Toyota Sequoia (2005). Manual — part 953
AC3IB–02
I21380
I21383
AC–74
–
AIR CONDITIONING
REAR A/C EXPANSION VALVE
3801
REAR A/C EXPANSION VALVE
REMOVAL
1.
DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, refer to the following:
Evacuate air from the refrigeration system.
Charge the system with refrigerant and inspect for leak-
age of refrigerant.
Specified amount:
Dual A/C: 1050
±
50 g (37.03
±
1.76 oz.)
2.
DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all coolant.
3.
REMOVE REAR SEAT OUTER BELT FLOOR AN-
CHORS
4.
REMOVE BACKDOOR SCUFF PLATE
5.
REMOVE REAR DOOR SCUFF PLATE RH
6.
REMOVE UPPER BACK DOOR GARNISH
7.
REMOVE REAR WINDOW SIDE GARNISH RH
8.
REMOVE REAR QUARTER TRIM PANEL RH
9.
REMOVE QUARTER PILLAR GARNISH RH
10.
DISCONNECT LIQUID AND SUCTION TUBES
Remove the 2 bolts and disconnect both tubes.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
NOTICE:
Cap the openings immediately to keep moisture or dirt out
of the system.
HINT:
At the time of installation, refer to the following:
Lubricate 2 new O–rings with compressor oil and install them
to the tubes.
11.
REMOVE AIR DUCT
(a)
Remove the 3 clips and cover.
(b)
Remove the 2 air ducts.
(c)
Disconnect the connectors and wire harness clamps.
I21799
I21384
I21387
Nut A:
Nut B:
–
AIR CONDITIONING
REAR A/C EXPANSION VALVE
AC–75
3802
12.
REMOVE EXPANSION VALVE
(a)
Remove the 4 screws and 2 brackets.
(b)
Pry out the packing.
HINT:
At the time of installation, refer to the following:
Do not refuse the packing.
(c)
Using a hexagon wrench (5.0 mm (0.20 in.)), remove the
2 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(d)
Remove the 3 bolts.
(e)
Lift the A/C unit until the tube and accessary can be re-
moved.
(f)
Remove the tube and accessary.
(g)
Remove the holder and disconnect the heat sensing
tube.
(h)
Loosen the 2 nuts and remove the expansion valve.
Torque:
Nut A: 13 N·m (135 kgf·cm, 10 in.·lbf)
Nut B: 22 N·m (235 kgf·cm, 16 in.·lbf)
HINT:
At the time of installation, refer to the following:
Lubricate 2 new O–rings with compressor oil and install them
to the expansion valve.
AC3IC–01
AC–76
–
AIR CONDITIONING
REAR A/C EXPANSION VALVE
3803
INSPECTION
INSPECT EVAPORATOR
(a)
Check evaporator fins for blockage.
If the fins are clogged, clean them with compressor air.
NOTICE:
Never use water to clean the evaporator.
(b)
Check fitting for cracks or scratches.
If necessary, repair or replace.
AC3ID–01
–
AIR CONDITIONING
REAR A/C EXPANSION VALVE
AC–77
3804
INSTALLATION
Installation is in the reverse order of removal (See page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст