Toyota Tundra (2015 year). Manual — part 596
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
(clutch, brake, gear,
etc.)
P2714
The ECM detects a malfunction on SLT (ON side) according to the
Shift solenoid valve SLT
remains open or closed
Shift solenoid valve S1,
S2, S3, S4 or SL2
remains open or closed
Gear 6 incorrect ratio
(sequence valve) or 1-2
shift valve is stuck
Valve body is blocked
Automatic transmission
(clutch, brake, gear,
etc.)
MONITOR DESCRIPTION
When the shift solenoid valve SLT remains ON, oil pressure decreases, which causes the clutch
engagement force to decrease.
When the shift solenoid valve remains ON or OFF, the gear position commanded by the ECM and the
actual gear position are not the same.
NOTICE:
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be
drivable.
MONITOR STRATEGY
Related DTCs
P0894: Automatic transmission slip malfunction
P2714: Shift solenoid valve SLT/Functional check
Required sensors/Components
Shift solenoid valve SLT
Duration
P0894 ON malfunction (A): Immediately
P0894 ON malfunction (B): 0.4 seconds
P2714: Immediately
MIL operation
2 driving cycles
TYPICAL ENABLING CONDITIONS
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
All
The monitor will run whenever the following
DTCs are not present
P0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0710, P0712, P0713, P2740, P2742, P2743 (ATF
temperature sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0979, P0980 (Shift solenoid valve S3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P2716 (Shift solenoid valve SLT circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant
temperature) sensor circuit)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D
(KCS sensor circuit)
ETCS (Electric Throttle Control System)
Not system down
Transmission position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or higher
Spark advance from max. retard timing by KCS
control
0° crankshaft angle or more
Engine
Starting
TYPICAL MALFUNCTION THRESHOLDS
[P0894: ON malfunction]
When either condition below is met: ON malfunction (A) or (B)
ON Malfunction (A)
ON Malfunction (B)
Actual gear for SLT failure judgment
Not determined
[P2714: ON malfunction]
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
ON Malfunction (B)
Shift solenoid valve S1 OFF malfunction
Detected
ON Malfunction (C)
Shift solenoid valve S2 OFF malfunction
Detected
ON Malfunction (D)
Shift solenoid valve S3 ON malfunction
Detected
ON Malfunction (E)
Shift solenoid valve S4 OFF malfunction
Detected
ON Malfunction (F)
1-2 shift valve malfunction
Detected
ON Malfunction (G)
Reverse sequence valve malfunction
Detected
ON Malfunction (H)
Shift solenoid valve SL2 ON malfunction
Detected
INSPECTION PROCEDURE
NOTICE:
Perform the universal trip to clear permanent DTCs
.
PROCEDURE
1.
CHECK DTC OUTPUT (IN ADDITION TO DTCS P0894 AND P2714)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs using the Techstream.
Result
RESULT
PROCEED TO
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
A
RESULT
PROCEED TO
Only P0894 is output
Only P0894 and P2714 are output
A
P0894, P2714 and other DTCs are output
B
HINT:
If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.
B
GO TO DTC CHART
2.
PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)
NOTICE:
Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
Be careful to prevent SST's hose from interfering with the exhaust pipe.
Perform the test with the A/C OFF.
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be
operated without removing any parts. This non-intrusive functional inspection can be very useful because
intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early
in troubleshooting is one way to save diagnostic time. Data List information can be displayed while
performing Active Tests.
(a) Remove the test plug on the transmission case center right
side and connect SST.
SST: 09992-00095
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст