Toyota Sequoia (2005). Manual — part 757
SA143–10
F14316
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
64 (650, 47)
Brake Caliper
Hub Bolt
Cotter Pin
105 (1,100, 77)
8.0 (82, 71 in.·lbf)
Speed Sensor
Shock Absorber
135 (1,400, 100)
65 (663, 48)
123 (1,250, 90)
28 (285, 21)
Steering Knuckle with Axle Hub
Disc
4WD:
Cotter Pin
235 (2,400, 173)
Lock Cap
Grease Cap
Grease Cap
2WD:
4WD:
Oil Seal
Speed Sensor
Rotor
Dust Cover
Steering Knuckle
18 (185, 13)
Oil Seal
Bearing
Snap Ring
Axle Hub
Bearing Spacer
4WD:
274 (2,800, 203)
Lock Nut
2WD:
–
SUSPENSION AND AXLE
FRONT AXLE HUB
SA–21
3017
FRONT AXLE HUB
COMPONENTS
SA23I–04
R13426
F07263
F07264
F07265
SA–22
–
SUSPENSION AND AXLE
FRONT AXLE HUB
3018
REMOVAL
1.
REMOVE FRONT WHEEL
2.
REMOVE GREASE CAP
Using a screwdriver and hammer, remove the grease cap.
3.
4WD:
DISCONNECT DRIVE SHAFT
(a)
Remove the cotter pin and lock cap.
(b)
While applying the brakes, remove the lock nut.
4.
DISCONNECT SPEED SENSOR AND WIRE HARNESS
CLAMP FROM STEERING KNUCKLE
Remove the 2 bolts and disconnect the speed sensor and wire
harness clamp from the steering knuckle.
5.
REMOVE BRAKE CALIPER AND DISC
(a)
Remove the bolt and brake line clamp from the steering
knuckle.
(b)
Remove the 2 bolts, brake caliper and disc.
NOTICE:
Do not damage the brake tube.
(c)
Support the brake caliper securely.
6.
REMOVE SHOCK ABSORBER (See page
7.
DISCONNECT LOWER BALL JOINT
Remove the 4 bolts and disconnect the lower ball joint.
8.
REMOVE STEERING KNUCKLE
(a)
Remove the cotter pin and loosen the nut.
R13196
SST
–
SUSPENSION AND AXLE
FRONT AXLE HUB
SA–23
3019
(b)
Using SST, disconnect the steering knuckle.
SST
09950–40011 (09951–04010, 09952–04010,
09553–04020, 09554–04010, 09955–04031,
09958–04011)
(c)
Remove the nut and steering knuckle.
NOTICE:
4WD:
Be careful not to damage the oil seal and drive shaft boot.
HINT:
4WD:
When it is difficult to disconnect the drive shaft, tap the tip of the
drive shaft with a plastic hammer.
SA145–08
R13215
SST
R13275
SST
SST
SA–24
–
SUSPENSION AND AXLE
FRONT AXLE HUB
3020
DISASSEMBLY
1.
2WD:
REMOVE GREASE CAP
(a)
Mount the axle hub in a soft jaw vise.
HINT:
Close the vise until it holds hub bolts. Do not tighten further.
(b)
Using a screwdriver, remove the grease cap.
2.
4WD:
REMOVE OIL SEAL (INSIDE)
(a)
Mount the axle hub in a soft jaw vise.
HINT:
Close the vise until it holds hub bolts. Do not tighten further.
(b)
Using a screwdriver, remove the oil seal (inside).
3.
2WD:
REMOVE LOCK NUT AND SPEED SENSOR ROTOR
(a)
Using a chisel and hammer, loosen the staked part of the
lock nut.
NOTICE:
Be careful not to damage the bushing.
(b)
Using SST, remove the lock nut.
SST
09318–12010
(c)
Remove the speed sensor rotor.
NOTICE:
Take care not to scratch the serration of the speed sensor
rotor.
4.
REMOVE AXLE HUB FROM STEERING KNUCKLE
(a)
Remove the 4 bolts and shift the dust cover towards the
hub side (outside).
(b)
Using SST, remove the axle hub from the steering
knuckle.
SST
09710–30021 (09710–03051),
09950–40011 (09951–04020, 09952–04010,
09953–04020, 09954–04010, 09955–04031,
09957–04010, 09958–04011)
(c)
Remove the dust cover from the steering knuckle.
(d)
4WD:
Remove the bearing spacer and speed sensor rotor.
NOTICE:
Take care not to scratch the serration of the speed sensor
rotor.
5.
REMOVE OIL SEAL (OUTSIDE)
Using a screwdriver, remove the oil seal (outside) from the
steering knuckle.
6.
REMOVE BEARING FROM STEERING KNUCKLE
(a)
Using snap ring pliers, remove the snap ring.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст