Toyota Tundra (2015 year). Manual — part 1724
(b) Remove the air cleaner element.
(c) Remove the 2 bolts and air cleaner case.
13. REMOVE INLET RADIATOR HOSE
14. REMOVE OUTLET RADIATOR HOSE
15. REMOVE RADIATOR GRILLE SUB-ASSEMBLY
16. REMOVE RADIATOR SIDE DEFLECTOR RH
17. REMOVE RADIATOR SIDE DEFLECTOR LH
18. REMOVE FAN & GENERATOR V BELT
19. REMOVE FAN SHROUD
20. REMOVE RADIATOR ASSEMBLY
21. DISCONNECT FUEL MAIN AND RETURN HOSE
(a) Remove the fuel pipe clamp.
(b) Disconnect the fuel main and return hoses
.
22. DISCONNECT WIRE HARNESS AND HOSE
3UR-FBE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVA...
(a) Disconnect the union to check valve hose.
(b) Disconnect the purge line hose.
(c) Disconnect the heater hoses.
(d) Disconnect the clamp and ECM connector.
HINT:
Refer to the following procedures to disconnect the ECM connector
.
(e) Disconnect the 4 connectors from the connector holder block.
(f) Remove the nut and connector bracket and disconnect the 2
air pump connectors.
(g) Remove the bolt and disconnect the ground wire.
(h) Disconnect the 2 air injection system hoses.
3UR-FBE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVA...
(i) Remove the nut and disconnect the wire from the positive (+)
battery cable.
(j) Disconnect the cable from the positive (+) battery terminal.
(k) Remove the bolt and disconnect the ground wire.
(l) Disconnect the 4 air injection control driver connectors.
(m) Remove the nut and disconnect the wire and 2 clips from the engine room junction block.
(n) Disconnect the 2 connectors and 2 clips from the engine room junction block.
23. DISCONNECT COOLER COMPRESSOR ASSEMBLY
24. DISCONNECT VANE PUMP ASSEMBLY
25. REMOVE GENERATOR ASSEMBLY
26. REMOVE EXHAUST PIPE ASSEMBLY
(a) Remove the exhaust pipe assembly
.
27. REMOVE PROPELLER SHAFT ASSEMBLY
(a) Remove the propeller shaft
.
28. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(a) Remove the front propeller shaft
.
29. REMOVE FRONT FENDER APRON SEAL RH
30. REMOVE FRONT FENDER APRON SEAL REAR RH
31. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
32. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
33. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
34. REMOVE STARTER COVER
35. REMOVE STARTER ASSEMBLY
36. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(a) Remove the automatic transmission
.
37. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
3UR-FBE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVA...
(a) Using SST, hold the crankshaft.
SST: 09213-70011
SST: 09330-00021
(b) Remove the 10 bolts, rear drive plate spacer, drive plate and
crankshaft position sensor rotor.
38. REMOVE NO. 1 WATER BY-PASS PIPE
(a) Remove the 2 bolts and disconnect the hose. Then remove
the water by-pass pipe.
39. REMOVE ENGINE ASSEMBLY
(a) Install the 2 engine hangers with the 2 bolts as shown in the
illustration.
Torque:
43 N·m {438 kgf·cm, 32ft·lbf}
ITEM
PART NO.
Engine hanger
12281-38150
Bolt
90119-A0166
(b) Attach an engine sling device and hang the engine with a chain block.
3UR-FBE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVA...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст