Toyota Sequoia (2005). Manual — part 777
SA24B–02
F14284
Socket Wrench
F14286
F14287
SST
SST
F14288
SST
SST
–
SUSPENSION AND AXLE
REAR AXLE SHAFT
SA–101
3097
REASSEMBLY
1.
INSTALL BEARING ASSEMBLY
Position the backing plate on the bearing assembly and using
a press and 2 socket wrenches, install the serration bolts.
2.
INSTALL OIL DEFLECTOR AND GASKET
Position a new gasket and oil deflector on the axle shaft and
install a washer and nut to a new hub bolt, as shown in the il-
lustration, and install the hub bolt by torquing the nut.
3.
INSTALL REAR AXLE SHAFT TO BACKING PLATE
(a)
Install the backing plate, spring washer and bearing re-
tainer on the rear axle shaft.
(b)
Using SST and a press, install the rear axle shaft into the
backing plate.
SST
09631–12090, 09950–60020 (09951–01030)
4.
INSTALL SNAP RING TO AXLE SHAFT
Using a snap ring expander, install a new snap ring.
5.
INSTALL SPEED SENSOR ROTOR AND BEARING RE-
TAINER (DIFFERENTIAL SIDE)
Using SST and a press, install a new speed sensor rotor and
bearing retainer.
SST
09631–12090, 09950–60020 (09951–01030)
Standard length: 132.8
±
1.0 mm (5.228
±
0.039 in.)
SA17X–07
SA–102
–
SUSPENSION AND AXLE
REAR AXLE SHAFT
3098
INSTALLATION
Installation is in the reverse order of removal (See page
).
HINT:
After installation, fill the brake reservoir with brake fluid, bleed the brake system (See page
), check
for leaks and check the speed sensor signal (See page
SA24C–02
F14274
F14290
Nut
Washer
–
SUSPENSION AND AXLE
REAR WHEEL HUB BOLT
SA–103
3099
REAR WHEEL HUB BOLT
REPLACEMENT
1.
REMOVE REAR WHEEL
2.
REMOVE BRAKE CALIPER AND DISC
(a)
Remove the 2 bolts, brake caliper and disc.
(b)
Support the brake caliper securely.
3.
REMOVE HUB BOLT (See page
4.
INSTALL HUB BOLT
Install a washer and nut to a new hub bolt, as shown in the il-
lustration. Install the hub bolt by torquing the nut, while holding
the axle shaft using a brass bar or an equivalent.
5.
INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 105 N·m (1,070 kgf·cm, 77 ft·lbf)
6.
INSTALL REAR WHEEL
Torque: 110 N·m (1,150 kgf·cm, 83 ft·lbf)
SA15K–09
F14321
Oil Seal
Front Bearing
Bearing Spacer
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
Companion Flange
Rear Propeller Shaft
Washer
74 (750, 54)
Drive Pinion
2WD:
10 (102, 7.4)
74 (750, 54)
See page
Stud Bolt
Companion
Flange
See page
SA–104
–
SUSPENSION AND AXLE
REAR DIFFERENTIAL FRONT OIL SEAL
3100
REAR DIFFERENTIAL FRONT OIL SEAL
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст