Toyota Tundra (2015 year). Manual — part 781
09955-04061
09957-04010
09958-04011
SST: 09950-60010
09951-00550
SST: 09950-00020
SST: 09950-00030
3. REMOVE FRONT AXLE HUB OIL SEAL
(a) Using a screwdriver, pry the oil seal.
4. REMOVE PLUG (for 2WD)
(a) Using a screwdriver and hammer, remove the plug.
AXLE: FRONT AXLE HUB: DISASSEMBLY; 2015 MY Tundra [08/2...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000016X802RX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AXLE: FRONT AXLE HUB: REASSEMBLY; 2015 MY Tundra [08/2014 - ]
REASSEMBLY
NOTICE:
Do not allow foreign matter, etc. to contact the ABS rotor bearing.
1. INSTALL PLUG (for 2WD)
(a) Using the SST and a hammer, install a new plug.
SST: 09950-60010
09951-00450
SST: 09950-70010
09951-07100
2. INSTALL FRONT AXLE HUB OIL SEAL
(a) Using SST and a press, press in a new oil seal.
SST: 09608-36010
SST: 09950-70010
09951-07100
NOTICE:
Do not damage the oil seal.
3. INSTALL FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY
(a) Using SST and a press, press in a new bearing.
SST: 09608-32010
NOTICE:
Insert 4 bolts into the bearing before installing the axle hub.
Make sure to securely fit the bearing to the axle hub.
4. INSTALL FRONT WHEEL ADJUSTING NUT (for 2WD)
AXLE: FRONT AXLE HUB: REASSEMBLY; 2015 MY Tundra [08/20...
(a) Using SST, install a new adjusting nut.
SST: 09602-60010
Torque:
382 N·m {3895 kgf·cm, 282ft·lbf}
AXLE: FRONT AXLE HUB: REASSEMBLY; 2015 MY Tundra [08/20...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000016X403XX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AXLE: FRONT AXLE HUB: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for 2WD)
(a) Apply MP grease to a new O-ring.
(b) Install the O-ring to the axle hub.
NOTICE:
Do not damage the O-ring.
(c) Install the dust cover and axle hub to the steering knuckle with
the 4 bolts.
Torque:
99 N·m {1010 kgf·cm, 73ft·lbf}
2. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for 4WD)
(a) Apply MP grease to a new O-ring.
(b) Install the O-ring to the axle hub.
NOTICE:
Do not damage the O-ring.
(c) Connect the front drive shaft to the front axle hub.
NOTICE:
Be careful not to damage the front drive shaft boot.
(d) Install the dust cover and axle hub to the steering knuckle with
the 4 bolts.
Torque:
99 N·m {1010 kgf·cm, 73ft·lbf}
3. INSTALL FRONT AXLE HUB NUT LH (for 4WD)
(a) Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.
AXLE: FRONT AXLE HUB: INSTALLATION; 2015 MY Tundra [08/...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст