Toyota Tundra (2015 year). Manual — part 1061
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002PQE03GX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEMPERATURE SENSOR: INSPECTION; 2015 MY
Tundra [08/2014 - ]
INSPECTION
1. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
(a) Partially immerse the sensor in water and warm up the water.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
1 - 2
Approx. 20°C (68°F)
2.32 k to 2.59 kΩ
1 - 2
Approx. 80°C (176°F)
0.310 k to 0.326 kΩ
If the result is not as specified, replace the engine coolant temperature sensor.
NOTICE:
When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.
HINT:
If the result is as specified, do not replace the engine coolant temperature sensor.
1UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEM...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002PQD03SX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEMPERATURE SENSOR: INSTALLATION; 2015 MY
Tundra [08/2014 - ]
INSTALLATION
HINT:
Perform "Inspection After Repairs" after replacing the engine coolant temperature sensor
.
1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
HINT:
Perform "Inspection After Repairs" after replacing the engine coolant temperature sensor
.
(a) Install a new gasket to the sensor.
(b) Using a 19 mm ball joint lock nut wrench, install the sensor.
Torque:
20 N·m {200 kgf·cm, 14ft·lbf}
NOTICE:
Use the formula to calculate special torque values for situations
where ball joint lock nut wrench is combined with a torque
wrench
.
(c) Connect the sensor connector.
2. ADD ENGINE COOLANT
3. INSPECT FOR COOLANT LEAK
4. INSTALL V-BANK COVER SUB-ASSEMBLY
5. INSTALL NO. 1 ENGINE UNDER COVER
1UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEM...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002PQX02AX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE ENGINE CONTROL SYSTEM: FUEL PUMP RELAY: ON-VEHICLE INSPECTION; 2015 MY Tundra
[08/2014 - ]
ON-VEHICLE INSPECTION
1. REMOVE FUEL PUMP RELAY (F/PMP)
(a) Remove the fuel pump relay from the engine room relay block.
2. INSPECT FUEL PUMP RELAY
(a) Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 5
When no battery voltage is
applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied
to terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the fuel pump relay.
3. INSTALL FUEL PUMP RELAY
(a) Install the fuel pump relay to the engine room relay block.
1UR-FE ENGINE CONTROL SYSTEM: FUEL PUMP RELAY: ON-...
Last Modified: 9-16-2014
6.6 K
Doc ID: RM0000031YK025X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENSOR: COMPONENTS; 2015 MY Tundra
[08/2014 - ]
COMPONENTS
ILLUSTRATION
1UR-FE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENSO...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст