Toyota Tundra (2015 year). Manual — part 2970
NEXT
NEXT
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000002ZF800MX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SEAT BELT: SEAT BELT WARNING SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING; 2015 MY
Tundra [08/2014 - ]
HOW TO PROCEED WITH TROUBLESHOOTING
HINT:
Use the following procedures to troubleshoot the seat belt warning system.
*: Use the Techstream.
1.
VEHICLE BROUGHT TO WORKSHOP
2.
INSPECT BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
3.
CHECK FOR DTC*
Result:
RESULT
PROCEED TO
DTC output does not reoccur
A
CAN communication system DTC output reoccurs
B
Airbag system DTC output reoccurs
C
SEAT BELT: SEAT BELT WARNING SYSTEM: HOW TO PROCEED ...
A
NEXT
NEXT
NEXT
RESULT
PROCEED TO
Occupant classification system DTC output reoccurs
D
B
GO TO CAN COMMUNICATION SYSTEM
C
GO TO AIRBAG SYSTEM
D
GO TO OCCUPANT CLASSIFICATION SYSTEM
4.
PROBLEM SYMPTOMS TABLE
(a) Refer to the problem symptoms table
.
5.
OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) Operation check
(b) Data List / Active Test
REPAIR OR REPLACE
7.
CONFIRMATION TEST
SEAT BELT: SEAT BELT WARNING SYSTEM: HOW TO PROCEED ...
NEXT
END
SEAT BELT: SEAT BELT WARNING SYSTEM: HOW TO PROCEED ...
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000005KST002X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SEAT BELT: SEAT BELT WARNING SYSTEM: OPERATION CHECK; 2015 MY Tundra [08/2014 - ]
OPERATION CHECK
1. INSPECT DRIVER SEAT BELT WARNING LIGHT
HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front
passenger seat.
(a) Turn the ignition switch to ON.
(b) When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter
assembly blinks for 6 seconds.
After 1.8 seconds, check that the seat belt warning light on the combination meter assembly changes from
blinking to illuminated.
(c) Lift up the vehicle using a swing arm type lift
.
(d) Start the engine.
(1) Step 1:
When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking
brake is released for 30 seconds or more, check that the seat belt warning light on the combination
meter assembly blinks.
(2) Step 2:
When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph)
or more, check that the seat belt warning light on the combination meter assembly blinks.
After 59.6 seconds, check that the seat belt warning light on the combination meter assembly changes
from blinking to illuminated.
(3) Step 3:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when
the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly
changes from blinking to illuminated.
(4) Step 4:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when
the parking brake is applied, check that the seat belt warning light on the combination meter assembly
changes from blinking to illuminated.
(5) Step 5:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when
the driver seat belt is fastened, check that the seat belt warning light on the combination meter
assembly turns off.
2. INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT
HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front
SEAT BELT: SEAT BELT WARNING SYSTEM: OPERATION CHECK;...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст