Toyota Sequoia (2005). Manual — part 235
F16806
High (45
°)
Low (–45
°)
Normal (0
°)
Connector Front View:
SHG
SHRL
SHB
–
DIAGNOSTICS
AIR SUSPENSION SYSTEM
DI–735
929
5
Inspect height control sensor sub–assy.
PREPARATION:
(a)
Remove the height control sensor sub–assy.
(b)
Connect 3 dry batteries of 1.5 V in series.
CHECK:
Connect terminal 1 (SHB) to the batteries’ positive (+) terminal,
and terminal 3 (SHG) to the batteries’ negative (–) terminal,
then apply approximately 4.5 V between terminals 2 (SHRL)
and 3 (SHG) in the following conditions.
OK:
Position
Voltage
High (0
to 45
)
Approx. 2.25 to 4.05 V
Normal (0
)
Approx. 2.25 V
Low (0
to –45
)
Approx. 0.45 to 2.25 V
NG
Replace height control sensor sub–assy.
OK
Replace suspension control ECU
(See page
).
F19442
Suspension Control ECU
H16
Gate Solenoid Valve
(Height Control Valve)
W–L
8
BM1
SLRL
1
14
IN1
4
S25
BI
W–B
2
W–L
W–L
DI–736
–
DIAGNOSTICS
AIR SUSPENSION SYSTEM
930
DTC
C1733/33 Gate Solenoid Valve Circuit
CIRCUIT DESCRIPTION
The suspension control ECU opens the gate solenoid valve (height control valve) to lead the compressed
air to the height control cylinder (pneumatic cylinder) and to raise the vehicle height.
Further, the gate solenoid valve (height control valve) opens and closes the passage between the right and
left height control cylinders (pneumatic cylinders).
The height control valve consists of a leveling solenoid valve and a gate solenoid valve.
The gate solenoid valve opens and closes the passage between the compressor and the height control cylin-
der (pneumatic cylinder).
DTC No.
DTC Detecting Condition
Trouble Area
C1733/33
Either of the following conditions is detected:
1. With the height control valve inactivated, an open signal of
the height control valve is detected for 1 sec. or more.
2. With the height control valve activated, a short signal of the
valve is detected 8 times successively.
Gate solenoid valve (Height control valve)
Gate solenoid valve (Height control valve) circuit
Suspension control ECU
HINT:
Once the ECU stores DTC C1733/33 in the memory, the vehicle height control is suspended until a
normal signal is input to the ECU from the height control solenoid valves. However, control is resumed
if the ignition switch is turned OFF, then ON again.
Malfunction in the gate solenoid valve:
The height control operation is suspended, and the height control indicator lamp does not change by
operating the height control switch.
WIRING DIAGRAM
DIDDN–01
–
DIAGNOSTICS
AIR SUSPENSION SYSTEM
DI–737
931
INSPECTION PROCEDURE
HINT:
If DTC C1761/61 (ECU malfunction) and/or C1774/74 (power source circuit) is displayed, perform the
inspection necessary for DTC C1761/61 (See page
) and/or C1774/74 (See page
(If DTC C1761/61 and the C1774/74 are output at the same time, perform the inspection necessary
for DTC C1774/74 first.)
Start the inspection from step 1 when using the hand–held tester, and start from step 2 when not using
the hand–held tester.
1
Perform active test using hand–held tester.
PREPARATION:
(a)
Connect the hand–held tester to the DLC3.
(b)
Turn the ignition switch ON, and push the hand–held tester main switch ON.
(c)
Select the item ”GATE SOL REAR” in the ACTIVE TEST, and operate it with the hand–held tester.
AIR SUSPENSION:
Item
Vehicle Condition / Test Details
Diagnostic Note
GATE SOL REAR
Turn gate solenoid valve / ON or OFF
Operation sound of solenoid (clicking sound) can
be heard
CHECK:
(a)
Check whether the solenoid makes sound.
(b)
Check whether the height control valve has continuity (will vibrate).
OK:
The solenoid makes sound, and the height control valve has continuity (will vibrate).
RESULT:
NG
A
OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
B
OK (When troubleshooting according to the DTC chart)
C
B
Proceed to next circuit inspection shown in
problem symptoms table (See page
C
Replace suspension control ECU
(See page
).
A
F19437
Connector Front View:
3 2 1
DI–738
–
DIAGNOSTICS
AIR SUSPENSION SYSTEM
932
2
Inspect gate solenoid valve (height control valve).
PREPARATION:
Disconnect the valve connector.
CHECK:
Measure the resistance between terminals.
OK:
Solenoid valve
Tester connection
Resistance
Gate solenoid valve
1 – 2
17.5 to 21.5
Ω
CHECK:
Check the operating sound of the valves when battery voltage
is applied to the terminals as shown below.
Solenoid valve
Battery positive
Battery negative
Gate solenoid valve
1
2
OK:
Operating sound (clicking) can be heard.
HINT:
When a malfunction is found in the gate solenoid valve, replace
the height control valve.
NG
Replace height control valve
(See page
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст