Toyota Tundra (2015 year). Manual — part 1891
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
8.
Read the Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
9.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
10.
Input the DTC: P0111.
11.
Check the DTC judgment result.
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].
12.
Check the DTC judgment result again [F].
HINT:
If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F] again.
14.
If no pending DTC is output, perform a universal trip and check for permanent DTCs
.
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
15.
WIRING DIAGRAM
Refer to DTC P0112
.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and
other data from the time the malfunction occurred.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0111; Intake ...
PROCEDURE
1.
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read DTCs.
Result
DISPLAY (DTC OUTPUT)
PROCEED TO
P0111 and other DTCs are output
A
P0111 is output
B
HINT:
If any DTCs other than P0111 are output, troubleshoot those DTCs first.
Perform "Inspection After Repair" after replacing the mass air flow meter
.
B
REPLACE MASS AIR FLOW METER
A
GO TO DTC CHART
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0111; Intake ...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000PF30VGX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0112,P0113; Intake Air Temperature Circuit Low
Input; 2015 MY Tundra [08/2014 - ]
DTC
P0112
Intake Air Temperature Circuit Low Input
DTC
P0113
Intake Air Temperature Circuit High Input
DESCRIPTION
The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the
IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature
voltage changes (see Fig. 1).
changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal,
the ECM increases the fuel injection volume when the engine is cold to improve driveability.
HINT:
When DTC P0112 or P0113 is set, the ECM enters fail-safe mode. During fail-safe mode, the IAT
is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is
detected.
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0112
Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
Short in IAT sensor circuit
IAT sensor (built into MAF meter)
ECM
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0112,P0113; ...
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0113
Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
Open in IAT sensor circuit
IAT sensor (built into MAF meter)
ECM
HINT:
TEMPERATURE DISPLAYED
MALFUNCTION
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit
MONITOR DESCRIPTION
The ECM monitors the sensor voltage and uses this value to calculate the IAT. When the sensor output voltage
deviates from the normal operating range, the ECM interprets this as a malfunction in the IAT sensor and sets
a DTC.
Example:
If the sensor output voltage is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an
open in the IAT sensor circuit, and sets DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5
seconds or more, the ECM determines that there is a short in the sensor circuit, and sets DTC P0112.
If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.
MONITOR STRATEGY
Related DTCs
P0112: IAT sensor range check (Low voltage)
P0113: IAT sensor range check (High voltage)
Required Sensors/Components (Main)
IAT sensor
Required Sensors/Components (Related)
-
Duration
0.5 seconds
MIL Operation
Immediate
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
TYPICAL MALFUNCTION THRESHOLDS
P0112:
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0112,P0113; ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст