Toyota Sequoia (2005). Manual — part 651
A23302
RH No.3 Timing Belt Cover
No.2 Timing
Belt Cover
LH No.3 Timing Belt Cover
Drive Belt Idler Pulley
Camshaft Position
Sensor Connector
Cover Plate
Oil Cooler Pipe
Engine Wire
7.5 (76, 66 in.·lbf)
16 (160, 12)
7.5 (76, 66 in.·lbf)
N·m (kgf·cm, ft·lbf) : Specified torque
Wire Grommet
39 (400, 29)
A23303
Timing Belt
LH Camshaft Timing Pulley
Timing Belt Tensioner
Dust Boot
245 (2,500, 181)
16 (160, 12)
32 (330, 24)
RH Camshaft Timing Pulley
26 (270, 19)
Fan Bracket
N·m (kgf·cm, ft·lbf) : Specified torque
8.1 (83, 72 in.·lbf)
EM–14
–
ENGINE MECHANICAL
TIMING BELT
2593
A23304
Generator Wire
Drive Belt Tensioner
No.1 Timing Belt Cover
Generator
Crankshaft Pulley
39 (400, 29)
No.1 Idler Pulley
Timing Belt
Plate Washer
Crankshaft Timing Pulley
Timing Belt Cover Spacer
No.2 Idler Pulley
Timing Belt Guide
(Crankshaft Angle Sensor Plate)
Gasket
34.5 (350, 25)
34.5 (350, 25)
N·m (kgf·cm, ft·lbf) : Specified torque
Precoated part
26 (265, 19)
39 (400, 29)
15.5 (158, 11)
–
ENGINE MECHANICAL
TIMING BELT
EM–15
2594
EM1WX–01
A08934
A04329
A04331
EM–16
–
ENGINE MECHANICAL
TIMING BELT
2595
REMOVAL
1.
REMOVE ENGINE UNDER COVER
2.
DRAIN ENGINE COOLANT
3.
REMOVE RADIATOR ASSEMBLY (See page
4.
REMOVE THROTTLE BODY COVER
5.
REMOVE INTAKE AIR CONNECTOR ASSEMBLY
6.
REMOVE DRIVE BELT, FAN, FLUID COUPLING AND
FAN PULLEY
(a)
Loosen the 4 nuts holding the fluid coupling to the fan
bracket.
(b)
Remove the drive belt. (See page
(c)
Remove the 4 nuts, the fan, fluid coupling assembly and
fan pulley.
7.
DISCONNECT PS PUMP
Remove the 3 bolts, and disconnect the PS pump from the en-
gine.
HINT:
Suspend the PS pump securely.
8.
REMOVE DRIVE BELT IDLER PULLEY
Remove the pulley bolt, cover plate and idler pulley.
9.
REMOVE RH NO.3 TIMING BELT COVER
Remove the 3 bolts, nut and RH No.3 timing belt cover.
10.
REMOVE LH NO.3 TIMING BELT COVER
(a)
Disconnect the engine wire from the 2 wire clamps.
(b)
Remove the 4 bolts and nut.
(c)
Disconnect the camshaft position sensor wire from the
wire clamp on the LH No.3 timing belt cover.
(d)
Disconnect the camshaft position sensor connector from
the connector bracket.
(e)
Disconnect the camshaft position sensor connector.
(f)
Remove the wire grommet from the LH No.3 timing belt
cover.
A04330
A04455
A23305
A23306
SST
–
ENGINE MECHANICAL
TIMING BELT
EM–17
2596
(g)
Remove the LH No.3 timing belt cover.
(h)
Remove the bolt, nut and oil cooler pipe.
11.
REMOVE NO.2 TIMING BELT COVER
Remove the 2 bolts and No.2 timing belt cover.
12.
DISCONNECT A/C COMPRESSOR FROM ENGINE
(See page
13.
REMOVE FAN BRACKET
Remove the 2 bolts, 2 nuts and fan bracket.
14.
IF RE–USING TIMING BELT, CHECK INSTALLATION
MARKS ON TIMING BELT
Check that there are 3 installation marks on the timing belt by
turning the crankshaft pulley as shown in the illustration.
HINT:
If the installation marks have disappeared, place a new installa-
tion mark on the timing belt before removing each part.
15.
LOOSEN CRANKSHAFT PULLEY BOLT
Using SST, loosen the pulley bolt.
SST
09213–70011 (90105–08076), 09330–00021
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст