Toyota Sequoia (2005). Manual — part 252
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
DI–803
997
6
Problem Symptoms Table (See page
)
Go to step 8
7
Circuit Inspection (See page
NEXT
8
Repair
NEXT
9
Confirmation Test
NEXT
End
DIDJY–01
Inspector’s
Name
:
Customer’s Name
Production Date
VIN
Licence Plate No.
Odometer Reading
/ /
/ /
Frequency of Problem Occurrence
/ /
Continuous
Intermittent ( times a day)
In spite of abnormal low tire pressure, the warning lamp does not
come on.
The warning lamp was lit and the tire was filled up with air, but
the warning lamp does not go off.
Remains ON
Does not come on
Check Item
Tire Pressure
Warning Lamp
Normal
Malfunction Code (Code )
Symptoms
km
miles
Tire Pressure Warning System Check Sheet
Tire Pressure
Warning Lamp
Abnormal
Tire
Tire Pressure
FR ( ) FL ( ) RR ( ) RL ( )
Tire Size
Tire Type
Tire Wear Condition
History of changing tires or wheels
When ( )
History of rotating tires
FR ( ) FL ( ) RR ( ) RL ( )
FR ( ) FL ( ) RR ( ) RL ( )
FR ( ) FL ( ) RR ( ) RL ( )
When ( )
DI–804
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
998
CUSTOMER PROBLEM ANALYSIS CHECK
DIDJZ–01
F19326
F19327
F19328
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
DI–805
999
REGISTRATION
1.
IN CASE OF TIRE PRESSURE MONITOR ECU REPLACEMENT
(a)
Read ID stored in the old ECU using the hand–held tester.
2.
IN CASE OF TIRE PRESSURE MONITOR VALVE SUB–ASSY AND/OR TIRE PRESSURE MON-
ITOR ECU REPLACEMENT
(a)
Read ID written on the tire pressure monitor valve.
3.
REGISTER TRANSMITTER ID
NOTICE:
It is necessary to register the transmitter ID in the tire pressure monitor ECU when replacing the tire
pressure monitor valve sub–assy and/or tire pressure monitor ECU.
(a)
Set the tire pressure of all wheels to the specified value.
Tire size
Front
Rear
Spare
P245 / 70 R 16
220 kPa (2.2 kgf/cm
2
, 32 psi)
240 kPa (2.4 kgf/cm
2
, 35 psi)
240 kPa (2.4 kgf/cm
2
, 35 psi)
P265 / 70 R 16
220 kPa (2.2 kgf/cm
2
, 32 psi)
220 kPa (2.2 kgf/cm
2
, 32 psi)
220 kPa (2.2 kgf/cm
2
, 32 psi)
P265 / 65 R 17
220 kPa (2.2 kgf/cm
2
, 32 psi)
220 kPa (2.2 kgf/cm
2
, 32 psi)
220 kPa (2.2 kgf/cm
2
, 32 psi)
(b)
Connect the hand–held tester to DLC3.
(c)
Turn the ignition switch to the ON position.
(d)
Read and write down the ID (ID1 to ID5) by using the
DATA LIST.
(e)
Select the REGIST TIRE following the hand–held tester
screen.
(UTILITY – REGIST TIRE)
(f)
Input the ID (ID1 to ID5) using the hand–held tester and
transmit it to the tire pressure monitor ECU.
(g)
Set the ID transmission condition to ”SUCCEEDED”.
HINT:
If the operations of steps (d) to (f) do not complete within 5 min.,
the mode will return to normal operation mode.
F19131
Registration Procedure
DI–806
–
DIAGNOSTICS
TIRE PRESSURE WARNING SYSTEM
1000
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст