switch ON
Below 1 V
PREPARATION:
(a)
Turn the ignition switch to the LOCK position.
(b)
Disconnect the negative (–) terminal cable from the bat-
tery, and wait for at least 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – D–
Always
Below 1
Ω
D+ – Body ground
Always
1 M
Ω
or higher
D– – Body ground
Always
1 M
Ω
or higher
PREPARATION:
Release the activation prevention mechanism built into the con-
nector ”B” (see page
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
D+ – D–
Always
1 M
Ω
or higher
NG
Go to step 21.
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст