Toyota Sequoia (2005). Manual — part 918
BO46X–01
BO–108
–
BODY
ROOF HEADLINING
3661
INSTALLATION
Installation is in the reverse order of removal (See page
BO46Y–01
H16753
Side Door Step
Plate Cover
Step Cover
Protector
Step Plate
Side Step Bracket
No. 3 Side Step Bracket
No. 2 Side Step Bracket
No. 1 Side Step Bracket
Step Cover
Protector
N·m (kgf·cm, ft·lbf)
: Specified torque
19 (195, 14)
19 (195, 14)
19 (195, 14)
19 (195, 14)
4.9 (50, 43 in.·lbf)
4.9 (50, 43 in.·lbf)
4.9 (50, 43 in.·lbf)
4.9 (50, 43 in.·lbf)
–
BODY
SIDE STEP
BO–109
3662
SIDE STEP
COMPONENTS
BO4S6–01
H24329
37 (380, 27)
37 (380, 27)
37 (380, 27)
37 (380, 27)
37 (380, 27)
42 (430, 32)
Seatback Cover
Seat Cushion
Cover
Seat Cushion
Pad
Armrest Cap
Armrest Spacer
Armrest
Lock Plate
Spacer
Armrest
Assembly
Headrest
Headrest Support
Seatback Pad
Lumbar Support
Adjuster
Seat Frame Assembly
Seat Position Sensor
Protector
Seat Position
Sensor
Seat Cushion
Inner Shield
Seat Cushion
Lower Shield
Front Seat Inner Belt
RH Reclining
Adjuster Inside
Cover
RH Seatback
Shield
Vertical Adjuster
Bracket Inner Cover
Vertical Adjuster
Bracket Outer Cover
LH Reclining
Adjuster Inside Cover
Reclining Knob
Slide Knob
Seat Cushion Outer Shield
Lumbar Switch
Power Seat Switch
LH Seatback Shield
Hog Ring
Seat Track
Cover
Seat Track
Cover
Bushing
Hog Ring
Non–reusable part
: Specified torque
N·m (kgf·cm, ft·lbf)
w/ Side airbag:
5.5 (56, 49 in.·lbf)
w/ Seat heater:
w/ Seat heater:
Seat Cushion Heater Assembly
Seatback
Heater Assembly
Occupant Classification ECU
Passenger’s seat:
Driver’s seat:
Driver’s seat:
BO–110
–
BODY
FRONT SEAT (Power Adjuster Type)
3663
FRONT SEAT (Power Adjuster Type)
COMPONENTS
HINT:
The procedures listed below are for the LH side.
BO4S7–01
–
BODY
FRONT SEAT (Power Adjuster Type)
BO–111
3664
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (–) terminal cable is disconnected from the battery.
(The SRS is equipped with a back–up power source. If work is started within 90 seconds from discon-
necting the negative (–) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page
HINT:
The procedures listed below are for the LH side.
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2.
REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3.
REMOVE FRONT SEAT
(a)
Remove the 4 bolts.
(b)
Disconnect the connectors.
(c)
w/ Side airbag:
Disconnect the airbag connector.
(d)
Remove the front seat.
NOTICE:
Be careful not to damage the body.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст