Toyota Tundra (2015 year). Manual — part 2109
OK
Standard resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
J50-5 (CCTY) - DD-46
Always
Below 1 Ω
J50-7 (E) - Body ground
J50-5 (CCTY) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
7.
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
(a) Disconnect the J2 and J3 ECU connectors.
(b) Measure the voltage according to the value(s) in the table
below.
Standard voltage:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED
CONDITION
J2-14 (CGLP) - Body
ground
Cargo light switch ON or
DOOR
11 to 14 V
Cargo light switch OFF
Below 1 V
(c) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED
CONDITION
J3-9 (CGSW) - Body
ground
Cargo light switch ON
Below 1 Ω
Cargo light switch DOOR
or OFF
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU
LIGHTING: LIGHTING SYSTEM: Cargo Light Circuit; 2015 MY Tund...
Last Modified: 9-16-2014
6.6 K
Doc ID: RM000002VDQ009X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: LIGHTING: REAR COMBINATION LIGHT ASSEMBLY: COMPONENTS; 2015 MY Tundra [08/2014 - ]
COMPONENTS
ILLUSTRATION
LIGHTING: REAR COMBINATION LIGHT ASSEMBLY: COMPO...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002VDR009X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: LIGHTING: REAR COMBINATION LIGHT ASSEMBLY: REMOVAL; 2015 MY Tundra [08/2014 - ]
REMOVAL
HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. REMOVE REAR COMBINATION LIGHT ASSEMBLY LH
(a) Put protective tape around the rear combination light assembly LH.
(b) Using a T30 "TORX" socket wrench, remove the 2 screws.
(c) Detach the 2 clips.
(d) Disconnect each connector and remove the rear combination light assembly LH.
Text in Illustration
*1
Protective Tape
-
-
2. REMOVE REAR COMBINATION LIGHT GUIDE
HINT:
If the rear combination light assembly LH is removed, replace
the rear combination light guide.
Use the same procedure for both rear combination light guides.
(a) Using a screwdriver, detach the 2 claws and remove the rear
combination light guide.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Tape
LIGHTING: REAR COMBINATION LIGHT ASSEMBLY: REMOVAL...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002VDS009X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: LIGHTING: REAR COMBINATION LIGHT ASSEMBLY: DISASSEMBLY; 2015 MY Tundra [08/2014 - ]
DISASSEMBLY
HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. REMOVE REAR TURN SIGNAL LIGHT BULB
(a) Turn the rear turn signal light bulb socket with the rear turn signal light bulb in the direction indicated by
the arrow to remove them as a unit.
(b) Remove the rear turn signal light bulb from the rear turn signal
light bulb socket.
2. REMOVE BACK UP LIGHT BULB
(a) Turn the back up light bulb socket with the back up light bulb in the direction indicated by the arrow to
remove them as a unit.
LIGHTING: REAR COMBINATION LIGHT ASSEMBLY: DISASS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст