Toyota Tundra (2015 year). Manual — part 1509
Heated oxygen sensor heater range check (P0037, P0038, P0057,
P0058, P102D and P105D):
The ECM monitors the current applied to the O2 sensor heater to check the heater for malfunctions. If the
current is below the threshold value, the ECM determines that there is an open circuit in the heater. If the
current is above the threshold value, the ECM determines that there is a short circuit in the heater.
The ECM constantly monitors the current applied to the heater. If the ECM detects an open or short circuit, the
ECM turns the MIL on and sets a DTC.
If a malfunction is detected, the ECM cuts off the current applied to the heater.
Heated oxygen sensor heater performance (P0141 and P0161):
After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using
the battery voltage and the current applied to the heater.
If the resistance is above the threshold value, the ECM determines that there is a malfunction in the HO2
sensor heater and sets DTC P0141 or P0161.
MONITOR STRATEGY
Related DTCs
P0037: Heated oxygen sensor heater (for Bank 1) range check (Low
electrical current)
P0038: Heated oxygen sensor heater (for Bank 1) range check (High
electrical current)
P0057: Heated oxygen sensor heater (for Bank 2) range check (Low
electrical current)
P0058: Heated oxygen sensor heater (for Bank 2) range check (High
electrical current)
P0141: Heated oxygen sensor heater performance (for Bank 1)
P0161: Heated oxygen sensor heater performance (for Bank 2)
P102D: Heated oxygen sensor heater stuck ON (for Bank 1 Sensor 2)
P105D: Heated oxygen sensor heater stuck ON (for Bank 2 Sensor 2)
Required Sensors/Components
(Main)
Heated oxygen sensor heater
Required Sensors/Components
(Related)
-
Once per driving cycle: P0141 and P0161
Duration
0.5 seconds: P0037, P0057, P102D and P105D
Within 3 seconds: P0038 and P0058
10 seconds: P0141 and P0161
MIL Operation
Immediate: P0037, P0038, P0057, P0058, P102D and P105D
2 driving cycles: P0141 and P0161
TYPICAL ENABLING CONDITIONS
P0037 and P0057 (Case 1)
Monitor runs whenever following DTCs not stored
None
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0037,P003...
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
Heater OFF current learned value
Succeeded
Heated oxygen sensor heater high current fail (P0038, P0058)
Not detected
Heater ON current - Learned heater OFF current
0.3 A or less
Heater output
ON
P0037 and P0057 (Case 2)
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
Heated oxygen sensor heater OFF current
Higher than 3.5 A
Heater current detected by heater monitor IC
4 A or more
Heated oxygen sensor heater low current fail (P0037, P0057)
Not detected
Heated oxygen sensor heater high current fail (P0038, P0058)
Not detected
P0038 and P0058
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
P0141 and P0161
Monitor runs whenever following DTCs not stored
None
Heated oxygen sensor heater circuit fail (P0037, P0038, P0057, P0058, P102D and
P105D)
Not detected
Battery voltage
10.5 V or higher
Fuel cut
OFF
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0037,P003...
Time after fuel cut ON to OFF
30 seconds or more
Accumulated heater ON time
100 seconds or
more
Learned heater OFF current operation
Complete
Duration that rear heated oxygen sensor impedance is less than 15 kΩ
2 seconds or more
P102D and P105D
Monitor runs whenever following DTCs not stored
P0031, P0032, P0051, P0052 (Air fuel ratio sensor
heater)
P0037, P0038, P0057, P0058 (Rear oxygen sensor
heater)
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
Heated oxygen sensor heater low current fail (P0037
and P0057)
Not detected
Heated oxygen sensor heater high current fail (P0038
and P0058)
Not detected
TYPICAL MALFUNCTION THRESHOLDS
P0037 and P0057 (Case 1)
Heater current - Learned heater OFF current
0.3 A or less
P0037 and P0057 (Case 2)
Heated oxygen sensor heater ON current
1 A or less
P0038 and P0058
Heater current detected by heater monitor IC
4 A or more
Command to heater output
ON
P0141 and P0161
Accumulated heater resistance
Varies with sensor element temperature (Example: More than 23 Ω)
P102D and P105D
Heated oxygen sensor heater ON current
Higher than 1 A
COMPONENT OPERATING RANGE
Heated Oxygen (HO2) sensor heater
0.4 to 1 A (when engine idles, HO2 sensor warmed up and battery
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0037,P003...
current
voltage 11 to 14 V)
MONITOR RESULT
Refer to CHECKING MONITOR STATUS
.
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
1.
Turn the ignition switch to ON and turn the Techstream ON.
2.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
3.
Turn the ignition switch off and wait for at least 30 seconds.
4.
Turn the ignition switch to ON and turn the Techstream on [A].
5.
Start the engine and idle it for 5 minutes or more [B].
6.
7.
Idle the engine for 5 minutes or more [D].
8.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
9.
Read the pending DTC.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
10.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
11.
Input the DTC: P0037, P0038, P0057, P0058, P0141, P0161, P102D or P105D.
12.
Check the DTC judgment result.
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
13.
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0037,P003...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст