Toyota Tundra (2015 year). Manual — part 1227
OK
A
39.
READ FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were
present when the DTC was stored
.
Result
FREEZE FRAME DATA ITEM
FOR DTC P1605
RESULT
SUSPECTED AREA
PROCEED
TO
Calculate Load
Mass air flow meter
A
AFS Voltage B1S1
AFS Voltage B2S1
Below 3.3 V*2
Air fuel ratio
sensor
Harness and
connector
B
Both freeze frame data items
listed above
Values are other than above
-
C
HINT:
GO TO STEP 43
C
GO TO STEP 46
40.
CHECK MASS AIR FLOW METER
(a) Remove the mass airflow meter.
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P1605;...
A
OK
RESULT
PROCEED TO
Visible foreign matter is not present
A
Visible foreign matter is present
B
HINT:
Perform "Inspection After Repair" after replacing the mass air flow meter
.
B
REPLACE MASS AIR FLOW METER
41.
CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
(a) Check the harnesses and connectors, referring to DTC P0102 inspection procedure
.
HINT:
REPAIR OR REPLACE HARNESS OR CONNECTOR
42.
PERFORM DRIVE TEST
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature stabilizes.
HINT:
The A/C switch and all accessory switches should be off.
(c) Idle the engine.
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P1605;...
OK
DATA LIST
SPECIFIED CONDITION
Calculate Load
Perform "Inspection After Repair" after replacing the mass air flow meter
.
NG
REPLACE MASS AIR FLOW METER
43.
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR
A/F SENSOR)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Start the engine, turn off all accessory switches and warm up the engine until the engine coolant
temperature stabilizes.
(d) Idle the engine.
(e) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume
for A/F Sensor.
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P1605;...
A
OK
(f) Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel
injection volume.
Standard:
TECHSTREAM DISPLAY
SPECIFIED CONDITION
Control the Injection Volume for A/F Sensor (+12.5%)
Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%)
Air fuel ratio sensor output voltage is higher than 3.4 V
Result
RESULT
PROCEED TO
Abnormal
A
Normal
B
HINT:
B
GO TO STEP 46
44.
CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
(a) Check the harnesses and connectors, referring to DTC P0031 inspection procedure
.
HINT:
REPAIR AIR FUEL RATIO SENSOR POWER SOURCE
CIRCUIT
45.
CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
(a) Check the harnesses and connectors, referring to DTC P2237 inspection procedure
.
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P1605;...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст