Toyota Sequoia (2005). Manual — part 834
RS0BI–07
RS–42
–
SUPPLEMENTAL RESTRAINT SYSTEM
FRONT PASSENGER AIRBAG ASSEMBLY
3325
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the front passenger airbag assembly, instrument panel or instrument panel
reinforcement with a new one.
Case
Replacing part
The airbag has been deployed.
Front passenger airbag assembly
The front passenger airbag assembly has been found to be faulty in trouble-
shooting.
Front passenger airbag assembly
The front passenger airbag assembly has been found to be faulty while
checking items
(see page
Front passenger airbag assembly
The instrument panel has been found to be faulty while checking items
(see page
Instrument panel
The instrument panel reinforcement has been found to be faulty while check-
ing items
(see page
Instrument panel reinforcement
The front passenger airbag assembly has been dropped.
Front passenger airbag assembly
CAUTION:
For replacement of the front passenger airbag assembly, see page
, Be sure to fol-
low the correct procedure.
RS0T8–03
H23212
–
SUPPLEMENTAL RESTRAINT SYSTEM
FRONT PASSENGER AIRBAG ASSEMBLY
RS–43
3326
INSTALLATION
NOTICE:
If the front passenger airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the front passenger
airbag assembly with a new one.
When installing the front passenger airbag assembly,
take care it is not pinched between other parts.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1.
INSTALL FRONT PASSENGER AIRBAG ASSEMBLY
(a)
Install the bolt to hold the front passenger airbag assem-
bly and instrument panel reinforcement.
Torque: 20 N·m (204 kgf·cm, 15 ft·lbf)
(b)
Install the 2 bolts to hold the front passenger airbag as-
sembly and instrument panel.
Torque: 5.0 N·m (51 kgf·cm, 44 in.·lbf)
2.
INSTALL LOWER INSTRUMENT COVER
(SEE PAGE
3.
INSTALL FRONT CONSOLE BOX
(SEE PAGE
4.
INSTALL REAR CONSOLE BOX
(SEE PAGE
5.
INSTALL UPPER CONSOLE PANEL
(SEE PAGE
6.
INSTALL SHIFTING HOLE COVER
(SEE PAGE
7.
INSTALL LOWER NO. 2 FINISH PANEL
(SEE PAGE
8.
INSTALL GLOVE COMPARTMENT DOOR
(SEE PAGE
9.
INSTALL LOWER FINISH PANEL
(SEE PAGE
10.
INSTALL SIDE PANELS (SEE PAGE
)
H23211
RS–44
–
SUPPLEMENTAL RESTRAINT SYSTEM
FRONT PASSENGER AIRBAG ASSEMBLY
3327
11.
CONNECT AIRBAG CONNECTOR
(a)
Connect the airbag connector as shown in the illustration.
(b)
Attach the connector clamp to the reinforcement.
12.
INSTALL COWL TRIM BOARDS
(SEE PAGE
13.
INSTALL FRONT DOOR SCUFF PLATES
(SEE PAGE
14.
CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
15.
PERFORM INITIALIZATION (SEE PAGE
Some system need initialization when disconnecting the cable
from the negative battery terminal.
16.
RS0T9–06
H23932
37 (377, 27)
37 (377, 27)
37 (377, 27)
37 (377, 27)
37 (377, 27)
42 (428, 31)
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
Seat Cushion Outer Shield
Slide Knob
Reclining Knob
Lumbar Switch
Power Seat Switch
Seat Cushion Lower Shield
Seat Position Sensor
Seat Cushion Inner Shield
Driver’s seat:
Torx
Screw
Seat Position
Sensor Protector
Driver’s seat:
Hog Ring
Front Seat Inner Belt
Headrest Support
Seat Frame Assembly
Seatback Cover
Seatback Pad
Spacer
Seat Track Cover
Seat Track Cover
Armrest Assembly
Armrest Cap
Armrest Spacer
Armrest Lock Plate
Headrest
8.0 (82, 72 in.·lbf)
w/ Side Airbag:
5.5 (56, 49 in.·lbf)
–
SUPPLEMENTAL RESTRAINT SYSTEM
SIDE AIRBAG ASSEMBLY (Power Adjuster Type)
RS–45
3328
SIDE AIRBAG ASSEMBLY (Power Adjuster Type)
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст