Toyota Sequoia (2005). Manual — part 379

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

DI–1311

1505

2

Perform sensitivity check.

Using the hand–held tester, perform ”Sensitivity check” (see page

DI–1147

).

OK:

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

NG

Go to step 4.

OK

3

Check DTC.

CHECK:
(a)

Turn the ignition switch to the ON position.

(b)

Clear the DTCs stored in memory (see page

DI–1147

).

HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c)

Turn the ignition switch to the LOCK position.

(d)

Turn the ignition switch to the ON position.

(e)

Using the hand–held tester, check the DTCs of the occupant classification ECU (see page

DI–1147

).

OK:

DTC B1787 is not output.

HINT:
Codes other than DTC B1787 may be output at this time, but they are not related to this check.

NG

Go to step 4.

OK

END

DI–1312

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

1506

4

Replace front seat assembly RH.

(a)

Turn the ignition switch to the LOCK position.

(b)

Disconnect the negative (–) terminal cable from the battery, and wait for at least 90 seconds.

(c)

Replace the front seat assembly RH (see page

BO–112

,

BO–126

).

HINT:
Perform the inspection using parts from a normal vehicle if possible.

NEXT

5

Perform zero point calibration.

(a)

Connect the negative (–) terminal cable to the battery.

(b)

Connect the hand–held tester to the DLC3.

(c)

Turn the ignition switch to the ON position.

(d)

Using the hand–held tester, perform ”Zero point calibration” (see page

DI–1128

).

OK:

The ”COMPLETED” is displayed.

NG

Go to step 8.

OK

6

Perform sensitivity check.

Using the hand–held tester, perform ”Sensitivity check” (see page

DI–1128

).

OK:

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

NG

Go to step 8.

OK

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

DI–1313

1507

7

Check DTC.

CHECK:
(a)

Turn the ignition switch to the ON position.

(b)

Clear the DTCs stored in memory (see page

DI–1147

).

HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c)

Turn the ignition switch to the LOCK position.

(d)

Turn the ignition switch to the ON position.

(e)

Using the hand–held tester, check the DTCs of the occupant classification ECU (see page

DI–1147

).

OK:

DTC B1787 is not output.

HINT:
Codes other than DTC B1787 may be output at this time, but they are not related to this check.

NG

Go to step 8.

OK

END

DI–1314

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

1508

8

Replace occupant classification ECU.

(a)

Turn the ignition switch to the LOCK position.

(b)

Disconnect the negative (–) terminal cable from the battery, and wait for at least 90 seconds.

(c)

Replace the occupant classification ECU (see page

RS–111

).

NEXT

9

Perform zero point calibration.

(a)

Connect the negative (–) terminal cable to the battery.

(b)

Connect the hand–held tester to the DLC3.

(c)

Turn the ignition switch to the ON position.

(d)

Using the hand–held tester, perform ”Zero point calibration” (see page

DI–1128

).

OK:

The ”COMPLETED” is displayed.

NEXT

10

Perform sensitivity check.

Using the hand–held tester, perform ”Sensitivity check” (see page

DI–1128

).

OK:

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

NEXT

END