Toyota Tundra (2015 year). Manual — part 1957
A
NEXT
(c) Start the engine.
(d) Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.
(e) Perform the drive pattern.
(1) Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.
(2) Drive the vehicle between 60 and 80 km/h (35 and 50 mph) for 5 minutes.
(f) Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.
(g) Read the DTCs.
Result
RESULT
PROCEED TO
P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
A
Only P0607
B
No DTC output
C
B
REPLACE ECM
C
GO TO STEP 6
5.
INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
(a) Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.
HINT:
If P0136 or P0156 is output, troubleshoot for that DTC first
. Then proceed to "INSPECT ECM".
If P0137 or P0157 is output, troubleshoot for that DTC first
. Then proceed to "INSPECT ECM".
If P0138 or P0158 is output, troubleshoot for that DTC first
. Then proceed to "INSPECT ECM".
INSPECT ECM
(a) Clear DTC
.
(b) Stop the engine and wait for 30 minutes.
(c) Connect the Techstream to the DLC3.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0607; Contr...
(d) Start the engine and allow it to idle for 2 minutes.
(e) Turn the Techstream on.
(f) Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.
(g) Check the DTCs.
Result
RESULT
PROCEED TO
DTC is not output
A
P0607 is output
B
B
REPLACE ECM
A
END
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0607; Contr...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000002Z1R0G2X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060A; Internal Control Module Monitoring Processor
Performance; 2015 MY Tundra [08/2014 - ]
DTC
P060A
Internal Control Module Monitoring Processor Performance
DESCRIPTION
detected, a DTC is output.
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
P060A
When either condition below is met:
ECM main CPU error
ECM sub CPU error
Electronic throttle monitoring CPU error
ECM
MONITOR STRATEGY
Related DTCs
None
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Duration
-
MIL operation
Immediate
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
None
TYPICAL MALFUNCTION THRESHOLDS
When either condition below is met:
Condition 1 or 2
1. When all conditions below are met:
-
- CPU reset
1 time or more
- Learned TP - Learned APP
0.4 V or more
- Electronic throttle actuator
OFF
2. CPU reset
2 times or more
CONFIRMATION DRIVING PATTERN
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060A; Intern...
Connect the Techstream to the DLC3.
1.
Turn the ignition switch to ON and turn the Techstream on.
2.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
3.
Turn the ignition switch off and wait for at least 30 seconds.
4.
Turn the ignition switch to ON and turn the Techstream on.
5.
Wait 16 seconds or more [A].
6.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
7.
Read the Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
8.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
9.
Input the DTC: P060A.
10.
Check the DTC judgment result.
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
11.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and
12.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060A; Intern...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст