Toyota Sequoia (2005). Manual — part 357
C91384
H01010
G27652
H23572
Airbag
Sensor
Assembly
A19
A
B
C
D
LBE+
LBE–
Front Seat
Inner Belt LH
Floor Wire No. 2
C91384
H01010
G27652
H23572
Airbag
Sensor
Assembly
A19
A
B
C
D
LBE+
LBE–
Front Seat
Inner Belt LH
Floor Wire No. 2
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–1223
1417
4
Check floor wire No. 2 (short).
PREPARATION:
Disconnect the service wire from connector ”C”.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
A19–10 (LBE+) –
A19–18 (LBE–)
Always
1 M
Ω
or higher
NG
Repair or replace floor wire No. 2.
OK
5
Check floor wire No. 2 (short to B+).
PREPARATION:
Connect the negative (–) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a)
Turn the ignition switch to the ON position.
(b)
Measure the voltage according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
A19–10 (LBE+) –
Body ground
Ignition switch ON
Below 1 V
A19–18 (LBE–) –
Body ground
Ignition switch ON
Below 1 V
NG
Repair or replace floor wire No. 2.
OK
C91384
H01010
G27652
H23572
Airbag
Sensor
Assembly
A19
A
B
C
D
LBE+
LBE–
Front Seat
Inner Belt LH
Floor Wire No. 2
DI–1224
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
1418
6
Check floor wire No. 2 (short to ground).
PREPARATION:
(a)
Turn the ignition switch to the LOCK position.
(b)
Disconnect the negative (–) terminal cable from the bat-
tery, and wait for at least 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester Connection
Condition
Specified Condition
A19–10 (LBE+) –
Body ground
Always
1 M
Ω
or higher
A19–18 (LBE–) –
Body ground
Always
1 M
Ω
or higher
NG
Repair or replace floor wire No. 2.
OK
C84216
H10600 C92968
H24657
CG
TC
DTC B1656/38
DLC3
Airbag
Sensor
Assembly
Front Seat
Inner Belt LH
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–1225
1419
7
Check front seat inner belt LH.
PREPARATION:
(a)
Connect the connectors to the airbag sensor assembly
and the front seat inner belt LH.
(b)
Connect the negative (–) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a)
Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b)
Clear the DTCs stored in memory (see page
(c)
Turn the ignition switch to the LOCK position.
(d)
Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e)
OK:
DTC B1656/38 is not output.
HINT:
Codes other than DTC B1656/38 may be output at this time, but
they are not related to this check.
NG
Go to step 8.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page
8
Replace front seat inner belt LH.
(a)
Turn the ignition switch to the LOCK position.
(b)
Disconnect the negative (–) terminal cable from the battery, and wait for at least 90 seconds.
(c)
Replace the front seat inner belt LH (see page
,
HINT:
Perform inspection using parts from a normal vehicle if possible.
NEXT
C84216
H10600 C92968
H24657
CG
TC
DTC B1656/38
DLC3
Airbag
Sensor
Assembly
Front Seat
Inner Belt LH
DI–1226
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
1420
9
Check airbag sensor assembly.
PREPARATION:
Connect the negative (–) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a)
Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b)
Clear the DTCs stored in memory (see page
(c)
Turn the ignition switch to the LOCK position.
(d)
Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e)
OK:
DTC B1656/38 is not output.
HINT:
Codes other than DTC B1656/38 may be output at this time, but
they are not related to this check.
NG
Replace airbag sensor assembly
(see page
).
OK
END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст