Toyota Sequoia (2005). Manual — part 654
P20636
1.27 mm
Hexagon Wrench
A04454
1.27 mm
Hexagon Wrench
A23307
Turn
A23308
A23306
SST
EM–26
–
ENGINE MECHANICAL
TIMING BELT
2605
15.
SET TIMING BELT TENSIONER
(a)
Using a press, slowly press in the push rod using 981 –
9,807 N (100 – 1,000 kgf, 220 – 2,205 lbf) of pressure.
(b)
Align the holes of the push rod and housing, and pass a
1.27 mm hexagon wrench through the holes to keep the
setting position of the push rod.
(c)
Remove the belt tensioner from the press.
(d)
Install the dust boot to the belt tensioner.
16.
INSTALL TIMING BELT TENSIONER
(a)
Temporarily install the belt tensioner with the 2 bolts.
(b)
Alternately tighten the 2 bolts.
Torque: 26 N·m (270 kgf·cm, 19 ft·lbf)
(c)
Using pliers, remove the 1.27 mm hexagon wrench from
the belt tensioner.
17.
CHECK VALVE TIMING
(a)
Temporarily install the crankshaft pulley bolt.
(b)
Slowly turn the crankshaft pulley 2 revolutions from the
TDC to TDC.
NOTICE:
Always turn the crankshaft pulley clockwise.
(c)
Check that each pulley aligns with the timing marks as
shown in the illustration.
If the timing marks do not align, remove the timing belt and rein-
stall it.
18.
TIGHTEN CRANKSHAFT PULLEY BOLT
Using SST, install the pulley bolt.
SST
09213–70011 (90119–08216), 09330–00021
Torque: 245 N·m (2,500 kgf·cm, 181 ft·lbf)
A04455
(A)
(B)
A04330
A04329
–
ENGINE MECHANICAL
TIMING BELT
EM–27
2606
19.
INSTALL FAN BRACKET
Install the fan bracket with the 2 bolts and 2 nuts.
Torque:
12 mm head
16 N·m (160 kgf·cm, 12 ft·lbf) for (A)
14 mm head
32 N·m (330 kgf·cm, 24 ft·lbf) for (B)
HINT:
Each bolt length is indicated in the illustration.
Bolt Length:
106 mm (4.17 in.) for 12 mm head (A)
114 mm (4.49 in.) for 14 mm head (B)
20.
INSTALL A/C COMPRESSOR (See page
)
21.
INSTALL NO.2 TIMING BELT COVER
Install the No.2 timing belt cover with the 2 bolts.
Torque: 16 N·m (160 kgf·cm, 12 ft·lbf)
22.
INSTALL RH NO.3 TIMING BELT COVER
(a)
Fit the RH No.3 timing belt cover, matching it with the fan
bracket.
(b)
Install the RH No.3 timing belt cover with the 3 bolts and
nut.
Torque: 7.5 N·m (76 kgf·cm, 66 in.·lbf)
A04331
A08934
EM–28
–
ENGINE MECHANICAL
TIMING BELT
2607
23.
INSTALL LH NO.3 TIMING BELT COVER
(a)
Install the oil cooler pipe with the bolt and nut.
(b)
Run the camshaft position sensor wire through the LH
No.3 timing belt cover hole.
(c)
Fit the LH No.3 timing belt cover, matching it with the fan
bracket.
(d)
Install the LH No.3 timing belt cover with the 4 bolts and
nut.
Torque: 7.5 N·m (76 kgf·cm, 66 in.·lbf)
(e)
Install the wire grommet to the LH No.3 timing belt cover.
(f)
Install the camshaft position sensor connector to the con-
nector bracket.
(g)
Connect the camshaft position sensor connector.
(h)
Install the sensor wire to the wire clamp on the LH No.3
timing belt cover.
(i)
Install the engine wire to the 2 wire clamps on the LH No.3
timing belt cover.
24.
INSTALL DRIVE BELT IDLER PULLEY
Install the idler pulley and cover plate with the bolt.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
25.
INSTALL PS PUMP
Install the PS pump with the 3 bolts.
Torque: 17 N·m (175 kgf·cm, 13 ft·lbf)
26.
INSTALL FAN PULLEY, FAN, FLUID COUPLING
AND DRIVE BELT
(a)
Temporarily install the fan pulley, the fan, fluid coupling
assembly with the 4 nuts.
(b)
Install the drive belt. (See page
(c)
Tighten the 4 nuts holding the fluid coupling to the fan
bracket.
Torque: 29 N·m (296kgf·cm, 21 ft·lbf)
27.
INTAKE AIR CONNECTOR ASSEMBLY
28.
INSTALL THROTTLE BODY COVER
29.
INSTALL RADIATOR ASSEMBLY (See page
30.
FILL WITH ENGINE COOLANT
31.
START ENGINE AND CHECK FOR LEAKS
32.
RECHECK ENGINE COOLANT LEVEL
33.
INSTALL ENGINE UNDER COVER
EM1WZ–01
A21015
MAF Meter Wire
P/S Air
Hose
No.2 Fan Shroud
Radiator
Assembly
Fan Pulley
Drive Belt
A/C Compressor
Connector
Engine Under Cover (2WD)
A/C Compressor
Fan And Fluid Coupling
Assembly
Throttle Body Cover
Engine Under Cover
49 (500, 36)
x 4
N·m (kgf·cm, ft·lbf) : Specified torque
A/T Oil Cooler Hose
4WD:
Vacuum Hose
PCV Hose
Clip
12 (122, 9)
29 (296, 21)
Suction Hose
Intake Air Connector
x 5
29 (296, 21)
29 (296, 21)
–
ENGINE MECHANICAL
CYLINDER HEAD
EM–29
2608
CYLINDER HEAD
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст