Toyota Sequoia (2005). Manual — part 843
H23931
RS–78
–
SUPPLEMENTAL RESTRAINT SYSTEM
CURTAIN SHIELD AIRBAG ASSEMBLY
3361
(3)
Press the SST activation switch and deploy the air-
bag.
CAUTION:
When deploying the airbag, make sure that no one is near
the tire.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
(i)
Dispose of the curtain shield airbag assembly.
CAUTION:
The curtain shield airbag assembly becomes ex-
tremely hot when the airbag is deployed, so do not
touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a cur-
tain shield airbag assembly with a deployed airbag.
Do not apply water, etc. to a curtain shield airbag as-
sembly with a deployed airbag.
Always wash your hands with water after completing
the operation.
(1)
Remove the curtain shield airbag assembly from
the tire.
(2)
Place the curtain shield airbag assembly in a plastic
bag, tie it tightly and dispose of it as other general
part disposal.
RS0N6–10
–
SUPPLEMENTAL RESTRAINT SYSTEM
CURTAIN SHIELD AIRBAG ASSEMBLY
RS–79
3362
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the curtain shield airbag assembly or curtain shield airbag cover with a new
one.
Case
Replacing part
The curtain shield airbag has been deployed.
Curtain shield airbag assembly
The curtain shield airbag assembly has been found to be faulty in trouble-
shooting.
Curtain shield airbag assembly
The curtain shield airbag assembly has been found to be faulty while check-
ing items
(See page
Curtain shield airbag assembly
The front pillar garnish has been found to be faulty while checking items
(See page
Front pillar garnish
The roof headlining has been found to be faulty while checking items
(See page
Roof headlining
The curtain shield airbag assembly has been dropped.
Curtain shield airbag assembly
CAUTION:
For removal and installation of the curtain shield airbag assembly, see page
and
sure to follow the correct procedure.
RS0TH–07
H23897
RS–80
–
SUPPLEMENTAL RESTRAINT SYSTEM
CURTAIN SHIELD AIRBAG ASSEMBLY
3363
INSTALLATION
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1.
INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a)
Install the curtain shield airbag assembly with the 13
bolts.
Torque: 9.8 N·m (100 kgf·cm, 7 ft·lbf)
CAUTION:
Pay attention not to twist the deployment section of the cur-
tain shield airbag assembly.
NOTICE:
If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.
When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
(b)
Connect the connector of the curtain shield airbag as-
sembly.
2.
INSTALL ROOF HEADLINING (SEE PAGE
3.
CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
4.
PERFORM INITIALIZATION (SEE PAGE
Some system need initialization when disconnecting the cable
from the negative battery terminal.
5.
RS0BK–11
H24668
N·m (kgf·cm, ft·lbf) : Specified torque
Airbag Sensor Assembly
Front Console Box
Rear Console Box
Upper Console Panel
17.5 (179, 13)
Console Cover Rear
Shifting Hole Cover
Rear Console Box
Disc Player
w/ Rear seat audio or Rear seat entertainment:
17.5 (179, 13)
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
RS–81
3364
AIRBAG SENSOR ASSEMBLY
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст