Toyota Tundra (2015 year). Manual — part 720
OK
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
6 (SR) - Body ground
20°C (68°F)
11 to 15 Ω
NG
GO TO STEP 3
2.
CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
(a) Disconnect the D74 ECM connector.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
D74-4 (SR) - Body ground
20°C (68°F)
11 to 15 Ω
Result
RESULT
PROCEED TO
NG
A
OK (for 3UR-FE)
B
OK (for 3UR-FBE)
C
B
REPLACE ECM
C
REPLACE ECM
A
REPAIR OR REPLACE HARNESS OR CONNECTOR
3.
INSPECT SHIFT SOLENOID VALVE SR
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
(a) Remove shift solenoid valve SR.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION SPECIFIED CONDITION
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body
20°C (68°F)
11 to 15 Ω
OK:
Valve moves and makes an operating noise.
NG
REPLACE SHIFT SOLENOID VALVE SR
OK
REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000W8A0M5X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P2716; Pressure Control
Solenoid "D" Electrical (Shift Solenoid Valve SLT); 2015 MY Tundra [08/2014 - ]
DTC
P2716
Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)
DESCRIPTION
Refer to DTC P0894
.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P2716
Open or short is detected in shift solenoid valve SLT circuit for
1 second or more while driving (1 trip detection logic)
Open or short in shift
solenoid valve SLT circuit
Shift solenoid valve SLT
ECM
MONITOR DESCRIPTION
When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The
ECM will turn on the MIL and store the DTC.
MONITOR STRATEGY
Related DTCs
P2716: Shift solenoid valve SLT/Range check
Required sensors/Components
Shift solenoid valve SLT
Duration
1 second
MIL operation
Immediately
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not present
None
Solenoid current cut status
Not cut
Battery voltage
11 V or more
Ignition switch
ON
Starter
OFF
TYPICAL MALFUNCTION THRESHOLDS
Solenoid voltage monitor signal from solenoid driver MIC
No signal
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
COMPONENT OPERATING RANGE
Output signal duty
Less than 100%
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Perform the universal trip to clear permanent DTCs
.
PROCEDURE
1.
INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
(a) Disconnect the D63 No. 1 transmission wire connector.
(b) Measure the resistance according to the value(s) in the table below.
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст