Toyota Tundra (2015 year). Manual — part 796
Torque:
441 N·m {4497 kgf·cm, 325ft·lbf}or less
If the maximum torque is exceeded while retightening the
nut, replace the bearing spacer and repeat the preload
adjusting procedure.
HINT:
Do not loosen the pinion nut to reduce the preload.
24. INSPECT TOTAL PRELOAD
(a) Using a torque wrench, measure the preload with the teeth of
the drive pinion and ring gear in contact.
Standard total preload (at starting):
Standard drive pinion preload plus 0.24 to 0.46 N*m (3 to 4
kgf*cm, 3 to 4 in.*lbf)
25. INSPECT DIFFERENTIAL RING GEAR BACKLASH
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
If the backlash is not as specified, adjust the side bearing
preload or repair as necessary.
HINT:
Perform the measurements at 3 or more positions
Text in Illustration
*a
72 mm (2.83 in.)
Maximum runout:
RUNOUT
SPECIFIED CONDITION
Vertical runout
0.10 mm (0.00394 in.)
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
RUNOUT
SPECIFIED CONDITION
Lateral runout
0.10 mm (0.00394 in.)
If the runout is more than the maximum, replace the
companion flange.
27. STAKE REAR DRIVE PINION NUT
(a) Using a chisel and hammer, stake the nut.
28. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING
NUT LOCK
(a) Install 2 new adjusting locks onto the bearing caps with the 2
bolts.
Torque:
13 N·m {130 kgf·cm, 9ft·lbf}
(b) Bend the nut locks.
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM00000174J017X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-FE): INSTALLATION; 2015 MY Tundra
[08/2014 - ]
INSTALLATION
1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
(b) Install a new gasket and the differential carrier with the 10 washers and 10 nuts.
Torque:
72 N·m {734 kgf·cm, 53ft·lbf}
NOTICE:
Be careful not to damage the installation surface.
2. INSTALL REAR AXLE SHAFT LH
(a) Install the rear axle shaft LH
.
3. INSTALL REAR AXLE SHAFT RH
HINT:
Use the same procedure described for the LH side.
4. INSTALL PROPELLER SHAFT ASSEMBLY
(a) Install the propeller shaft for 2WD
.
(b) Install the propeller shaft for 4WD
.
5. ADD DIFFERENTIAL OIL
6. INSTALL REAR WHEEL
(a) Install the rear wheels.
Torque:
for Aluminum Wheel -
131 N·m {1336 kgf·cm, 97ft·lbf}
for Steel Wheel -
209 N·m {2131 kgf·cm, 154ft·lbf}
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
Last Modified: 9-16-2014
6.6 K
Doc ID: RM0000031DB012X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-FE, 3UR-FBE): COMPONENTS; 2015 MY
Tundra [08/2014 - ]
COMPONENTS
ILLUSTRATION
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст