Toyota Tundra (2015 year). Manual — part 2729
OK
OK
*a
*b
GO TO STEP 17
9.
CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR -
NETWORK GATEWAY ECU)
NOTICE:
For vehicles without a blind spot monitor system, go to "Check for Short to GND in CAN Bus Wire (No. 2
Junction Connector - ECM)".
(a) Measure the resistance according to the value(s) in the
table below.
Standard Resistance:
TESTER CONNECTION
SWITCH
CONDITION
SPECIFIED
CONDITION
J74-6 (CANH) - J17-4
(CG)
Ignition switch off
200 Ω or higher
J74-17 (CANL) - J17-4
(CG)
Ignition switch off
200 Ω or higher
Text in Illustration
*a
*b
GO TO STEP 19
10.
CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR -
CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Short t...
A
ECM)
(a) Measure the resistance according to the value(s) in the
table below.
Standard Resistance:
TESTER CONNECTION
SWITCH
CONDITION
SPECIFIED
CONDITION
J74-3 (CANH) - J17-4
(CG)
Ignition switch off
200 Ω or higher
J74-14 (CANL) - J17-4
(CG)
Ignition switch off
200 Ω or higher
Text in Illustration
*a
*b
RESULT
PROCEED TO
OK (w/ Audio and Visual System)
A
OK (w/ Navigation System)
B
NG
C
B
GO TO STEP 12
C
GO TO STEP 21
11.
CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR -
RADIO AND DISPLAY RECEIVER ASSEMBLY)
CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Short t...
(a) Measure the resistance according to the value(s) in the
table below.
Standard Resistance:
TESTER CONNECTION
SWITCH
CONDITION
SPECIFIED
CONDITION
J74-7 (CANH) - J17-4
(CG)
Ignition switch off
200 Ω or higher
J74-18 (CANL) - J17-4
(CG)
Ignition switch off
200 Ω or higher
Text in Illustration
*a
*b
GO TO STEP 23
OK
REPLACE NO. 2 JUNCTION CONNECTOR
12.
CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR -
NAVIGATION RECEIVER ASSEMBLY)
(a) Measure the resistance according to the value(s) in the
table below.
Standard Resistance:
TESTER CONNECTION
SWITCH
CONDITION
SPECIFIED
CONDITION
J74-7 (CANH) - J17-4
(CG)
Ignition switch off
200 Ω or higher
J74-18 (CANL) - J17-4
(CG)
Ignition switch off
200 Ω or higher
Text in Illustration
*a
*b
GO TO STEP 25
CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Short t...
NEXT
OK
REPLACE NO. 2 JUNCTION CONNECTOR
13.
CONNECT CONNECTOR
(a) Reconnect the J74 No. 2 junction connector.
14.
CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER
ASSEMBLY)
(a) Disconnect the J19 air conditioning amplifier assembly
connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
J19-11 (CANH) - J17-4 (CG)
Ignition switch off
200 Ω or higher
J19-12 (CANL) - J17-4 (CG)
Ignition switch off
200 Ω or higher
Text in Illustration
*a
*b
REPAIR OR REPLACE CAN BRANCH WIRE
CONNECTED TO AIR CONDITIONING AMPLIFIER
ASSEMBLY (CANH, CANL)
CAN COMMUNICATION: CAN COMMUNICATION SYSTEM: Short t...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст