Toyota Sequoia (2005). Manual — part 183
D13657
Add automatic transmission fluid
removing or installing the oil pan (including the oil drain)
removing the transmission valve body assy
removing the torque converter assy, etc.
Start from [*1]
In step (15)
When ATF overflows
When ATF does not
overflow
Go to [*2]
Go to [*3]
END
disconnecting the oil cooler tube
repairing oil leaks, etc.
Start from [*4]
In step (8)
When ATF overflows
When ATF does not
overflow
Go to [*5]
Go to [*6]
Maximum amount of fluid
should be added when:
Minimum amount of fluid
should be added when:
–
DIAGNOSTICS
AUTOMATIC TRANSMISSION
DI–527
721
6.
ADD AUTOMATIC TRANSMISSION FLUID
D14137
Refill Plug
Overflow Plug
D14138
DI–528
–
DIAGNOSTICS
AUTOMATIC TRANSMISSION
722
(a)
When adding maximum amount of fluid: [*1]
(1)
Lift up the vehicle while keeping it level.
(2)
Remove the refill plug and overflow plug.
(3)
Add ATF through the refill hole until it drains out from
the overflow hole.
NOTICE:
Be sure to add Toyota genuine ATF WS.
D14139
Overflow Plug
D14140
Refill Plug
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
D13649
DLC3:
CG
TC
–
DIAGNOSTICS
AUTOMATIC TRANSMISSION
DI–529
723
(4)
Temporarily install the gasket and overflow plug.
Torque: 20 N
⋅
m (204 kgf
⋅
cm, 15 ft
⋅
lbf)
(5)
Add the proper amount of ATF through the refill
hole.
NOTICE:
Refill amount differs depending on the related procedures
indicated below.
Related procedures
Refill amount
Removal and installation of oil pan
1.7 liters (1.8 us qts, 1.5 lmp.qts)
Removal of transmission valve body
assy
4.3 liters (4.5 us qts, 3.8 lmp.qts)
Removal of torque converter assy
5.4 liters (5.7 us qts, 4.8 lmp.qts)
(6)
Temporarily install the O–ring and refill plug.
Torque: 39 N
⋅
m (400 kgf
⋅
cm, 29 ft
⋅
lbf)
(7)
Lower down the vehicle.
(8)
Using SST, create a short–circuit between terminals
TC and CG of the DLC3.
SST
09843–18040
(9)
Start the engine and run at idle.
NOTICE:
The A/C switch must be turned off.
On models with active height control suspension &
adaptive variable suspension, turn the height control
switch off.
(10) Slowly move the shift lever from the P to the 2–L
position.
Return the shift lever to the P position.
D13654
D14231
When fluid
temperature
is low: off
When fluid
temperature
is correct: on
When fluid
temperature
is high: blinks
D14139
Overflow Plug
DI–530
–
DIAGNOSTICS
AUTOMATIC TRANSMISSION
724
(11) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or
from D to N, within 1.5 seconds. (Repeat this opera-
tion for 6 seconds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(12) Disconnect terminals TC and CG after confirming
the above condition.
(13) Idle the engine to raise the fluid temperature.
(14) Lift up the vehicle immediately after the meter indi-
cator light (ATF temperature warning light) comes
on.
NOTICE:
Add fluid only when the meter indicator light is on.
Perform this procedure while the engine is idling.
(15) Remove the overflow plug. If ATF overflows, pro-
ceed to [*2].
If ATF does not overflow, proceed to [*3].
HINT:
”Overflow” indicates the condition under which ATF drains out
from the overflow tube.
NOTICE:
Capacity of the overflow tube is approximately 3 cc.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст