Toyota Sequoia (2005). Manual — part 373

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

DI–1287

1481

8

Replace occupant classification ECU.

(a)

Turn the ignition switch to the LOCK position.

(b)

Disconnect the negative (–) terminal cable from the battery, and wait for at least 90 seconds.

(c)

Replace the occupant classification ECU (see page

RS–111

).

HINT:
Perform the inspection using parts from a normal vehicle if possible.

NEXT

9

Perform zero point calibration.

(a)

Connect the negative (–) terminal cable to the battery.

(b)

Connect the hand–held tester to the DLC3.

(c)

Turn the ignition switch to the ON position.

(d)

Using the hand–held tester, perform ”Zero point calibration” (see page

DI–1128

).

OK:

The ”COMPLETED” is displayed.

NG

Go to step 12.

OK

10

Perform sensitivity check.

Using the hand–held tester, perform ”Sensitivity check” (see page

DI–1128

).

OK:

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

NG

Go to step 12.

OK

DI–1288

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

1482

11

Check DTC.

CHECK:
(a)

Turn the ignition switch to the ON position.

(b)

Clear the DTCs stored in memory (see page

DI–1147

).

HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c)

Turn the ignition switch to the LOCK position.

(d)

Turn the ignition switch to the ON position.

(e)

Using the hand–held tester, check the DTCs of the occupant classification ECU (see page

DI–1147

).

OK:

DTC B1782 is not output.

HINT:
Codes other than DTC B1782 may be output at this time, but they are not related to this check.

NG

Go to step 12.

OK

END

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

DI–1289

1483

12

Replace front seat assembly RH.

(a)

Turn the ignition switch to the LOCK position.

(b)

Disconnect the negative (–) terminal cable from the battery, and wait for at least 90 seconds.

(c)

Replace the front seat assembly RH (see page

BO–112

,

BO–126

).

NEXT

13

Perform zero point calibration.

(a)

Connect the negative (–) terminal cable to the battery.

(b)

Connect the hand–held tester to the DLC3.

(c)

Turn the ignition switch to the ON position.

(d)

Using the hand–held tester, perform ”Zero point calibration” (see page

DI–1128

).

OK:

The ”COMPLETED” is displayed.

NEXT

14

Perform sensitivity check.

Using the hand–held tester, perform ”Sensitivity check” (see page

DI–1128

).

OK:

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

NEXT

END

DI–1290

–

DIAGNOSTICS

SUPPLEMENTAL RESTRAINT SYSTEM

1484

DTC

B1783

Occupant Classification Sensor Rear RH
Circuit Malfunction

CIRCUIT DESCRIPTION

The occupant classification sensor rear RH circuit consists of the occupant classification ECU and the occu-
pant classification sensor rear RH.
DTC B1783 is recorded when a malfunction is detected in the occupant classification sensor rear RH circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1783

The occupant classification ECU receives a line short

circuit signal, an open circuit signal, a short circuit to

ground signal or a short circuit to B+ signal in the occu-

pant classification sensor rear RH circuit for 2 seconds.

Occupant classification sensor rear RH malfunction

Occupant classification ECU malfunction

Front seat assembly RH

(Occupant classification sensor rear RH)

Occupant classification ECU

Seat wire No. 1

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the supplemental restraint system, check
the DTCs stored in the occupant classification ECU. When DTC B1783 is output, perform troubleshooting
for the DTC.

DIDH8–01