Toyota Sequoia (2005). Manual — part 731
D13884
A750E:
A750F:
AT133–01
D13885
A750E:
A750F:
–
AUTOMATIC TRANSMISSION (A750E, A750F)
SPEED SENSOR
AT–5
2913
SPEED SENSOR
ON–VEHICLE REPAIR
1.
DISCONNECT NO. 1 VEHICLE SPEED SENSOR CON-
NECTOR
2.
REMOVE NO. 1 VEHICLE SPEED SENSOR
Remove the bolt and No.1 vehicle speed sensor.
3.
DISASSEMBLE NO. 1 VEHICLE SPEED SENSOR
(a)
Remove the O–ring from the speedometer driven gear
assembly.
(b)
Remove the clip and speedometer driven gear from the
speedometer driven gear sleeve.
4.
ASSEMBLE NO. 1 VEHICLE SPEED SENSOR
(a)
Install the speedometer driven gear and clip to the
speedometer driven gear sleeve.
(b)
Coat a new O–ring with ATF.
(c)
Install the O–ring to the speedometer driven gear assem-
bly.
5.
INSTALL NO. 1 VEHICLE SPEED SENSOR
Install the No.1 vehicle speed sensor with the bolt.
Torque:
A750E: 9.8 N·m (100 kgf·cm, 86 in.·lbf)
A750F: 11.5 N·m (117 kgf·cm, 8 ft·lbf)
6.
CONNECT NO. 1 VEHICLE SPEED SENSOR CON-
NECTOR
D14124
Speed Sensor NT
Speed Sensor SP2
D02395
D14124
Speed Sensor NT
Speed Sensor SP2
AT–6
–
AUTOMATIC TRANSMISSION (A750E, A750F)
SPEED SENSOR
2914
7.
DISCONNECT SPEED SENSOR NT AND SP2 CON-
NECTOR
8.
REMOVE SPEED SENSOR NT AND SP2
(a)
Remove the 2 bolts, speed sensors NT and SP2.
(b)
Remove 2 O–rings from the speed sensors NT and SP2.
9.
INSTALL SPEED SENSOR NT AND SP2
(a)
Coat 2 new O–rings with ATF and install them to the
speed sensors NT and SP2.
(b)
Install the speed sensors NT and SP2 with the 2 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
10.
CONNECT SPEED SENSOR NT AND SP2 CONNEC-
TOR
D13867
AT134–01
D12704
Orange
Blue
Clamp
Clamp
Bolt
Bolt
D12739
D12704
Orange
Blue
Clamp
Clamp
A
B
–
AUTOMATIC TRANSMISSION (A750E, A750F)
ATF TEMPERATURE SENSOR
AT–7
2915
ATF TEMPERATURE SENSOR
ON–VEHICLE REPAIR
1.
DRAIN AUTOMATIC TRANSMISSION FLUID
(a)
Remove the drain plug and gasket, and drain the ATF.
(b)
Install a new gasket and the drain plug.
Torque: 20 N·m (204 kgf·cm, 15 ft·lbf)
2.
REMOVE OIL PAN (See page
3.
REMOVE OIL STRAINER (See page
4.
REMOVE ATF TEMPERATURE SENSOR
(a)
Disconnect the 7 solenoid valve connectors.
(b)
Remove the 2 bolts, clamps and ATF temperature sen-
sors.
(c)
Disconnect the transmission wire connector.
(d)
Remove the bolt and the transmission wire harness.
5.
INSTALL ATF TEMPERATURE SENSOR
(a)
Install the transmission wire harness.
(b)
Install the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(c)
Connect the transmission wire connector.
(d)
Connect the 7 solenoid valve connectors.
(e)
Install the 2 ATF temperature sensors and clamps to the
valve body with the 2 bolts.
HINT:
In order to install the ATF temperature sensors properly, check
the wire harness color prior to installation.
Torque:
A: 11 N·m (112 kgf·cm, 8 ft·lbf)
B: 10 N·m (100 kgf·cm, 7 ft·lbf)
Bolt length:
Bolt A: 36 mm (1.42 in.)
Bolt B: 12 mm (0.47 in.)
Sensor wire harness:
Wire harness
Color
for linear control
Orange
for oil temp. warning lamp
Blue
6.
INSTALL OIL STRAINER (See page
)
D13866
AT–8
–
AUTOMATIC TRANSMISSION (A750E, A750F)
ATF TEMPERATURE SENSOR
2916
7.
INSTALL OIL PAN
HINT:
Remove any packing material, and be careful not to spill oil on
the contacting surfaces of the transmission case and the oil
pan.
Using a new gasket, install the oil pan with the 20 bolts.
Torque: 4.4 N·m (45 kgf·cm, 39 in·lbf)
8.
FILL WITH ATF AND CHECK ATF LEVEL
(a)
Remove the refill plug (See page
).
(b)
Fill with new fluid through the refill hole.
Fluid type: Toyota genuine ATF WS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст