Toyota Tundra (2015 year). Manual — part 1964
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000002I3U0HIX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0657; Actuator Supply Voltage Circuit / Open; 2015
MY Tundra [08/2014 - ]
DTC
P0657
Actuator Supply Voltage Circuit / Open
DESCRIPTION
The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is
functioning properly. The output voltage usually is 0 V when the ignition switch is turned off. If the output
voltage is higher than 7 V when the ignition switch is turned off, the ECM will illuminate the MIL and set a DTC
when the ignition switch is turned to ON.
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0657
Throttle actuator power supply error
ECM
MONITOR STRATEGY
Related DTCs
None
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
Throttle actuator
Duration
-
MIL operation
Immediate
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Ignition switch
ON to OFF
Throttle actuator power supply voltage
7 V or more
TYPICAL MALFUNCTION THRESHOLDS
Throttle actuator power supply
ON
CONFIRMATION DRIVING PATTERN
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0657; Actuat...
Connect the Techstream to the DLC3.
1.
Turn the ignition switch to ON and turn the Techstream on.
2.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
3.
Turn the ignition switch off and wait for at least 30 seconds.
4.
Turn the ignition switch to ON and turn the Techstream on.
5.
Wait 5 seconds or more [A].
6.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
7.
Read the Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
8.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
9.
Input the DTC: P0657.
10.
Check the DTC judgment result.
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
11.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and
12.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0657; Actuat...
check for permanent DTCs
.
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
INSPECTION PROCEDURE
NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the
negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the
negative (-) battery terminal notices before proceeding with work
.
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition
information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame
data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if
the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
CHECK DTC
(a) Clear DTC
.
(b) Turn the ignition switch off.
(c) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the ignition switch to ON for 10 seconds.
(f) Turn the ignition switch off.
(g) Turn the ignition switch to ON.
(h) Check DTC.
OK:
P0657 is not present.
NG
REPLACE ECM
OK
INTERMITTENT PROBLEMS
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0657; Actuat...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000W880WJX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0724; Brake Switch "B" Circuit High; 2015 MY
Tundra [08/2014 - ]
DTC
P0724
Brake Switch "B" Circuit High
DESCRIPTION
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0724
Stop light switch remains ON even when vehicle is driven in GO (30
km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph))
pattern 5 times (2 trip detection logic)
Short in stop
light switch
signal circuit
Stop light switch
ECM
MONITOR DESCRIPTION
This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and
STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM
stores the DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86
mph)) 5 times for 2 driving cycles in order for the DTC to be output.
MONITOR STRATEGY
Related DTCs
P0724: Stop light switch/Range check/Rationality
Required sensors/Components
Stop light switch, Vehicle speed sensor
Duration
GO and STOP 5 times
MIL operation
2 driving cycles
TYPICAL ENABLING CONDITIONS
The monitor will run whenever this DTC is not present.
None
Battery voltage
8 V or more
Starter
OFF
Ignition switch
ON
GO: Vehicle speed
30 km/h (18.65 mph) or more
STOP: Vehicle speed
Less than 3 km/h (1.86 mph)
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0724; Brake...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст