Toyota Tundra (2015 year). Manual — part 2143
TESTER DISPLAY
MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC
NOTE
Hall IC2 Pulse
-
Ignition (Direct
Signal)
Ignition switch signal/ON or OFF
ON: Ignition switch ON
OFF: Ignition switch off
-
Ignition (MPX)
Ignition switch signal (MPX
signal)/ON or OFF
ON: Ignition switch ON
OFF: Ignition switch off
-
Door Courtesy
Driver's door courtesy light switch
signal/ON or OFF
ON: Driver's door is open
OFF: Driver's door is closed
-
Door Key Close
Operation
ON: Door key cylinder is turned to
UNLOCK position using key
OFF: Door key cylinder is not turned to
UNLOCK
-
Door Key Open
Operation
ON: Door key cylinder is turned to
LOCK position using key
OFF: Door key cylinder is not turned to
LOCK
-
Key Off
Permission
ON: Driver's side door is not closed
within 45 sec after ignition switch is
turned off
OFF: Any status except "ON" status
-
Door Key Related
(Open)
-
Door Key Related
(Close)
-
Door Key Related
Operation
Direction for key-linked
operation/Tilt or Slide
-
Down Switch
Failure (Current)
Down switch failure signal
(Current)/ON or OFF
-
Up Switch Failure
(Current)
Up switch failure signal
(Current)/ON or OFF
-
SLIDING ROOF: SLIDING ROOF SYSTEM: DATA LIST / ACTIVE ...
TESTER DISPLAY
MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC
NOTE
Close Switch
Failure (Current)
Close switch failure signal
(Current)/ON or OFF
-
Open Switch
Failure (Current)
Open switch failure signal
(Current)/ON or OFF
-
Down Switch
Failure (Past)
Down switch failure signal
(Past)/ON or OFF
-
Up Switch Failure
(Past)
Up switch failure signal (Past)/ON
or OFF
-
Close Switch
Failure (Past)
Close switch failure signal
(Past)/ON or OFF
-
Open Switch
Failure (Past)
Open switch failure signal
(Past)/ON or OFF
-
Number of
Trouble Codes
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated
without removing any parts. This non-intrusive functional inspection can be very useful because
intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early
in troubleshooting is one way to save diagnostic time. Data List information can be displayed while
performing Active Test.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
(d) Enter the following menus:
Sliding Roof
TESTER
TEST PART
CONTROL RANGE
DIAGNOSTIC
SLIDING ROOF: SLIDING ROOF SYSTEM: DATA LIST / ACTIVE ...
DISPLAY
NOTE
Slide Roof
SLIDING ROOF: SLIDING ROOF SYSTEM: DATA LIST / ACTIVE ...
Last Modified: 9-16-2014
6.6 S
Doc ID: RM000002BFQ02DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SLIDING ROOF: SLIDING ROOF SYSTEM: DIAGNOSTIC TROUBLE CODE CHART; 2015 MY Tundra
[08/2014 - ]
DIAGNOSTIC TROUBLE CODE CHART
If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of
the code, refer to the "See page" below.
DETECTION ITEM
TROUBLE AREA
SEE PAGE
B2341
Sensor (Motor) Failure
Switch Failure
- Harness and connector
Position Initialization Incomplete
- Harness and connector
Position Failure
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст