Toyota Tundra (2015 year). Manual — part 2131
OK
MEASUREMENT CONDITION
MIRROR POSITION
SPECIFIED CONDITION
Battery positive (+) → Terminal
8 (MF)
NG
REPLACE OUTER REAR VIEW MIRROR LH
7.
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR
CONTROL ECU)
(a) Disconnect the N7 ECU connector.
(b) Disconnect the N5 mirror connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
N7-1 (MR+) - N5-7 (MR)
Always
Below 1 Ω
N7-2 (MR-) - N5-8 (MF)
N5-7 (MR) - Body ground
Always
10 kΩ or higher
MIRROR: POWER MIRROR CONTROL SYSTEM (w/ Memory): Pow...
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
N5-8 (MF) - Body ground
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
END (OUTER MIRROR CONTROL ECU IS
DEFECTIVE)
8.
INSPECT OUTER REAR VIEW MIRROR RH
(a) Remove the mirror RH
.
(b) For each mirror position: Disconnect the battery, set the mirror position by hand, connect the
battery, and check the retractable mirror's movement.
NOTICE:
Disconnect and reconnect the battery once between each mirror position check.
The mirror position cannot be changed manually when the battery is connected. To change the mirror
position manually, the battery must be disconnected first.
OK:
MEASUREMENT CONDITION
MIRROR POSITION
SPECIFIED CONDITION
Battery positive (+) → Terminal
7 (MR)
Battery negative (-) →
Forward position (A)
Moves from (A) to retracted
position (E)
MIRROR: POWER MIRROR CONTROL SYSTEM (w/ Memory): Pow...
OK
MEASUREMENT CONDITION
MIRROR POSITION
SPECIFIED CONDITION
Terminal 8 (MF)
Battery negative (-) →
Terminal 7 (MR)
Battery positive (+) → Terminal
8 (MF)
Forward position (A)
Does not move
Battery positive (+) → Terminal
7 (MR)
Battery negative (-) →
Terminal 8 (MF)
Position between forward position (A) and
driving position (C)
Moves from (B) to retracted
position (E)
Battery negative (-) →
Terminal 7 (MR)
Battery positive (+) → Terminal
8 (MF)
Position between forward position (A) and
driving position (C)
Moves from (B) to forward
position (A)
Battery positive (+) → Terminal
7 (MR)
Battery negative (-) →
Terminal 8 (MF)
Driving position (C)
Moves from (C) to retracted
position (E)
Battery negative (-) →
Terminal 7 (MR)
Battery positive (+) → Terminal
8 (MF)
Driving position (C)
Does not move
Battery positive (+) → Terminal
7 (MR)
Battery negative (-) →
Terminal 8 (MF)
Position between driving position (C) and
retracted position (E)
Moves from (D) to retracted
position (E)
Battery negative (-) →
Terminal 7 (MR)
Battery positive (+) → Terminal
8 (MF)
Position between driving position (C) and
retracted position (E)
Moves from (D) to driving
position (C)
Battery positive (+) → Terminal
7 (MR)
Battery negative (-) →
Terminal 8 (MF)
Retracted position (E)
Does not move
Battery negative (-) →
Terminal 7 (MR)
Battery positive (+) → Terminal
8 (MF)
Retracted position (E)
Moves from (E) to driving
position (C)
NG
REPLACE OUTER REAR VIEW MIRROR RH
MIRROR: POWER MIRROR CONTROL SYSTEM (w/ Memory): Pow...
9.
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR
CONTROL ECU)
(a) Disconnect the N7 ECU connector.
(b) Disconnect the M6 mirror connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
N7-5 (MR+) - M6-7 (MR)
Always
Below 1 Ω
N7-6 (MR-) - M6-8 (MF)
M6-7 (MR) - Body ground
Always
10 kΩ or higher
M6-8 (MF) - Body ground
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
END (OUTER MIRROR CONTROL ECU IS
DEFECTIVE)
10.
INSPECT OUTER MIRROR SWITCH
MIRROR: POWER MIRROR CONTROL SYSTEM (w/ Memory): Pow...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст