Toyota Tundra (2015 year). Manual — part 612
OK
REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 J
Doc ID: RM0000031IU02XX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: Pattern Select Switch Circuit;
2015 MY Tundra [08/2014 - ]
Pattern Select Switch Circuit
DESCRIPTION
The ECM receives tow/haul pattern select switch information and performs the tow/haul control.
While the tow/haul control is operating, in contrast to normal mode, low gears are used to increase engine
braking and towing power, reduce frequent shifts, and improve driveability. The tow/haul control includes throttle
control, shift schedule control, wide open throttle shift timing control and AI-SHIFT control.
Tow/haul mode only operates when the shift lever is in the D position and the tow/haul pattern select switch is
ON.
HINT:
The tow/haul pattern select switch is a momentary-type switch.
In order to cancel tow/haul mode, push the tow/haul pattern select switch again or turn the ignition switch
off.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1.
INSPECT TOW/HAUL PATTERN SELECT SWITCH ASSEMBLY
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
A
(a) for Column Shift Type:
(1) Disconnect the J25 transmission control switch connector.
(2) Measure the resistance according to the value(s) in the
table below.
Standard resistance:
TESTER
CONNECTION
SWITCH CONDITION
SPECIFIED
CONDITION
12 (P) - 9 (E)
Tow/haul pattern select
switch ON
Below 1 Ω
12 (P) - 9 (E)
Tow/haul pattern select
switch OFF
10 kΩ or higher
(b) for Floor Shift Type:
(1) Disconnect the J23 tow/haul pattern select switch
connector.
(2) Measure the resistance according to the value(s) in the
table below.
Standard resistance:
TESTER
CONNECTION
SWITCH CONDITION
SPECIFIED
CONDITION
4 - 1
Tow/haul pattern select
switch ON
Below 1 Ω
4 - 1
Tow/haul pattern select
switch OFF
10 kΩ or higher
Result
RESULT
PROCEED TO
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
B
REPLACE COLUMN SHIFT SHIFT LEVER
SUB-ASSEMBLY (TRANSMISSION CONTROL SWITCH)
C
REPLACE TOW/HAUL PATTERN SELECT SWITCH
ASSEMBLY
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
OK
2.
CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - BODY
GROUND)
(a) for Column Shift Type:
(1) Disconnect the J25 transmission control switch connector.
(2) Measure the resistance according to the value(s) in the
table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
J25-9 (E) - Body ground
Always
Below 1 Ω
(b) for Floor Shift Type:
(1) Disconnect the J23 tow/haul pattern select switch
connector.
(2) Measure the resistance according to the value(s) in the
table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
J23-1 - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
3.
CHECK HARNESS AND CONNECTOR (TOW/HAUL PATTERN SELECT SWITCH - ECM)
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст