Toyota Urban Cruiser (2015 year). Instruction — part 13
2-1. Driving procedures
NOTICE
■ If you get a flat tire while driving
A flat or damaged tire may cause the following situations. Hold the steering
wheel firmly and gradually press the brake pedal to slow down the vehicle.
●It may be difficult to control your vehicle.
●The vehicle will make abnormal sounds or vibrations.
●The vehicle will lean abnormally.
Information on what to do in case of a flat tire. (→P. 449, 464)
■ When encountering flooded roads
Do not drive on a road that has flooded after heavy rain etc. Doing so may
cause the following serious damage to the vehicle.
●Engine stalling
●Short in electrical components
● Engine damage caused by water immersion
In the event that you drive on a flooded road and the vehicle is flooded, be
sure to have any authorized Toyota dealer or repairer, or another duly quali-
fied and equipped professional check the following.
●Brake function
●Changes in quantity and quality of oil and fluid used for the engine, trans-
mission, transfer (4WD models), differential (4WD models), etc.
● Lubricant condition for the propeller shaft (4WD models), bearings and
suspension joints (where possible) and the function of all joints, bearings,
etc.
180
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
Engine (ignition) switch (vehicles without smart entry & start system)
■ Starting the engine
Gasoline engine
STEP
1
Check that the parking brake is set.
STEP
2
Check that the shift lever is set in “N”.
STEP
3
Sit in the driver’s seat and firmly depress the clutch pedal.
STEP
4
Turn the engine switch to the “START” position and start
the engine.
2
The engine will crank until it start or for up to 30 seconds, which-
ever is less.
Continue depressing the clutch pedal until the engine is com-
pletely started.
Diesel engine
STEP
1
Check that the parking brake is set.
STEP
2
Check that the shift lever is set in “N”.
STEP
3
Sit in the driver’s seat and firmly depress the clutch pedal.
STEP
4
Turn the engine switch to the “ON” position.
indicator
turns on.
STEP
5
After
indicator goes out, turn the engine switch to the
“START” position and start the engine.
181
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
■ Engine (ignition) switch
“LOCK”
The steering wheel is locked
and the key can be removed.
“ACC”
Some electrical components
such as the audio system can
be used.
“ON”
All electrical components can
be used.
“START”
For starting the engine.
182
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
■ Turning the key from “ACC” to “LOCK”
STEP
1
Shift the shift lever to “N”.
STEP
2
Push in the key and turn to the “LOCK”
position.
2
■ If the engine does not start
The engine immobilizer system may not have been deactivated. (→P. 110)
■ When the steering lock cannot be released
When starting the engine, the engine
switch may seem stuck in the “LOCK”
position. To free it, turn the key while turn-
ing the steering wheel slightly in either
direction.
■ Key reminder function
A buzzer sounds if the driver’s door is opened while the engine switch is in
the “LOCK” or “ACC” position to remind you to remove the key.
183
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
CAUTION
■ When starting the engine
Always start the engine while sitting in the driver’s seat. Do not press the
accelerator pedal while starting the engine under any circumstances.
Doing so may cause an accident resulting in death or serious injury.
■ Caution when driving
Do not turn the engine switch to the “LOCK” position while driving. If, in an
emergency, you must turn the engine off while the vehicle is moving, turn the
engine switch only to the “ACC” position to stop the engine. An accident may
result if the engine is stopped while driving.
NOTICE
■ To prevent battery discharge
Do not leave the engine switch in the “ACC” or “ON” position for long periods
of time without the engine running.
■ When starting the engine
●Do not crank for more than 30 seconds at a time. This may overheat the
starter and wiring systems.
●Do not race a cold engine.
● If the engine becomes difficult to start or stalls frequently, have the engine
checked immediately.
184
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
Engine (ignition) switch (vehicles with smart entry & start system)
Performing the following operations when carrying the electronic
key on your person starts the engine or changes “ENGINE START
STOP” switch modes.
■ Starting the engine
STEP
1
Check that the parking brake is set.
STEP
2
Check that the shift lever is set in “N”.
STEP
3
Sit in the driver’s seat and firmly depress the clutch pedal.
2
The “ENGINE START STOP” switch indicator turns green.
STEP
4
Press the
“ENGINE START
STOP” switch.
The engine can be started
from any
“ENGINE START
STOP” switch mode.
Continue depressing the clutch
pedal until the engine is com-
pletely started. The engine will
crank until it starts or for up to
25 seconds, whichever is less.
Diesel engine only:
indi-
cator turns on. The engine
begins starting after the indica-
tor light goes out.
185
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
■ Stopping the engine
STEP
1
Stop the vehicle.
STEP
2
Shift the shift lever to “N”.
STEP
3
Set the parking brake. (→P. 194)
STEP
4
Press the “ENGINE START STOP” switch.
STEP
5
Release the brake pedal and check that the indicator on the
“ENGINE START STOP” switch is off.
■ Changing “ENGINE START STOP” switch mode
Modes can be changed by pressing the “ENGINE START
STOP” switch with the clutch pedal released.
(The mode
changes each time the switch is pressed.)
OFF
Emergency flashers can be
used.
ACCESSORY mode
Some electrical components
such as the audio system can
be used.
The “ENGINE START STOP”
switch indicator turns amber.
IGNITION ON mode
All electrical components can
be used.
The “ENGINE START STOP”
switch indicator turns amber.
186
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
■ If the engine does not start
The engine immobilizer system may not have been deactivated. (→P. 110)
■ When the steering lock cannot be released
Make sure that the steering wheel is
released.
To released the steering wheel lock, gen-
tly turn the wheel left or right while press-
ing the “ENGINE START STOP” switch.
2
If the steering wheel lock dose not
release, the
“ENGINE START STOP”
switch indicator will flash green.
■ When the “ENGINE START STOP” switch indicator flashes in amber
The system may be malfunctioning. Have the vehicle inspected by any
authorized Toyota dealer or repairer, or another duly qualified and equipped
professional, immediately.
■ Auto power off function
If the vehicle is left in the ACCESSORY mode for more than an hour, the
“ENGINE START STOP” switch will automatically turn OFF.
■ Electronic key battery depletion
→P. 42
■ When the electronic key battery is discharged
→P. 484
■ Conditions affecting operation
→P. 40
■ Note for the smart entry & start system
→P. 43
187
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
CAUTION
■ When starting the engine
Always start the engine while sitting in the driver’s seat. Do not depress the
accelerator while starting the engine under any circumstances.
Doing so may cause an accident resulting in death or serious injury.
■ Stopping the engine in an emergency
If you want to stop the engine in an emergency while driving the vehicle,
push and hold the “ENGINE START STOP” switch for more than 3 seconds.
However, do not touch the “ENGINE START STOP” switch while driving
except in an emergency. Turning the engine off while driving will not cause
loss of steering or braking control, but the power assist to these systems will
be lost. This will make it more difficult to steer and brake, so you should pull
over and stop the vehicle as soon as it is safe to do so.
NOTICE
■ To prevent battery discharge
Do not leave the “ENGINE START STOP” switch in the ACCESSORY or
IGNITION ON mode for long periods without the engine running.
■ When starting the engine
●Do not race a cold engine.
● If the engine becomes difficult to start or stalls frequently, have the engine
checked immediately.
188
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
Manual transmission
■ Shifting the shift lever
Fully depress the clutch pedal
before operating the shift
lever, and then release it
slowly.
2
■ Shifting the shift lever to “R”
Shift the shift lever to the “R”
position while lifting up the ring
section.
189
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
Gear Shift Indicator
The Gear Shift Indicator display is a guide to help the driver achieve
improved fuel economy and reduced exhaust emissions within limits
of engine performance.
Upshifting
Downshifting
■ Gear Shift Indicator display
The Gear Shift Indicator may not be displayed when your foot is placed on
the clutch pedal.
190
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
■ Maximum allowable speeds
Observe the following maximum allowable speeds in each gear when maxi-
mum acceleration is necessary.
km/h (mph)
Maximum speed
Shift
Diesel engine
position
Gasoline engine
2WD models
4WD models
1
43 (27)
42 (26)
40 (25)
2
2
79 (49)
78 (48)
74 (46)
3
116 (72)
114 (71)
108 (67)
4
147 (91)
154 (96)
146 (91)
5
175 (109)
175 (109)
175 (109)
CAUTION
■ Gear Shift Indicator display
Refer to the display while considering actual traffic and road while driving
conditions. Failure to exercise judgment may lead to an accident.
191
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
NOTICE
■ To prevent damage to the transmission
● Do not shift the shift lever to “R” without
depressing the clutch pedal.
●Do not lift up the ring section except when shifting the lever to “R”.
●Shift the shift lever to “R” only when the vehicle is stationary.
192
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
Turn signal lever
The turn signal lever can be used to show the following intentions of
the driver:
Right turn
Left turn
Lane change to the right
(push and hold the lever
partway)
2
The right hand signal will flash
until you release the lever.
Lane change to the left
(push and hold the lever
partway)
The left hand signal will flash
until you release the lever.
■ Turn signals can be operated when
Vehicles without smart entry & start system
The engine switch is in the “ON” position.
Vehicles with smart entry & start system
The “ENGINE START STOP” switch is in the IGNITION ON mode.
■ If the indicators flash faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned
out.
193
URBAN CRUISER_OM_OM52F47E_(EE)
2-1. Driving procedures
Parking brake
Sets the parking brake
Fully set the parking brake
while depressing the brake
pedal.
Releases the parking brake
Slightly raise the lever and
lower it completely while press-
ing the button.
■ Usage in winter time
See “Winter driving tips” for parking brake usage in winter time. (→P. 235)
NOTICE
■ Before driving
Fully release the parking brake.
Driving the vehicle with the parking brake set will lead to brake components
overheating, which may affect braking performance and increase brake
wear.
194
URBAN CRUISER_OM_OM52F47E_(EE)
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст