Toyota Tundra (2015 year). Manual — part 1862
5. DLC3 (Data Link Connector 3)
Check the DLC3
.
6. BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If voltage is below 11 V, replace or recharge the battery before proceeding.
7. MIL (Malfunction Indicator Lamp)
(a) The MIL is illuminated when the ignition switch is first turned ON (the engine is not running).
(b) The MIL should turn OFF when the engine is started. If the MIL remains illuminated, the diagnosis
system has detected a malfunction or abnormality in the system.
HINT:
If the MIL is not illuminated when the ignition switch is first turned ON, check the MIL circuit
.
8. ALL READINESS
HINT:
With "ALL READINESS" you can check whether or not the DTC judgment has been completed by using
the Techstream.
You should check "ALL READINESS" after simulating malfunction symptoms or for validation after
finishing repairs.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs
.
(e) Perform the DTC judgment driving pattern to run the DTC judgment.
(f) Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
(g) Input the DTCs to be confirmed.
(h) Check the DTC judgment result.
DISPLAY
ITEM
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
You should perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DIAGNOSIS...
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000000PDK1ASX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DTC CHECK / CLEAR; 2015 MY Tundra [08/2014 -
]
DTC CHECK / CLEAR
NOTICE:
When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and
Pending DTC
Store
condition
Malfunction detected
Clear
condition
System determined to be normal
or
DTCs cleared using Techstream
or
Cable disconnected from negative battery terminal
Current DTC
Store
condition
Malfunction detected (2nd trip)
Clear
condition
No malfunctions in 40 driving cycles
or
DTCs cleared using Techstream
or
Cable disconnected from negative battery terminal
Permanent
DTC
Store
condition
Malfunction detected (2nd trip)
Clear
condition
Ignition switch turned to ON after normal judgment obtained in 3 consecutive
driving cycles
or
After DTCs cleared using Techstream or cable disconnected from negative battery
terminal, normal judgment obtained and universal trip performed (not for misfire
and fuel system DTCs)
or
After DTCs cleared using Techstream or cable disconnected from negative battery
terminal, malfunction not detected when universal trip driving performed (misfire
and fuel system DTCs)
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DTC CHECK ...
MIL
ON
Malfunction detected (2nd trip)
OFF
Ignition switch turned to ON after normal judgment obtained in 3 consecutive
driving cycles
or
DTCs cleared using Techstream
or
Cable disconnected from negative battery terminal
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DTC CHECK ...
HINT:
Obtaining a normal judgment and performing a universal trip driving pattern can be done in the same
driving cycle or in different driving cycles.
It is unnecessary to obtain a normal judgment if the DTCs are misfire or fuel system DTCs.
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Check the DTC(s) and freeze frame data, and then write them down.
.
2. CLEAR DTC (Pending and Current DTC)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Clear the DTCs.
3. CLEAR DTC (Pending and Current DTC without using Techstream)
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DTC CHECK ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст