Toyota Sequoia (2005). Manual — part 763
SA2348
SST
Z00641
SST
W04006
R02482
SST
R13226
–
SUSPENSION AND AXLE
FRONT DIFFERENTIAL CARRIER
SA–45
3041
11.
REMOVE OIL SEAL AND OIL SLINGER
(a)
Using SST, remove the oil seal.
SST
09308–10010
(b)
Remove the oil slinger.
12.
REMOVE REAR BEARING AND BEARING SPACER
(a)
Using SST, remove the rear bearing from the drive pinion.
SST
09556–22010
(b)
Remove the bearing spacer.
13.
REMOVE SIDE BEARING RETAINER
Remove the 10 bolts and tap out the retainer with a plastic ham-
mer.
14.
REMOVE DIFFERENTIAL CASE ASSEMBLY
15.
REMOVE DRIVE PINION FROM DIFFERENTIAL CAR-
RIER
16.
REMOVE DRIVE PINION FRONT BEARING
Using SST and a press, remove the bearing and washer from
the drive pinion.
SST
09950–00020
HINT:
If the drive pinion or ring gear is damaged, replace them as a
set.
17.
REMOVE DRIVE PINION BEARING OUTER RACES
(a)
Using a brass bar and hammer, remove the front bearing
outer race.
R13210
SST
R13211
F14774
SST
SST
R13213
SST
SST
FA1998
Matchmarks
R11392
SST
SST
SA–46
–
SUSPENSION AND AXLE
FRONT DIFFERENTIAL CARRIER
3042
(b)
Using SST, remove the rear bearing outer race.
SST
09502–12010, 09612–65014 (09612–01020,
09612–01050)
18.
REMOVE SIDE BEARING OUTER RACES
HINT:
Measure the plate washer thickness and note it down.
Tag the bearing outer races to show the location for reas-
sembling.
(a)
Using SST and a press, remove the plate washer and out-
er race from the bearing retainer.
SST
09950–60010 (09951–00650),
09950–70010 (09951–07150)
(b)
Using SST and a press, remove the plate washer and out-
er race from the differential carrier.
SST
09950–60010 (09951–00650),
09950–70010 (09951–07150)
19.
REMOVE RING GEAR
(a)
Place matchmarks on the ring gear and differential case.
(b)
Using a screwdriver and hammer, unstake the 5 lock
plates.
(c)
Remove the 10 bolts and 5 lock plates.
(d)
Using a plastic hammer, tap on the ring gear to separate
it from the differential case.
20.
REMOVE SIDE BEARINGS
Using SST, remove the 2 side bearings from the differential
case.
SST
09950–40011 (09951–04010, 09952–04010,
09953–04020, 09954–04010, 09955–04061,
09957–04010, 09958–04011),
09950–60010 (09951–00480)
HINT:
Fix the claws of SST to the notch in the differential case.
RA0997
SA0353
–
SUSPENSION AND AXLE
FRONT DIFFERENTIAL CARRIER
SA–47
3043
21.
DISASSEMBLE DIFFERENTIAL CASE ASSEMBLY
(a)
Using a pin punch and hammer, remove the straight pin.
(b)
Remove the pinion shaft, 2 pinion gears, pinion gear
thrust washers, side gears and side gear thrust washers
from the differential case.
22.
REMOVE BEARINGS
Using a brass bar and hammer, remove the 2 bearings.
SA24R–02
R04465
SST
Socket Wrench
R04348
SST
Z03857
R13199
SST
R13422
SA–48
–
SUSPENSION AND AXLE
FRONT DIFFERENTIAL CARRIER
3044
REPLACEMENT
1.
REPLACE COMPANION FLANGE DUST DEFLECTOR,
IF NECESSARY
(a)
Using SST, a socket wrench and a press, remove the dust
deflector.
SST
09950–00020
(b)
Using SST and a press, install a new dust deflector.
SST
09636–20010
2.
REPLACE INTERMEDIATE SHAFT NO. 2, IF NEC-
ESSARY
(a)
Remove the clutch hub.
(1)
Using a snap ring expander, remove the snap ring.
(2)
Remove the clutch hub from the intermediate shaft
No. 2.
(b)
Remove the oil seal.
Using SST, remove the oil seal from the tube.
SST
09308–00010
(c)
Remove the intermediate shaft No. 2 from the tube.
(1)
Using needle nose pliers, remove the snap ring.
(2)
Remove the shaft from the tube.
(d)
Remove the intermediate shaft No. 2 bearing.
(1)
Using a snap ring expander, remove the snap ring.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст