Toyota Tundra (2015 year). Manual — part 2810
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002GN3014X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SUSPENSION: FRONT UPPER SUSPENSION ARM: DISASSEMBLY; 2015 MY Tundra [08/2014 - ]
DISASSEMBLY
1. REMOVE FRONT SUSPENSION UPPER ARM BUSH
(b) Using SST and a press, press out the bush.
SST: 09613-26010
SST: 09710-22021
09710-01031
SST: 09950-00020
2. REMOVE FRONT UPPER BALL JOINT DUST COVER LH
(a) Using a snap ring expander, remove the dust cover set ring.
SUSPENSION: FRONT UPPER SUSPENSION ARM: DISASSEMBLY...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002ZPN013X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SUSPENSION: FRONT UPPER SUSPENSION ARM: INSPECTION; 2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT FRONT SUSPENSION UPPER ARM ASSEMBLY
LH
(a) As shown in the illustration, flip the ball joint stud back and forth
5 times, before installing the nut.
turn.
Standard turning torque:
0.98 to 4.41 N*m (1.0 to 45 kgf*cm, 9 to 39 in.*lbf)
SUSPENSION: FRONT UPPER SUSPENSION ARM: INSPECTION; ...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002GN4014X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SUSPENSION: FRONT UPPER SUSPENSION ARM: REASSEMBLY; 2015 MY Tundra [08/2014 - ]
REASSEMBLY
1. INSTALL FRONT UPPER BALL JOINT DUST COVER LH
(a) Pack the upper arm ball joint with MP grease.
Grease capacity:
5.0 to 7.0 g (0.176 to 0.247 oz.)
(b) Using a snap ring expander, install the dust cover set ring.
2. INSTALL FRONT SUSPENSION UPPER ARM BUSH
(a) Using SST and a press, press in a new bush.
SST: 09710-26011
09710-05061
SUSPENSION: FRONT UPPER SUSPENSION ARM: REASSEMBLY;...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002C8I025X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: SUSPENSION: FRONT UPPER SUSPENSION ARM: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the standard bolt chart
.
1. TEMPORARILY INSTALL FRONT SUSPENSION UPPER
ARM ASSEMBLY LH
(a) Temporarily install the suspension upper arm with the 2
washers, bolt and nut.
HINT:
After stabilizing the suspension, tighten the nut.
2. INSTALL FRONT FENDER APRON SEAL REAR LH
(a) Install the apron seal with the 5 clips.
3. INSTALL FRONT FENDER APRON SEAL LH
(a) Install the apron seal with the 6 clips.
4. CONNECT STEERING KNUCKLE LH
(a) Connect the steering knuckle to the suspension upper arm.
(b) Install the nut and a new cotter pin.
Torque:
110 N·m {1122 kgf·cm, 81ft·lbf}
NOTICE:
If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.
5. CONNECT SKID CONTROL SENSOR WIRE
(a) Connect the sensor wire to the steering knuckle and upper arm
with the 2 bolts.
Torque:
for Bolt A -
13 N·m {133 kgf·cm, 10ft·lbf}
for Bolt B -
29 N·m {296 kgf·cm, 21ft·lbf}
SUSPENSION: FRONT UPPER SUSPENSION ARM: INSTALLATIO...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст