Toyota Tundra (2015 year). Manual — part 2105
OK
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
4.
INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH
(a) Remove the front door courtesy light switch RH
.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION SWITCH CONDITION SPECIFIED CONDITION
1 - Body ground
Not pushed
Below 1 Ω
Pushed
10 kΩ or higher
NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH
RH
5.
CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH -
MAIN BODY ECU)
LIGHTING: LIGHTING SYSTEM: Door Courtesy Switch Circuit; 201...
(a) Disconnect the Q5 switch connector.
(b) Disconnect the J3 ECU connector.
(c) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
Q5-1 - J3-21 (PCTY)
Always
Below 1 Ω
Q5-1 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
6.
INSPECT REAR DOOR COURTESY LIGHT SWITCH LH
(a) Remove the rear door courtesy light switch LH
.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION SWITCH CONDITION SPECIFIED CONDITION
1 - Body ground
Not pushed
Below 1 Ω
Pushed
10 kΩ or higher
NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH
LH
LIGHTING: LIGHTING SYSTEM: Door Courtesy Switch Circuit; 201...
OK
7.
CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN
BODY ECU)
(a) Disconnect the P6 switch connector.
(b) Disconnect the DC ECU connector.
(c) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
P6-1 - DC-2 (LCTY)
Always
Below 1 Ω
P6-1 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
8.
INSPECT REAR DOOR COURTESY LIGHT SWITCH RH
LIGHTING: LIGHTING SYSTEM: Door Courtesy Switch Circuit; 201...
OK
(a) Remove the rear door courtesy light switch RH
.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION SWITCH CONDITION SPECIFIED CONDITION
1 - Body ground
Not pushed
Below 1 Ω
Pushed
10 kΩ or higher
NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH
RH
9.
CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN
BODY ECU)
(a) Disconnect the Q6 switch connector.
(b) Disconnect the J3 ECU connector.
(c) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
Q6-1 - J3-25 (RRCY)
Always
Below 1 Ω
Q6-1 - Body ground
Always
10 kΩ or higher
LIGHTING: LIGHTING SYSTEM: Door Courtesy Switch Circuit; 201...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст