Toyota Tundra (2015 year). Manual — part 2585
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002HA700XX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE EXHAUST: EXHAUST PIPE: REMOVAL; 2015 MY Tundra [08/2014 - ]
REMOVAL
CAUTION:
Wear protective gloves when removing the exhaust pipe assembly.
The exhaust pipe assembly is extremely hot immediately after the engine has stopped.
Confirm that the exhaust pipe assembly has cooled down before removing it.
1. REMOVE TAILPIPE ASSEMBLY
(a) Remove the bolt and clamp.
(b) Disconnect the exhaust pipe support to remove the tailpipe assembly.
(c) Remove the gasket.
2. REMOVE CENTER EXHAUST PIPE ASSEMBLY
(a) Remove the 4 bolts.
(b) Disconnect the 3 exhaust pipe supports to remove the center exhaust pipe assembly.
(c) Remove the 2 gaskets.
3. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
4. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
(a) Remove the 3 nuts.
(b) Disconnect the exhaust pipe support to remove the front No. 2 exhaust pipe assembly.
(c) Remove the gasket.
5. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)
6. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
7. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(a) Remove the 3 nuts and front exhaust pipe assembly.
(b) Remove the gasket.
8. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)
9. REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
3UR-FE EXHAUST: EXHAUST PIPE: REMOVAL; 2015 MY Tundra [...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000005KA4008X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE EXHAUST: EXHAUST PIPE: DISASSEMBLY; 2015 MY Tundra [08/2014 - ]
DISASSEMBLY
1. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 1)
(a) Remove the 4 bolts, 4 nuts, lower monolithic converter protector, upper monolithic converter
protector, 2 No. 1 converter protector stays and 2 No. 2 converter protector stays from the front No. 2
exhaust pipe assembly.
2. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1)
(a) Remove the 4 bolts, 4 nuts, lower No. 1 monolithic converter protector, upper No. 1 monolithic
converter protector and 4 No. 1 converter protector stays from the front No. 2 exhaust pipe assembly.
3. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 2)
(a) Remove the 4 bolts, 4 nuts, lower monolithic converter protector, upper monolithic converter
protector, 2 No. 1 converter protector stays and 2 No. 2 converter protector stays from the front
exhaust pipe assembly.
4. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2)
(a) Remove the 4 bolts, 4 nuts, lower No. 1 monolithic converter protector, upper No. 1 monolithic
converter protector and 4 No. 1 converter protector stays from the front exhaust pipe assembly.
3UR-FE EXHAUST: EXHAUST PIPE: DISASSEMBLY; 2015 MY Tun...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст