Toyota Tundra (2015 year). Manual — part 2991
OK
3.
CHECK CONNECTORS
(a) Disconnect the connectors from the center airbag sensor and front airbag sensor RH.
(b) Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are
not damaged.
OK:
The connectors are not deformed or damaged.
NG
REPLACE HARNESS AND CONNECTOR
4.
CHECK FRONT AIRBAG SENSOR RH CIRCUIT
(a) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard voltage:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
A1-1 (-SR) - Body ground
Ignition switch ON
Below 1 V
A1-2 (+SR) - Body ground
(d) Turn the ignition switch off.
(e) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
OK
NOTICE:
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
A1-1 (-SR) - A1-2 (+SR)
Always
Below 1 Ω
(h) Disconnect the service wire from connector B.
(i) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
A1-1 (-SR) - A1-2 (+SR)
Always
1 MΩ or higher
A1-1 (-SR) - Body ground
A1-2 (+SR) - Body ground
NG
GO TO STEP 6
5.
CHECK FRONT AIRBAG SENSOR RH
(a) Connect the connectors to the center airbag sensor.
(b) Interchange the front airbag sensor LH with RH and connect
the connectors to them.
(c) Connect the negative (-) terminal cable to the battery, and
wait for at least 2 seconds.
(d) Turn the ignition switch to ON, and wait for at least 60
seconds.
(e) Clear the DTCs stored in the memory
.
(f) Turn the ignition switch off.
(g) Turn the ignition switch to ON, and wait for at least 60
seconds.
(h) Check for DTCs
.
Result
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1610/...
RESULT
PROCEED TO
DTC B1610 is output
A
DTC B1615 is output
B
DTC B1610 and B1615 are not output
C
HINT:
Codes other than DTC B1610 and B1615 may be output at this
time, but they are not related to this check.
A
GO TO STEP 12
B
REPLACE FRONT AIRBAG SENSOR RH
C
USE SIMULATION METHOD TO CHECK
6.
CHECK INSTRUMENT PANEL WIRE
(a) Disconnect the instrument panel wire connector from the engine room main wire.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard voltage:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
AJ1-1 (-SR) - Body ground
Ignition switch ON
Below 1 V
AJ1-2 (+SR) - Body ground
(e) Turn the ignition switch off.
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1610/...
OK
(f) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
AJ1-1 (-SR) - AJ1-2 (+SR)
Always
Below 1 Ω
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
AJ1-1 (-SR) - AJ1-2 (+SR)
Always
1 MΩ or higher
AJ1-1 (-SR) - Body ground
AJ1-2 (+SR) - Body ground
NG
REPLACE INSTRUMENT PANEL WIRE
OK
REPLACE ENGINE ROOM MAIN WIRE
7.
CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor and the front airbag
sensor LH.
OK:
The connectors are properly connected.
NG
CONNECT CONNECTORS PROPERLY
8.
CHECK CONNECTORS
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1610/...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст