Toyota Tundra (2015 year). Manual — part 1715
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002OPA03GX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD: REPAIR; 2015 MY Tundra [08/2014 - ]
REPAIR
1. REPAIR INTAKE VALVE SEAT
NOTICE:
seat width is more than the specification.
(b) Using 30° and 60° cutters, correct the valve seat so that the
valve seat width should be maintained within the specified
1.1 to 1.5 mm (0.0433 to 0.0591 in.)
(c) Hand-lap the valve and valve seat with an abrasive compound.
(d) Check the valve seating position.
2. REPAIR EXHAUST VALVE SEAT
NOTICE:
seat width is more than the specification.
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD: REPAIR; 20...
(b) Using 30° and 60° cutters, correct the valve seat so that the
valve seat width should be maintained within the specified
1.1 to 1.5 mm (0.0433 to 0.0591 in.)
(c) Hand-lap the valve and valve seat with an abrasive compound.
(d) Check the valve seating position.
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD: REPAIR; 20...
Last Modified: 9-16-2014
6.6 K
Doc ID: RM000002S5103FX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (for Bank 1): COMPONENTS; 2015 MY
Tundra [08/2014 - ]
COMPONENTS
ILLUSTRATION
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (fo...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002S5203QX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (for Bank 1): REMOVAL; 2015 MY Tundra
[08/2014 - ]
REMOVAL
1. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
(a) Remove the exhaust manifold LH
.
2. REMOVE CAMSHAFTS (for Bank 1)
(a) Remove the camshafts
.
3. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
(a) Remove the 16 valve rocker arms from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
4. REMOVE VALVE LASH ADJUSTER ASSEMBLY
(a) Remove the 16 valve lash adjusters from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
5. REMOVE VALVE STEM CAP
(a) Remove the 16 valve stem caps from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
6. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH
(a) Uniformly loosen and remove the 2 bolts in the sequence
shown in the illustration.
(b) Using a 10 mm bi-hexagon wrench, uniformly loosen the 10
cylinder head bolts in the sequence shown in the illustration.
Remove the 10 cylinder head bolts and plate washers.
HINT:
Be sure to arrange the removed parts for each installation
position separately.
NOTICE:
Be careful not to drop washers into the cylinder head.
Head warpage or cracking could result from removing bolts in
an incorrect order.
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (fo...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст