Toyota Sequoia (2005). Manual — part 895
BO45O–01
BO–16
–
BODY
FRONT DOOR
3569
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page
).
BO45P–01
H16670
Rear Door
Quarter Window Glass
Upper Window Frame Moulding
Door Glass Run
Division Bar
Rear Door Weatherstrip
Door Glass
Quarter Window
Weatherstrip
Door Lock Striker
Outside Handle
Door Lock Outer Cover
Window Regulator Motor
No. 2 Rear Door
Weatherstrip
Door Hinge
Child Protection Cover
Door Lock
Cable Protection
Door Belt Moulding
Inner Weatherstrip
Door Trim
Courtesy Light
Inside Handle Bezel
Speaker
Upper Armrest Base Panel
Power Window Switch
Service Hole Cover
Inside Handle
Ash Tray
Window Regulator
Sub–assembly
Door Hinge
Door Check
Precoated part
: Specified torque
N·m (kgf·cm, ft·lbf)
23 (230, 17)
23 (230, 17)
23 (230, 17)
23 (230, 17)
23 (230, 17)
30 (306, 22)
5.5 (56, 49 in.·lbf)
5.5 (56, 49 in.·lbf)
8.0 (82, 71 in.·lbf)
5.0 (51, 44 in.·lbf)
5.5 (56, 49 in.·lbf)
–
BODY
REAR DOOR
BO–17
3570
REAR DOOR
COMPONENTS
BO45Q–01
H04751
H16659
H16660
8 Clips
BO–18
–
BODY
REAR DOOR
3571
DISASSEMBLY
1.
REMOVE INSIDE HANDLE BEZEL
(a)
Using a screwdriver, open the cover.
HINT:
Tape the screwdriver tip before use.
(b)
Remove the screw.
(c)
Using a screwdriver, remove the inside handle bezel as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
2.
REMOVE COURTESY LIGHT
3.
REMOVE UPPER ARMREST BASE PANEL WITH
POWER WINDOW SWITCH
(a)
Remove the ash tray.
(b)
Using a screwdriver, remove the upper armrest base pan-
el with power window switch.
(c)
Disconnect the connector.
(d)
Remove the power window switch from the upper armrest
base panel.
4.
REMOVE DOOR TRIM
(a)
Using a screwdriver, remove the cap.
HINT:
Tape the screwdriver tip before use.
(b)
Remove the screw and 2 clips.
(c)
Insert a screwdriver between the door trim and door panel
to pry the door trim.
HINT:
Tape the screwdriver tip before use.
(d)
Pull the door trim upward to remove the door trim.
(e)
Remove the inner weatherstrip from the door trim.
5.
REMOVE SPEAKER
H16644
H16643
H05546
–
BODY
REAR DOOR
BO–19
3572
6.
REMOVE INSIDE HANDLE
(a)
Slide the inside handle backward to remove it.
(b)
Disconnect the 2 cables from inside handle as shown in
the illustration.
7.
REMOVE SERVICE HOLE COVER
(a)
Using a clip remover, remove the clamp and grommets.
(b)
Remove the service hole cover.
NOTICE:
Do not tear the cover.
HINT:
At the time of reassembly, please refer to the following item.
Bring out the 2 control cables and wire harness through the ser-
vice hole cover.
8.
REMOVE DIVISION BAR
HINT:
Insert a shop rag inside the door panel to prevent scratching the
glass.
(a)
Open the door glass until the bolts appear in the service
hole.
(b)
Remove the 2 door glass set nuts.
(c)
Remove the door glass from the glass bracket and lower
the door glass into the door panel.
NOTICE:
Do not damage the door glass.
HINT:
Position the door glass toward the front as much as possible.
(d)
Remove the door glass run.
(e)
Remove the 2 bolts and screw.
(f)
Pull the division bar forward.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст