Toyota Sequoia (2005). Manual — part 670
D13874
N·m (kgf·cm, ft·lbf)
: Specified torque
Non–reusable part
37 (377, 27)
Stabilizer Bar
Bushing
Stabilizer Bar Bracket
No. 1 Engine Under Cover
18 (185, 13)
Rear End Plate
Torque Converter Clutch
x 6
48 (490, 35)
Oil Cooler Pipe
34 (346, 25)
Gasket
Front Exhaust Pipe RH
48 (490, 35)
Gasket
Gasket
37 (377, 27)
Crossmember
Engine Rear
Mounting
Insulator
19.5 (199, 14)
14.5 (148, 11)
Transmission and
Transfer
88 (897, 65)
Rear Propeller Shaft
88 (897, 65)
Front Propeller Shaft
Heat Insulator
Front Exhaust Pipe LH
Clamp
71 (724, 52)
Gasket
48 (490, 35)
16 (164, 12)
65 (660, 48)
88 (897, 65)
88 (897, 65)
72 (734, 53)
Front Suspension
Member Bracket
33 (336, 24)
Front Suspension
Member Bracket
33 (336, 24)
62 (630, 46)
62 (630, 46)
12 (122, 9)
EM–90
–
ENGINE MECHANICAL
ENGINE UNIT (4WD)
2669
B17615
Engine Unit Assembly
A/C Compressor
PS Pump
Drive Plate
Oil Cooler Pipe
for Transmission
Rear Spacer
Stay
Front Spacer
x 8
Stay
Stay
N·m (kgf·cm, ft·lbf) : Specified torque
See page
1st 49 (500, 36)
2nd Turn 90
°
17 (175, 13)
A/C Compressor
Connector
38 (388, 28)
49 (500, 36)
38 (388, 28)
41 (420, 30)
x 6
–
ENGINE MECHANICAL
ENGINE UNIT (4WD)
EM–91
2670
EM11X–07
EM–92
–
ENGINE MECHANICAL
ENGINE UNIT (4WD)
2671
REMOVAL
1.
REMOVE FRONT EXHAUST PIPES
(See page
)
2.
REMOVE FRONT AND REAR PROPELLER SHAFTS
(See page
3.
REMOVE FRONT STABILIZER BAR
(See page
4.
REMOVE TRANSMISSION (See page
)
5.
REMOVE ENGINE HOOD
6.
REMOVE ENGINE UNDER COVER
7.
DISCONNECT BATTERY CABLES
(a)
Disconnect the clamp on battery negative (–) cable from
the No.2 relay box.
(b)
Disconnect the battery positive (+) terminal cable.
(c)
Disconnect the battery negative (–) cable from the left
fender apron.
8.
DRAIN ENGINE COOLANT
9.
REMOVE RADIATOR ASSEMBLY (See page
10.
REMOVE THROTTLE BODY COVER
11.
REMOVE AIR CLEANER AND INTAKE AIR CONNEC-
TOR ASSEMBLY
(a)
Disconnect the MAF meter connector.
(b)
Loosen the 3 bolts, and remove the air cleaner case.
(c)
Remove the suction hose from the intake air connector.
(d)
Disconnect the PS air hose, air inlet hose for EVAP, PCV
hose and MAF meter wire from the air intake connector.
(e)
Disconnect the intake air connector from the throttle body.
12.
REMOVE DRIVE BELT, FAN, FLUID COUPLING AND
FAN PULLEY
(a)
Loosen the 4 nuts holding the fluid coupling to the fan
bracket.
(b)
Remove the drive belt. (See page
(c)
Remove the 4 nuts, the fan, fluid coupling assembly and
fan pulley.
13.
DISCONNECT ENGINE WIRE FROM CABIN
(a)
Remove the glove compartment door.
(b)
Remove the lower No.2 panel.
(c)
Remove the 3 screws, and disconnect the ECM from the
body bracket.
(d)
Disconnect the 3 wire harness connectors from the ECM.
(e)
Disconnect the 2 wire harness connectors (cassette con-
nector).
B07536
Disconnect
A08905
A08907
A08936
–
ENGINE MECHANICAL
ENGINE UNIT (4WD)
EM–93
2672
(f)
Disconnect the engine wire from the engine wire bracket
and remove the 2 nuts, bolt and bracket.
(g)
Pull out the engine wire from the cowl panel.
14.
DISCONNECT HOSES, WIRES, CONNECTORS,
CLAMPS, GROMMET AND CABLES
(a)
Disconnect the 2 PS air hoses from hose clamp on the
No.3 RH timing belt cover.
(b)
Disconnect the generator wire.
(c)
Disconnect the generator connector.
(d)
Disconnect the hose clamp for the PS air hose.
(e)
Disconnect the PS air hose from the upper intake man-
ifold.
(f)
Disconnect the 2 heater hoses.
(g)
Disconnect the ground strap from the cowl panel.
(h)
Disconnect the fuel inlet hose and clamps.
(i)
Disconnect the fuel return hose and clamp.
(j)
Disconnect the air inlet hose from the charcoal canister.
(k)
Disconnect the EVAP hose from the charcoal canister.
(l)
Disconnect the brake booster tube.
15.
DISCONNECT A/C COMPRESSOR FROM ENGINE
(a)
Disconnect the A/C compressor connector.
(b)
Remove the 3 bolts, and disconnect the A/C compressor
from the engine.
HINT:
Suspend the A/C compressor securely.
16.
DISCONNECT PS PUMP FROM ENGINE
Remove the 3 bolts, and disconnect the PS pump from the en-
gine.
HINT:
Suspend the PS pump securely.
17.
REMOVE OIL COOLER PIPES FOR TRANSMISSION
(a)
Remove the 3 bolts and 3 stays.
(b)
Loosen the 2 union nuts, and remove the 2 oil cooler
pipes.
18.
REMOVE ENGINE ASSEMBLY FROM VEHICLE
(a)
Attach the engine chain hoist to the engine hangers.
(b)
Remove the 4 bolts holding the engine mounting brackets
to the frame brackets.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст