Toyota Tundra (2015 year). Manual — part 2639
(a) Apply high-temperature grease to the plunger hook.
Torque:
7.5 N·m {76 kgf·cm, 66in·lbf}
(d) Connect the lead wire to the magnet starter switch with the nut.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
3UR-FE STARTING: STARTER: REASSEMBLY; 2015 MY Tundra [0...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002MDK041X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE STARTING: STARTER: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL STARTER ASSEMBLY
(a) Install the flywheel housing side cover.
(b) Install the starter with the 2 bolts.
Torque:
37 N·m {377 kgf·cm, 27ft·lbf}
(c) Install the starter wire with the nut.
Torque:
9.8 N·m {100 kgf·cm, 87in·lbf}
(d) Connect the starter connector.
(e) Attach the 2 wire harness clamps.
2. INSTALL STARTER COVER
(a) Install the starter cover with the 3 bolts.
Torque:
12 N·m {117 kgf·cm, 8ft·lbf}
3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
4. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
5. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(a) Install a new gasket and the exhaust pipe to the exhaust manifold RH with 3 new nuts.
Torque:
54 N·m {554 kgf·cm, 40ft·lbf}
(b) Install a new gasket and the exhaust pipe to the center exhaust pipe with the 2 bolts.
Torque:
48 N·m {489 kgf·cm, 35ft·lbf}
(c) Connect the air fuel ratio sensor connector.
(d) Connect the heated oxygen sensor connector and attach the 2 clamps.
6. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
(b) Install the O-ring to the guide.
(c) Install the dipstick guide with the bolt.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
(d) Install the dipstick.
7. INSTALL GENERATOR ASSEMBLY
(a) Install the generator with the 3 bolts and nut.
Torque:
43 N·m {439 kgf·cm, 32ft·lbf}
(b) Connect the generator connector.
(c) Connect the generator wire with the nut.
Torque:
9.8 N·m {100 kgf·cm, 87in·lbf}
(d) Install the terminal cap.
(e) Install the harness bracket to the generator with the bolt.
Torque:
31 N·m {316 kgf·cm, 23ft·lbf}
8. CONNECT VANE PUMP ASSEMBLY
3UR-FE STARTING: STARTER: INSTALLATION; 2015 MY Tundra [...
HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed.
(a) Connect the vane pump to the timing chain cover with the 2
bolts.
Torque:
28 N·m {286 kgf·cm, 21ft·lbf}
(b) Attach the 2 clamps and connect the power steering oil
pressure switch connector.
9. INSTALL FRONT FENDER APRON SEAL RH
10. INSTALL FAN AND GENERATOR V BELT
11. INSTALL AIR CLEANER ASSEMBLY
12. INSTALL AIR CLEANER HOSE ASSEMBLY
13. INSTALL V-BANK COVER SUB-ASSEMBLY
14. INSTALL NO. 1 ENGINE UNDER COVER
15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
3UR-FE STARTING: STARTER: INSTALLATION; 2015 MY Tundra [...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст