Toyota Tundra (2015 year). Manual — part 1354
(a) Remove the 3 bolts and disconnect the No. 1 water by-pass
pipe.
42. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
43. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
44. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
45. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
46. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
47. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
48. REMOVE STARTER COVER
49. REMOVE STARTER ASSEMBLY
50. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(a) for 2WD:
Refer to the following procedures
.
(b) for 4WD:
Refer to the following procedures
.
51. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)
52. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)
53. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
(a) Using SST, hold the crankshaft.
SST: 09213-70011
SST: 09330-00021
1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVAL...
(b) Remove the 10 bolts, rear drive plate spacer, drive plate and
crankshaft angle sensor rotor.
54. REMOVE ENGINE ASSEMBLY
(a) Install 2 engine hangers with 2 bolts as shown in the illustration.
Torque:
43 N·m {438 kgf·cm, 32ft·lbf}
Engine hanger
12281-38150
Bolt
90119-A0166
(b) Attach an engine sling device and hang the engine with a chain block.
(c) Remove the 4 engine mounting insulator bolts.
(d) Lift the engine out from the vehicle slowly and carefully.
NOTICE:
(a) Install the engine to an engine stand with the bolts.
(b) Remove the 2 bolts and 2 engine hangers.
1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVAL...
1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVAL...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000031RQ023X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly RH,
cylinder head sub-assembly LH, No. 1 camshaft sub-assembly, No. 2 camshaft sub-assembly, No. 3
camshaft sub-assembly, No. 4 camshaft sub-assembly, camshaft timing gear RH, camshaft timing gear LH,
camshaft timing exhaust gear RH, camshaft timing exhaust gear LH, piston or piston ring
.
1. REMOVE ENGINE FROM ENGINE STAND
(a) Install the 2 engine hangers with the 2 bolts as shown in the
illustration.
Torque:
43 N·m {438 kgf·cm, 32ft·lbf}
Engine hanger
12281-38150
Bolt
90119-A0166
(b) Attach an engine sling device and hang the engine with a chain block.
(c) Remove the bolts and engine assembly from the engine stand.
2. INSTALL ENGINE ASSEMBLY
(a) Slowly lower the engine assembly into the engine compartment.
NOTICE:
1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALL...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст