Toyota Tundra (2015 year). Manual — part 2227
Remove the visor
.
16. REMOVE VISOR ASSEMBLY RH
HINT:
Use the same procedures described for the LH side.
17. REMOVE VISOR HOLDER
(a) for Regular Cab:
Remove the visor holder
.
(b) for Double Cab, w/o Illumination:
Remove the visor holder
.
(c) for CrewMax, w/o Illumination:
Remove the visor holder
.
18. REMOVE ASSIST GRIP SUB-ASSEMBLY
(a) for Regular Cab, for Double Cab:
Remove the assist grip
.
(b) for CrewMax:
Remove the assist grip
.
19. REMOVE COAT HOOK
20. REMOVE ROOF HEADLINING ASSEMBLY
For Regular Cab, refer to the following procedures
.
For Double Cab, refer to the following procedures
.
For CrewMax, refer to the following procedures
.
21. REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH
22. REMOVE REAR ROOF DRIP SIDE FINISH MOULDING RH
HINT:
Use the same procedures described for the LH side.
23. REMOVE ROOF DRIP SIDE FINISH MOULDING LH
24. REMOVE ROOF DRIP SIDE FINISH MOULDING RH
HINT:
Use the same procedures described for the LH side.
25. REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: REMOV...
26. REMOVE OUTSIDE WINDSHIELD MOULDING
(a) Using a knife, cut off the moulding as shown in the illustration.
NOTICE:
Be careful not to damage the vehicle body.
(b) Remove the remaining moulding.
HINT:
Make a partial cut in the moulding. Then pull and remove it by
hand.
27. REMOVE UPPER WINDSHIELD OUTSIDE MOULDING
(a) Using a knife, cut off the moulding as shown in the illustration.
NOTICE:
Be careful not to damage the vehicle body.
(b) Remove the remaining moulding.
HINT:
Make a partial cut in the moulding. Then pull and remove it by
hand.
28. REMOVE WINDSHIELD GLASS
(a) w/ Windshield Deicer:
Remove the clip and disconnect the connector.
(d) Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: REMOV...
NOTICE:
When separating the glass from the vehicle, be careful not to damage the vehicle's paint or
interior/exterior ornaments.
To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet
between the piano wire and instrument panel.
(e) Place matchmarks over the glass and vehicle body on the
locations indicated in the illustration.
HINT:
Matchmarks do not need to be placed if not reusing the glass.
(f) Cut through the adhesive by pulling the piano wire around the glass.
NOTICE:
Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
(g) Disengage the stoppers.
(h) Using suction cups, remove the glass.
29. CLEAN WINDSHIELD GLASS
(a) Using a scraper, remove the damaged stoppers, dams and
adhesive sticking to the glass.
NOTICE:
Even if using new glass, clean it with non-residue solvent.
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: REMOV...
30. CLEAN VEHICLE BODY
away excess adhesive as shown in the illustration.
HINT:
Leave as much adhesive on the vehicle body as possible.
NOTICE:
Be careful not to damage the vehicle body.
Even if all the adhesive has been removed, clean the vehicle
body.
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: REMOV...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст